On Fri, 27 Sep 2002 21:34:57 -0400
Tom Pollerman <[EMAIL PROTECTED]> wrote:

> On Fri, 27 Sep 2002 14:54:01 -0600
> "Ashley M. Kirchner" <[EMAIL PROTECTED]> wrote:
> 
> > Tom Pollerman wrote:
> > 
> > >   If you haven't tired this already, you may try adding the
> > >   'options'
> > > line to your /etc/modules.conf.
> > >
> > >                alias scsi_hostadapter aha1542
> > >                options aha1542 aha1542=0x330,10,7
> > 
> >     No dice.  Same error while trying to boot up with a stock
> >     kernel:
> > 
> > Loading scsi_mod module
> > SCSI subsystem driver Revision: 1.00
> > Loading sd_mod module
> > kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno
> > = 2 Loading aha1542 module
> > Unable to determine Adaptec DMA priority.  Disabling board
> > /lib/aha1542.o: init_module:
> > Hint: insmod errors can be caused by incorrect module parameters,
> > including invalid IO or IRQ parameters
> > ERROR: /bin/insmod exited abnormally!
> > 
> >     And it never loads.
> > 
> > 
> >     Something else I'm noticing with this too.  When I boot up
> >     with my compiled
> > kernel, everything works.  System comes up, works, everyone's
> > happy.
> >  Then I
> > try to use the stock kernel and get the above SCSI error.  So I go
> > back to my stock kernel and suddenly I'm faced with this:
> > 
> > EXT2-fs: ide0(3,1): couldn't mount because of unsupported optional
> > features(4).
> > Kernel panic: VFS: Unable to mount root fs on 03:01
> > 
> >     The only way to "recover" from this is to boot up from the
> >     install CD into
> > rescue mode, and just exiting (rebooting) again.  Then my kernel
> > works again. So, the stock kernel must be changing something
> > that's causing this.  Problem is, I don't have a clue.
> > 
> >     Anyone have any ideas?
> > 
>   I checked RH6, RH7, and RH7.3 manuals. They all give the same
> example as a SCSI parameter for the AHA 1542:
> 
>                                    bases=0x330
> 
> for an AHA1542 at port 330
> 
> 

   One final thought on this...In my search to get my aha1542 to
install, I ran across this:

FROM:

http://www.hh.net/RedHat/RedHat-FAQ-3.html#ss3.8


3.8 Why doesn't my Adaptec 154x work?

"It appears that some 1540's and 1542's are a bit hosed by the
Buslogic probe. You will usually get an error referring to ``DMA'' in
the Adaptec probe when this happens. To fix it, you need to enter
command line parameters as follows: 

       boot:  linux aha154x=0x340 buslogic=0x334

This is assuming, of course, that the base address of your Adaptec is
0x340. If not, put your address in there instead. This will force the
buslogic to only probe an address where your Adaptec is not."

   It seems that the kernel scans for a Buslogic card first and then
the Adaptec, which can confuse some 1542's. It could be that you have
one of these.

                                                Regards,

                                                 Tom



-- 
redhat-list mailing list
unsubscribe mailto:[EMAIL PROTECTED]?subject=unsubscribe
https://listman.redhat.com/mailman/listinfo/redhat-list

Reply via email to