[EMAIL PROTECTED] wrote:
>> make[1]: Entering directory `/usr/local/src/sane-0.72/backend'
>> gcc -c -I/usr/X11R6/include -I/usr/lib/glib/include -g -O2 -Wall
>> -DHAVE_CONFIG_H -I. -I. -I../include -I../include
>> -I/usr/X11R6/include -I/usr/lib/glib/include -D_GNU_SOURCE
>> -DPATH_SANE_CONFIG_DIR=/usr/local/etc/sane.d
>> -DPATH_SANE_DATA_DIR=/usr/local/share!
>> -DV_MAJOR=0 -DV_MINOR=72 -DBACKEND_NAME=umax -DLIBDIR=/usr/local/lib
>> -fPIC -DPIC umax.c
>> umax.c: In function `sane_umax_set_io_mode':
>> umax.c:5083: parse error at null character
>> umax.c:5084: warning: control reaches end of non-void function
>> make[1]: *** [umax.lo] Error 1
>> make[1]: Leaving directory `/usr/local/src/sane-0.72/backend'
>> make: *** [all-recursive] Error 1
> Hmmm, I'm not sure. Sounds like the file is corrupted (if I had
> to guess). If it were me, I would delete the source tree and try
> re-extracting the tar file. Your configure output matched mine
> FWIW.
I done that twice already but it did not solve the problem. The error
happen in the same place both times after re-extracting the tar file.
>>Anyway, I don't understand what is causing the compile error with the
>>umax.c part of SANE. The only scanners that I have, is a Hewlett Packard
>>4c flatbed and a Connectix QuickCAM.
> Sane compiles all the backends even for hardware you may not have
> since it doesn't make any attempt at compile time to detect hardware.
OK.
>On Fri, 1 May 1998 [EMAIL PROTECTED] wrote:
>>OK, I have installed gtk+-0.99.10, which I downloaded from the
>>RedHat ftp site a few days ago. I removed the old gtk-0.99.xxxx
>>that came with RedHat Linux 5.0 so the control-panel is disabled
>>now.
>You should get gtk+ 1.0 rpms from ftp.gimp.org since that is the
>official stable release.
>jason
I just download the new gtk+-1.0.0-1.rpm and installed it and I was able to
finally compile SANE-0.72-1 completely. It works great with my Hewlett
Packard ScanJet 4c flatbed scanner. However, with the Connectix Color
QuickCAM, it takes one frame and freezes for some reason. I have to kill the
xcam process to get out of it. The QuickCAM is connected to the lp1 (0x378
IRQ 11) parallel port. I have tried changing the config.qcam file from 0x378
to u0x378 but that did not solve the problem. Then I tried connecting the
QuickCAM to the lp0 (0x3BC IRQ 7) parallel port where I had my LaserJet II
printer connected and changed the config.qcam file from 0x3BC to u0x3BC
but xcam still froze. I would like to use the QuickCAM on the lp1 (0x378
IRQ 11) parallel port so I can have the LaserJet II printer connected to
lp0.
Do I have to modify the kernel and/or lp driver module to use IRQ 11 for
lp1?
Thank you again for helping me.
David Smith
Net-Tamer V 1.09.2 - Registered
--
PLEASE read the Red Hat FAQ, Tips, Errata and the MAILING LIST ARCHIVES!
http://www.redhat.com/RedHat-FAQ /RedHat-Errata /RedHat-Tips /mailing-lists
To unsubscribe: mail [EMAIL PROTECTED] with
"unsubscribe" as the Subject.