If an interface in IOS is configured and not in Shutdown or testing the .1.3.6.1.2.1.2.2.1.7.x (ifAdminStatus) will show UP
If you are wondering what mibs are supported by what versions of IOS you can go to http://tools.cisco.com/Support/SNMP/do/MIBSupport.do?local=en&step=3 Or http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en to translate OID's -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Dirk Bulinckx Sent: Thursday, November 03, 2005 3:21 PM To: salive@woodstone.nu Subject: RE: [SA-list] Cisco question In the mib file it says .1.3.6.1.2.1.2.2.1.7.x (ifAdminStatus) The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. .1.3.6.1.2.1.2.2.1.8.x (ifOperStatus) The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. So what you're saying is that when a serial should be up (configured to be up) and it's down due to a line issue that both .1.3.6.1.2.1.2.2.1.7.x and .1.3.6.1.2.1.2.2.1.8.x will show a down? I would expect that the .7.x would show an UP (as that is what we desire) and .8.x would show DOWN (as that is the reality due to the line being down) Dirk. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jason Passow Sent: Thursday, November 03, 2005 9:13 PM To: salive@woodstone.nu Subject: Re: [SA-list] Cisco question This is somewhat true except when you say the desired state and operational state. .1.3.6.1.2.1.2.2.1.7.x is the state of the itnerface itself and .1.3.6.1.2.1.2.2.1.8.x is the state of the line. Most of the time (at least on private lines) when the network is down both show down. Of course it depends on the nature of the problem. It is certainly possible for the line to be down and the interface to be up. Therefore you cannot compare .1.3.6.1.2.1.2.2.1.7.x to .1.3.6.1.2.1.2.2.1.8.x and get anything useful other than the nature of the down condition. When those ids are 1 they are up and when they are 2 they are down. ( There are also other integers for the interface being turned off etc. but those are the two important ones). Jason Passow Mississippi Welders Supply [EMAIL PROTECTED] ph: (507) 494-5178 fax: (507) 454-8104 "If you do everything right, nobody will realize you've done anything at all." Dirk Bulinckx wrote: > A question for the Cisco guru's on the list :-) > > Is the below info correct for 'all' cisco routers? > > .1.3.6.1.2.1.2.1.0 give the number of interfaces > > > .1.3.6.1.2.1.2.2.1.2.x gives the description of the different > interface (x max of number of interfaces) > > > .1.3.6.1.2.1.2.2.1.7.x gives the desired state of the interface > .1.3.6.1.2.1.2.2.1.8.x gives the operational state of the interface > > > Based on this is it correct that > IF > .1.3.6.1.2.1.2.2.1.7.x <> .1.3.6.1.2.1.2.2.1.8.x > THEN > interface is not in the state it should be? > > > > >From what I can see this seems correct for a 2501 and 4500, but I > >wonder if > this is correct for other IOS based routers (like a 3725) > > > Dirk. > > > To unsubscribe from a list, send a mail message to [EMAIL PROTECTED] With the following in the body of the message: unsubscribe SAlive To unsubscribe from a list, send a mail message to [EMAIL PROTECTED] With the following in the body of the message: unsubscribe SAlive To unsubscribe from a list, send a mail message to [EMAIL PROTECTED] With the following in the body of the message: unsubscribe SAlive
