Marco .. and Wrenches ..
I'm going to take a run at this -- just once.
First ...
Without proper and *accurate* data acquisition equipment, there's no way
to know what the actual available PV wattage is compared to the inverter's
output wattage when its output is being *LIMITED*. This limiting action
occurs in an inverter when there's more available power at the input than
the inverter can produce at its output. Subsequently, you don't know how
much potential energy wasn't harvested.
Now then ...
Let's say the inverter is producing 216 watts, and the PV *could* produce
227.3 watts at max power point under those specific conditions if every
PV-generated milliwatt were used.
Next, and presuming the inverter is 95% efficient, that's a "limited loss" of
ONE WATT. 227.3 x 95% = 215.94 watts (OK, so I fudged 0.06 watt).
Under what conditions (and since you're in Hawaii, I'll use 70F) would this
occur, and with what size PV?
I went to my magic spreadsheet and grabbed the first 270-watt-rated PV I
could find. NESL DJ-270P,.
YOU think it's producing 270 watts. It's not. At 77F (25C), and under the
conditions of 100% irradiance, perfectly orthogonal to the sun at mid-day,
light wind, that particular PV will produce 227 watts +/- its tolerance.
(Let's say the tolerance is dead on.)
Now, consider the benefit of increased energy output due to more rapid
output wattage rise experienced during early morning, and the higher
output later in the afternoon, AS WELL AS the increased power output
realized during periods of less than 100% irradiance one derives from
using larger PV compared to PV you might consider "perfectly matched"
to the inverter.
ALL of this adds up to more kilowatt-hours produced annually than had the
inverter been connected to your "perfect" PV that doesn't produce enough
wattage to have the inverter begin limiting its output. The "shoulders" of the
output wattage curve are steeper than with lower-wattage PV.
Granted you *could* connect the inverter to [say] a 450 watt PV module,
and >that< would truly be a waste of the PV wattage. There *is* a broad
"sweet spot" for AC Module inverters and microinverters alike, and it's
actually on the higher side of the PV's rated output wattage versus the
inverter's wattage rating. So, can you over-do it? Sure. But there IS an
overall kilowatt-hours-produced benefit for *modest* over-sizing the PV.
What I *can't* answer is the long-term effect this may have on the overall
life of the inverter. THAT depends on various intricate design considerations
that went into creating the inverter in the first place.
This isn't an Enphase issue, nor are they trying to mislead you on this topic.
It's an industry-wide issue. Wrenches face it every time you designed a string
system, especially those being installed in regions with wide temperature
swings.
Trying to explain in depth the "how and why" slightly larger PV is of benefit
to a customer is like trying to explain photovoltaic equipment to the general
public.
As a competitor to Enphase .. I'm not coming to their defense. However,
what Nick said (below) IS fact.
Whether you elect to believe this or not is up to you.
Regards to all,
Dan Lepinski, Senior Engineer
Exeltech / Exeltech Solar Products
With 41 years experience as a design engineer in solar energy.
--- On Sat, 3/23/13, Marco Mangelsdorf <ma...@pvthawaii.com> wrote:
From: Marco Mangelsdorf <ma...@pvthawaii.com>
Subject: [RE-wrenches] P1 micro performance
To: "'RE-wrenches'" <re-wrenches@lists.re-wrenches.org>
Date: Saturday, March 23, 2013, 4:04 AM
Yes, I know that that screen shot was only a moment in time. Here it’s only
March and clipping is already taking place. Imagine what kind of clipping is
going to take place at higher irradiance levels later in the year. Yes, the
monitoring program cannot as of now quantify what kind of harvesting losses
would take place over time compared to an identical array using Enphase micros.
But the principle remains unchallengeable: not allowing for maximum kWh
harvesting is plain and simple NOT the best design strategy. “Some clipping is
good”? You’ve got to be joking. Not being able to harvest usable solar energy
is good? What kind of optimal design philosophy is that? As module outputs
have been going up, Enphase has a vested interest in continuing to move product
with little regard for the harvestable energy being essentially lost. Using
larger micros that reduce or eliminate that clipping is prima facie a good
thing if one cares
about maximizing kWh harvest. As more micro products come on the product with
higher outputs than the venerable and solid M215, Enphase risks being left
behind and losing market share. I for one find that “white paper” overly
self-serving. marco From: re-wrenches-boun...@lists.re-wrenches.org
[mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Nick Soleil
Sent: Thursday, March 21, 2013 8:04 PM
To: RE-wrenches
Subject: Re: [RE-wrenches] P1 micro performance Good points David, we are in
peak season for inverters to be limiting power.
Marco, your diagram shows that the modules are only overproducing the Enphase
M215's output of 225 watts for a single 15 minute period during the day. That
would only equate to about 3 watt-hours of lost power on a day when the modules
are producing more than 1000 watt-hours. That tends to be in agreement with
our study, which can be viewed at;
http://enphase.com/wp-uploads/enphase.com/2011/12/Enphase_White_Paper_Module_Rightsizing.pdf.
Averaged across the entire year, this loss of power would total less than
0.1%, and would be less than 0.2% for a 265 watt module. Keep in mind that
with degradation accounted for, you will see even less limiting in future
years. I'd encourage Wrenches to look closely at the attached document. It is
based upon real system production data from Enlighten compared against actual
irradiance data.
Most analysts would agree that some "clipping" is good. You will have a better
return on your investment when your DC to AC ratio is greater than one. In
this case, bigger is better.
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org