Hi drake I did a small enphase system with my 3524vfx some years ago. It was 3 M190’s.
It had the same issues. Mostly it appeared during when the loads vs AC production were at a specific level If the AC was high and loads low, it was fine. If the ac low and loads high no issue But if they were close then I’d get the pulsing you are talking about. I don’t have a scope, best guess is its harmonics. I didn’t like the pulsing and thought that it’s bad for compressors, lights, etc so I stopped using it. I don’t know if is something specific to older vfx units or emphase or? I would take it off line Jay Peltz power. > On Aug 25, 2020, at 8:34 AM, drake.chamber...@redwoodalliance.org wrote: > > > The inverter is set to ON not to SEARCH. If the Enphase circuit is switched > off, the pulsing stops immediately. This system has both AC and DC coupling. > > In another location, with a Sunny Boy AC coupled with a pair of stacked > VFX3524 inverters, there is some pulsing in low light conditions. The Radian > and Enphase combo is much more noticeable. > > --- > > > >> On 2020-08-25 10:42, Jerry Shafer wrote: >> >> Wrenches >> I would think that in time there might be damage. Check to make sure the >> inverter is not on search but I stead "ON", next if you turn off the enphase >> the the outback perform normally. Check the inverter frequency to see your >> frequency is shifting have one that has both AC & DC Coupling and no issues. >> >> On Tue, Aug 25, 2020, 6:37 AM <drake.chamber...@redwoodalliance.org> wrote: >> Hello Wrenches, >> >> An AC coupled arrangement, with an 8 kW Radian and 8 Enphase >> microinverters, pulses lighting at low levels of array illumination. >> This is generally not too much of a problem. >> >> Under certain levels of solar isolation, the pulsing becomes extreme and >> causes the motors in the refrigerator and air-conditioner to pulse, >> sometimes causing very audible vibrations. >> >> Will this harm the appliances? Is there anything that can be done to >> moderate or stop the pulsing? >> >> Thank you, >> >> Drake >> Athens Electric LLC >> >> -- >> _______________________________________________ >> List sponsored by Redwood Alliance >> >> List Address: RE-wrenches@lists.re-wrenches.org >> >> Change listserver email address & settings: >> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >> >> List-Archive: >> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org >> >> List rules & etiquette: >> www.re-wrenches.org/etiquette.htm >> >> Check out or update participant bios: >> www.members.re-wrenches.org >> >> >> _______________________________________________ >> List sponsored by Redwood Alliance >> >> List Address: RE-wrenches@lists.re-wrenches.org >> >> Change listserver email address & settings: >> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >> >> List-Archive: >> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org >> >> List rules & etiquette: >> www.re-wrenches.org/etiquette.htm >> >> Check out or update participant bios: >> www.members.re-wrenches.org >> > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org >
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
