We’ve run into the problem in MA where the electrical board suggested we cut apart Enphase trunk cable to put it in a raceway. We all know that isn’t possible.
From: RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Bill Brooks Sent: Tuesday, May 27, 2014 3:18 PM To: 'RE-wrenches' Subject: Re: [RE-wrenches] 2014 NEC Nick and Jay, There is a basic problem that products are not currently available to specifically address this application. I know Enphase has done a lot of research lately about this issue, so they may have uncovered problems that were previously not known. My information is that the products are actually bi-directional devices. GFCIs are not bi-direction and can fail with voltage on the load side of the device. It is possible that some AFCIs have the same problem. This AFCI provision is a requirement that was sold to UL and the Code Making Panel with the assurance from a very large breaker manufacturer that developing products for this application was simple and straightforward. That manufacturer has not stepped forward with a product and so we find ourselves in 90.4 land (use the previous version of the code). Some AHJs have chosen not to read it that way and have been requiring micro-inverter systems to be installed raceways (even though not compatible with raceways). NFPA likely have to issue an official interpretation on this since it is unclear whether a product will be developed in the reasonable future. Bill. From: RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Jay Peltz Sent: Tuesday, May 27, 2014 11:32 AM To: RE-wrenches Subject: Re: [RE-wrenches] 2014 NEC Hi nick Good to know, I was told this by bill brooks at a training a few months ago. Jay Sent from my iPhone On May 27, 2014, at 9:00 AM, Nick Soleil <nsol...@enphaseenergy.com<mailto:nsol...@enphaseenergy.com>> wrote: Hi Jay, It is not acceptable to wire the AFCI breaker with the utility power on the output of the AFCI breaker. That does not meet the specifications for the AFCI breakers. These breakers are sensitive to having voltage on their output when the breaker is opened, which can damage the AFCI breakers. Currently, there are no AFCI circuit breakers that are listed for back-feed. On Tue, May 20, 2014 at 8:10 AM, jay peltz <j...@asis.com<mailto:j...@asis.com>> wrote: HI Will, You can do this. Take a standard breaker panel, install a Arc fault and run the wiring from the enphase like it is the grid: ie into the main lugs. Then this will go out through the breaker in the correct fashion, and onto the main panel. jay peltz power PS as to the code, they want it this way On May 20, 2014, at 7:59 AM, Will White wrote: Wrenches, Is anyone else having problems with inspectors and the 2014 NEC? In Mass we’re having all kinds of issues with inspectors requiring/allowing an array of different things for 690.12 rapid shut down ranging from roof top disconnects, disconnects on the side of a house 20’ up, disconnects in attics, or only disconnects that can be activated on the ground. It varies between inspectors. We’re also having problems with one inspector requiring arc fault breakers on Enphase even though there are no UL listed arc fault breakers that can be back fed or he wants us to run the trunk cable in a raceway. It’s getting very difficult to install in Mass. Thanks, Will Will White Operations Manager - New England RGS Energy 64 Main St. |Montpelier, VT 05602 tel 802.223.7804<tel:802.223.7804> | mobile 802.234.3167<tel:802.234.3167> | fax 802.223.8980<tel:802.223.8980> RGSEnergy.com<http://www.rgsenergy.com/> | william.wh...@rgsenergy.com<mailto:william.wh...@rgsenergy.com> _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org<mailto:RE-wrenches@lists.re-wrenches.org> Change email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm<http://www.re-wrenches.org/etiquette.htm> Check out participant bios: www.members.re-wrenches.org<http://www.members.re-wrenches.org> _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org<mailto:RE-wrenches@lists.re-wrenches.org> Change email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm<http://www.re-wrenches.org/etiquette.htm> Check out participant bios: www.members.re-wrenches.org<http://www.members.re-wrenches.org> -- Cordially, Nick Soleil Field Applications Engineer Enphase Energy Mobile: (707) 321-2937 <http://enphase.com/enlighten_content/myenlighten-launch-site/?utm_source=MyEnlightenPromo&utm_medium=Email_Sig&utm_campaign=MyEnlighten> MyEnlighten is Coming. Get Ready<http://enphase.com/enlighten_content/myenlighten-launch-site/?utm_source=MyEnlightenPromo&utm_medium=Email_Sig&utm_campaign=MyEnlighten> <http://www.enphase.com/commercial?utm_source=email&utm_medium=sig&utm_campaign=Comm2012> 1420 North McDowell Petaluma, CA 94954 www.enphase.com<http://www.enphaseenergy.com/> P: (707) 763-4784 x7267 F: (707) 763-0784 E: nsol...@enphaseenergy.com<mailto:nsol...@enphaseenergy.com> NABCEP Certified Solar PV Installer #03262011-300 California C10 Licensed Electrician #986315 Texas Master Electrician #284451 “Don’t get me wrong: I love nuclear energy! It’s just that I prefer fusion to fission. And it just so happens that there’s an enormous fusion reactor safely banked a few million miles from us. It delivers more than we could ever use in just about 8 minutes. And it’s wireless!” - William McDonough This email message is for the sole use of the intended recipient(s) and may contain confidential and/or privileged information. If you are not an intended recipient, you may not review, use, copy, disclose or distribute this message. If you received this message in error, please contact the sender by reply email and destroy all copies of the original message. _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org<mailto:RE-wrenches@lists.re-wrenches.org> Change email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm<http://www.re-wrenches.org/etiquette.htm> Check out participant bios: www.members.re-wrenches.org<http://www.members.re-wrenches.org> ________________________________ [http://static.avast.com/emails/avast-mail-stamp.png]<http://www.avast.com/> This email is free from viruses and malware because avast! Antivirus<http://www.avast.com/> protection is active.
_______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Change email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org