Jeremy,
Without digging into the specs on the Ideal connectors, I doubt that they will work with fine-stranded wire. The problem with these types of connectors is that the set screw that you turn to tighten the connection is in direct contact with the wire strands. As you tighten it, it rubs the strands in a circular motion, which will stretch, flatten, and tear the strands. It would work fine if you use ferrules, but not without them. Terminals that are rated for direct use with fine-stranded wire would have a clamping-type terminal, where the screw used to tighten the connection pushes down on a solid piece of metal which then clamps the wire. Even in this case, it may still not be approved for fine-stranded wire depending on its design. The Buchanan splices should be fine. They are basically the same as a ferrule, except that they are crimped with a crimping tool instead of the pressure from tightening a screw in a bus bar. The crimping tool is not in direct contact with the wire strands, so there is no tearing or other damage to the wire. However, the spec sheet does not specify the acceptable wire types, and I can’t seem to find anything with a Google search. It might be worth contacting Buchanan/Ideal to see if they have better info. Brian Teitelbaum AEE Solar *From:* RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] *On Behalf Of *Jeremy Rodriguez *Sent:* Wednesday, August 10, 2016 6:32 PM *To:* RE-wrenches *Subject:* Re: [RE-wrenches] Pass through/transition box for Enphase How about these? https://idealind.com/us/en/products/wire-termination/set-screw-connectors/set-screw-connectors/set-screw-wire-connectors.aspx Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On Aug 8, 2016, at 2:00 PM, Benn Kilburn <b...@skyfireenergy.com> wrote: Din rail mounted terminal blocks.... Weidmuler WDU6 or WDU10, depending on the wire size you are using. Benn Kilburn SkyFire Energy Inc. 780-906-7807 On Aug 8, 2016, at 12:49 PM, Jason Szumlanski < ja...@floridasolardesigngroup.com> wrote: I'm looking to bring 8 Enphase 240V circuits in multiple conduits into an enclosure inside the attic where I can transition to Romex. I'd rather use some kind of rail mounted terminals in an enclosure or something rather than making splices in a generic j-box. I'm not looking to combine circuits - just transition from THWN to Romex and keep things neat an organized. Any suggestions? Jason Szumlanski _______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org _______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org