Allan, What does that mean? Do I have to manually clean out the conf files before installing? On Mar 7, 2015 1:18 PM, "m. allan noah" <kitno...@gmail.com> wrote:
> sane does not overwrite your already installed config files. > > allan > > On Sat, Mar 7, 2015 at 3:57 AM, Rafe DiDomenico <rafe...@gmail.com> wrote: > > Thanks again Paul, > > > > So, running the first check ("export SANE_DEBUG_GENESYS=10") returns > > nothing. > > > > I checked the genesys.conf and find no mention of the 220 in there. > > > > I checked the git folder and "pull" says it's "already up-to-date." > > > > I must not have the newest backend for some reason (I used > > git://git.debian.org/sane/sane-backends.git). Is the genesys backend not > > responding a problem, or is that just because it's not using it? > > > > > > > > On 03/06/2015 07:52 PM, Paul Newall wrote: > > > > On 06/03/15 09:44, Rafe DiDomenico wrote: > > > > Just for fun, I rebooted and tried everything again. Now I get: > > > > rafe@office:~$ find /usr -name libsane.s* > > > > /usr/lib/libsane.so.1.0.25 > > /usr/lib/x86_64-linux-gnu/libsane.so.1.0.25 > > /usr/lib/x86_64-linux-gnu/libsane.so.1.0.24 > > /usr/lib/x86_64-linux-gnu/libsane.so > > /usr/lib/x86_64-linux-gnu/libsane.so.1 > > /usr/lib/libsane.so > > /usr/lib/libsane.so.1 > > > > So it is in x86... > > Find-scanner identifies the scanner, but still getting no further. > > > > found USB scanner (vendor=0x04a9 [Canon], product=0x190f [CanoScan], > > chip=GL848+) at libusb:002:002 > > # Your USB scanner was (probably) detected. It may or may not be > supported > > by > > # SANE. Try scanimage -L and read the backend's manpage. > > > > # Not checking for parallel port scanners. > > > > # Most Scanners connected to the parallel port or other proprietary > ports > > # can't be detected by this program. > > > > rafe@office:~$ sudo scanimage -L > > > > No scanners were identified. If you were expecting something different, > > check that the scanner is plugged in, turned on and detected by the > > sane-find-scanner tool (if appropriate). Please read the documentation > > which came with this software (README, FAQ, manpages). > > > > > > > > > > > > rafe, > > So I'd say your current situation is that you have sane installed in a > > couple of places (usr/lib and usr/lib/x86_64-linux-gnu) > > and you are running a version of 1.0.25 > > I think the genesys backend is supposed to support your lide 220 > scanner, so > > I'd now do this in terminal: > > ...$ export SANE_DEBUG_GENESYS=10 > > ...$ scanimage -L > > the first line causes the genesys backend to output debug information > when > > you run scanimage, a higher number gives more detail. > > So you should see some debug info as scanimage looks for the scanner. (If > > you see nothing the genesys backend is probably not enabled) > > > > If the backend is being run by scanimage, but not finding the scanner: > > Look at the file /etc/sane.d/genesys.conf to see if it has the lines > > # Canon LiDE 220 > > usb 0x04a9 0x190f > > if not your version of sane may not be new enough. > > > > > > > > > > > > -- > > sane-devel mailing list: sane-devel@lists.alioth.debian.org > > http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/sane-devel > > Unsubscribe: Send mail with subject "unsubscribe your_password" > > to sane-devel-requ...@lists.alioth.debian.org > > > > -- > "well, I stand up next to a mountain- and I chop it down with the edge > of my hand" >
-- sane-devel mailing list: sane-devel@lists.alioth.debian.org http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/sane-devel Unsubscribe: Send mail with subject "unsubscribe your_password" to sane-devel-requ...@lists.alioth.debian.org