Thanks Randy for that additional information. Eric, I stand corrected, the part number you gave me is correct. However, I simply need the top sway bracket not the complete side mount kit. I will call Wisco tomorrow to see if they would sell me just the top bracket.
Does anyone have a top sway bracket that they can offer me? Thanks... --- In Repeater-Builder@yahoogroups.com, "Yahoo" <ya...@...> wrote: > > DB5004S-MTD > > Jeff > > -----Original Message----- > From: Repeater-Builder@yahoogroups.com > [mailto:repeater-buil...@yahoogroups.com] On Behalf Of n2len > Sent: Saturday, April 25, 2009 5:16 PM > To: Repeater-Builder@yahoogroups.com > Subject: [Repeater-Builder] Re: RFS PD220-N Question Regarding Mounting > Clamps > > Hello Eric, > Sorry I wrote the incorrect model. It's the PD220-2. > > The side mount part number you gave me is not what I am looking for. What I > need is the top insulated support mount. I can't find it unless I am missing > it somewhere. Telewave sells a similar product which I guess I can > substitute it if I can find a RFS equivalent. > > Here is the link for the Telewave ANTM432 > > http://www.telewave.com/pdf/TWDS-7046.pdf > > > --- In Repeater-Builder@yahoogroups.com, "Eric Lemmon" <wb6fly@> wrote: > > > > Len, > > > > I'm not sure what a "PD220-N" antenna is, since the PD220 antennas > > listed in my Celwave catalog have a digit after the hyphen. Anyway, > > the side mount kit for a PD220 antenna is the PD503. It is adjustable > > to mount the antenna between 6" and 7' away from the tower. The PD556 > > is a shorter version that is limited to an offset of 3'. Both of > > these kits mount on tower legs up to 2.375" diameter. There are other > > kits for larger leg diameters, up to six inches. > > > > -----Original Message----- > > From: Repeater-Builder@yahoogroups.com > > [mailto:repeater-buil...@yahoogroups.com] On Behalf Of n2len > > Sent: Saturday, April 25, 2009 1:48 PM > > To: Repeater-Builder@yahoogroups.com > > Subject: [Repeater-Builder] RFS PD220-N Question Regarding Mounting > > Clamps > > > > > > > > Maybe someone can give me a specific part number to order. I just > > purchased a RFS PD220-N to be mounted on a Rohn 45 at the 170 foot > > level. (190 total to the top) I will be replacing this antenna with a > > Brand New Comtelco BSLL150-XL3 which has performed horribly. What a > > BIG MISTAKE! > > Here is my question: We currently have a lower base dual side arm > > bracket mount that slides in and out from the tower with a small > > vertical pole for the bottom brackets for the base of the antenna. > > What are the correct upper insulated side mounts to protect the antenna > from swaying in the wind? > > RFS PART NUMBER? > > How many are actually needed? > > Are they ordered by length or are they adjustable like the lower base arm? > > We can top mount the antenna, however I dont want the antenna to crack > > from the winter wind and severe ice in the NYS mountains. > > > > Also, There are 2 towers the same height at this site. Literally right > > next to each other. Should it make a dirrerence in polarization if the > > top of the antenna clears the top of the tower? > > > > Should we make the tip clear or not? > > > > Input needed.... > > > > Warm Regards, > > Len N2LEN > > > > > > > ------------------------------------ > > > > Yahoo! Groups Links >