[OSL | CCIE_Voice] GK Call getting busy tone
Hi Experts: When I redial a HQ missed call (+1408XXX) on Br2 Ph1 (International) , HQ Phone is recieving the call, I am able to pickup but in few seconds I get fast busy tone on Br2 Ph1. Path is as follows: Br1 Ph1 - Br1 RTR RAS - CUCM Xlation to 9XXX - HQ local GW - HQ Ph1 I also added IOS Xcoder on Gatekeeper trunk. Still same. Please advice .. T I A Shrini ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] GK Call getting busy tone
On the GK Trunk in CUCM, uncheck Wait for Far End H.245 Terminal Capability Set On 18 November 2010 11:44, Shrini linuxbos...@gmail.com wrote: Hi Experts: When I redial a HQ missed call (+1408XXX) on Br2 Ph1 (International) , HQ Phone is recieving the call, I am able to pickup but in few seconds I get fast busy tone on Br2 Ph1. Path is as follows: Br1 Ph1 - Br1 RTR RAS - CUCM Xlation to 9XXX - HQ local GW - HQ Ph1 I also added IOS Xcoder on Gatekeeper trunk. Still same. Please advice .. T I A Shrini ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] I'm praticing Globized and localized call routing but I think there may be a mistake on the PSTN router/phone
Volume 2 LAb 4, I'm praticing Globized and localized call routing but I think there may be a mistake on the PSTN Router/Phone Router here is an IDSN Q931 output I dial from the PSTN phone Line 2 HQ-NYC +1212 394 2123 3945002 Which is HQ phone 2 Ext 5002 (this is a local call). Nov 18 10:47:47.102: ISDN Se0/0/0:23 Q931: RX - SETUP pd = 8 callref = 0x009B Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Calling Party Number i = 0x4180, '2123942123' Plan:ISDN, Type:Subscriber(local) Called Party Number i = 0xA1, '2123945002' Plan:ISDN, Type:National Nov 18 10:47:47.130: ISDN Se0/0/0:23 Q931: TX - CALL_PROC pd = 8 callref = 0x809B The R1 Gateway is mgcp Why does the calling party show up as Calling Party Number i = 0x4180, '2123942123'? Is that not a national number? I thought it should show up as 7 digits 3942123 as subscriber and then Called Party Number i = 0xA1, '2123945002' Plan:ISDN, Type:National I'm making a local call not a national call. why is it appearing as 10 digits and national Am I wrong or is the PSTN presenting me with the wrong information? Regards Mike ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Lab 3B troubleshooting problem
Hi guys, Yesterday when I was in the lab I had a problem like that. In CME sccp phones had SIP firmwire which I corrected by registering them to CUCM as SCCP (I followed the way which Matthew and Chevy said). There was no problem with SCCP phones. However, one of the SIP phones (7960-directly connected) registered as SCCP. I followed the same way, changed option 150 ip address from CME to CUCM. I registered it as SIP phone to CUCM so it got the correct firmwire. All good. But when I try to re-register it to CME it didnt. What did I miss? (source address in voice register global was correct, sip and bind all source int commands were correct, voice register dn and voice register pool commands were ok. Xlite was registered but 7960 directly connected phone didnt) Kind regards, -- Dew Swen / sent from mobile device CCVP, CCDP, CCNP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Home Lab Via ASA to the IP Expert Lab
Hello everyone, I need to configure my ASA (instead of the norm of using the EZVPN via a router) to the IPExpert Lab Rack so that I can register my home phones. Has anyone been able to do this successfully and can share some info on how to achieve the same? Regards, Rohan ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] GK Call getting busy tone
Hi Roger, I tried as suggested by you. No luck, still same. Thanks Shrini On 11/18/2010 2:18 AM, Rogers Ochieng wrote: On the GK Trunk in CUCM, uncheck Wait for Far End H.245 Terminal Capability Set On 18 November 2010 11:44, Shrini linuxbos...@gmail.com mailto:linuxbos...@gmail.com wrote: Hi Experts: When I redial a HQ missed call (+1408XXX) on Br2 Ph1 (International) , HQ Phone is recieving the call, I am able to pickup but in few seconds I get fast busy tone on Br2 Ph1. Path is as follows: Br1 Ph1 - Br1 RTR RAS - CUCM Xlation to 9XXX - HQ local GW - HQ Ph1 I also added IOS Xcoder on Gatekeeper trunk. Still same. Please advice .. T I A Shrini ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] BR2-rtr- keep getting memory buffer leaking
Experts, does anyone run in to following error on proctorlabs br2-rtr router. Pool: Processor Free: 1442660 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= CC-API_VCM, ipl= 0, pid= 305, -Traceback= 0x418DEBD8 0x4011E8EC 0x40124934 0x40124F04 0x42570FFC 0x4257E0A0 0x4257E154 0x42591154 0x4158A7BC I can post my config as I was told by support that this might be to do with my config. thank you ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 3B troubleshooting problem
Hi Shrini, yes I wrote the id mac correctly. I entered create profile command every time I changed the configuration. But I didnt wrote no create profile. Does it make sense? On 11/18/10, Shrini linuxbos...@gmail.com wrote: Have you specified id mac under voice register pool of the phone ? Under voice register global no create profile create profile This should work as long as all config is good. On 11/18/2010 7:10 AM, dew.s...@gmail.com wrote: Hi guys, Yesterday when I was in the lab I had a problem like that. In CME sccp phones had SIP firmwire which I corrected by registering them to CUCM as SCCP (I followed the way which Matthew and Chevy said). There was no problem with SCCP phones. However, one of the SIP phones (7960-directly connected) registered as SCCP. I followed the same way, changed option 150 ip address from CME to CUCM. I registered it as SIP phone to CUCM so it got the correct firmwire. All good. But when I try to re-register it to CME it didnt. What did I miss? (source address in voice register global was correct, sip and bind all source int commands were correct, voice register dn and voice register pool commands were ok. Xlite was registered but 7960 directly connected phone didnt) Kind regards, -- Dew Swen / sent from mobile device CCVP, CCDP, CCNP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com -- Sent from my mobile device *--* *Dew Swen CCVP, CCDP, CCNP * ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 3B troubleshooting problem
Hi Dew, 1. no create profile create profile After you add DNs and pools run create profile again under global. 2. debug tftp events rese the phone and see what it is requesting and is it succeeding. Else finally In the flash: you see below files. 6 3579 Apr 01 2002 16:18:18 softkeyDefault_kpml.xml 7 3613 Apr 01 2002 16:18:20 softkeyDefault.xml 8 69 Apr 01 2002 16:18:18 syncinfo.xml 9 1836 Apr 01 2002 16:18:18 SIPDefault.cnf 101236 Mar 01 2002 20:14:38 SIP000D659FDBD8.cnf 11 13 Apr 01 2002 16:15:46 OS79XX.TXT Delete them. Go to global run create profile, it will create these files again with new info. more flash:SIP000D659FDBD8.cnf more flash:SIPDefault.cnf Above two are also helpful to identify the problem. Also check #sh ephone See if the phone is registered as ephone. If yes , no ephone XX shut down the phone port reload the router. On 11/18/2010 1:21 PM, Dew Swen wrote: Hi Shrini, yes I wrote the id mac correctly. I entered create profile command every time I changed the configuration. But I didnt wrote no create profile. Does it make sense? On 11/18/10, Shrinilinuxbos...@gmail.com wrote: Have you specified id mac under voice register pool of the phone ? Under voice register global no create profile create profile This should work as long as all config is good. On 11/18/2010 7:10 AM, dew.s...@gmail.com wrote: Hi guys, Yesterday when I was in the lab I had a problem like that. In CME sccp phones had SIP firmwire which I corrected by registering them to CUCM as SCCP (I followed the way which Matthew and Chevy said). There was no problem with SCCP phones. However, one of the SIP phones (7960-directly connected) registered as SCCP. I followed the same way, changed option 150 ip address from CME to CUCM. I registered it as SIP phone to CUCM so it got the correct firmwire. All good. But when I try to re-register it to CME it didnt. What did I miss? (source address in voice register global was correct, sip and bind all source int commands were correct, voice register dn and voice register pool commands were ok. Xlite was registered but 7960 directly connected phone didnt) Kind regards, -- Dew Swen / sent from mobile device CCVP, CCDP, CCNP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Self terminating PRI using VRF aware h323. Is it possible
Hello Group, I am working on getting a home lab setup to practice for the IE voice lab. I have almost enough equipment to setup all 3 sites with the exception of the 4 router to either run the PSTN or Branch site. I have plenty of DSPs and MFT voice cards but short 1 router. I am researching if it is possible to utilize VRFs to configure a router as Branch site and PSTN by self terminating a back-to-back PRI. Just wondering if anyone else has set this up or researched if it is possible. Thanks for any input, Joel ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] GK Call getting busy tone
Is it a SIP or SCCP phone that you are dialing from? Have you tried to add a MTP to help w/ supp signaling? On Thu, Nov 18, 2010 at 2:08 PM, Shrini linuxbos...@gmail.com wrote: Hi Roger, I tried as suggested by you. No luck, still same. Thanks Shrini On 11/18/2010 2:18 AM, Rogers Ochieng wrote: On the GK Trunk in CUCM, uncheck Wait for Far End H.245 Terminal Capability Set On 18 November 2010 11:44, Shrini linuxbos...@gmail.com wrote: Hi Experts: When I redial a HQ missed call (+1408XXX) on Br2 Ph1 (International) , HQ Phone is recieving the call, I am able to pickup but in few seconds I get fast busy tone on Br2 Ph1. Path is as follows: Br1 Ph1 - Br1 RTR RAS - CUCM Xlation to 9XXX - HQ local GW - HQ Ph1 I also added IOS Xcoder on Gatekeeper trunk. Still same. Please advice .. T I A Shrini ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 3B troubleshooting problem
This may sound elementary but it has caught me before. Make sure you don't have auto-reg-ephone enabled on telephony-service. On Thu, Nov 18, 2010 at 3:48 PM, Shrini linuxbos...@gmail.com wrote: Hi Dew, 1. no create profile create profile After you add DNs and pools run create profile again under global. 2. debug tftp events rese the phone and see what it is requesting and is it succeeding. Else finally In the flash: you see below files. 6 3579 Apr 01 2002 16:18:18 softkeyDefault_kpml.xml 7 3613 Apr 01 2002 16:18:20 softkeyDefault.xml 8 69 Apr 01 2002 16:18:18 syncinfo.xml 9 1836 Apr 01 2002 16:18:18 SIPDefault.cnf 101236 Mar 01 2002 20:14:38 SIP000D659FDBD8.cnf 11 13 Apr 01 2002 16:15:46 OS79XX.TXT Delete them. Go to global run create profile, it will create these files again with new info. more flash:SIP000D659FDBD8.cnf more flash:SIPDefault.cnf Above two are also helpful to identify the problem. Also check #sh ephone See if the phone is registered as ephone. If yes , no ephone XX shut down the phone port reload the router. On 11/18/2010 1:21 PM, Dew Swen wrote: Hi Shrini, yes I wrote the id mac correctly. I entered create profile command every time I changed the configuration. But I didnt wrote no create profile. Does it make sense? On 11/18/10, Shrini linuxbos...@gmail.com linuxbos...@gmail.com wrote: Have you specified id mac under voice register pool of the phone ? Under voice register global no create profile create profile This should work as long as all config is good. On 11/18/2010 7:10 AM, dew.s...@gmail.com wrote: Hi guys, Yesterday when I was in the lab I had a problem like that. In CME sccp phones had SIP firmwire which I corrected by registering them to CUCM as SCCP (I followed the way which Matthew and Chevy said). There was no problem with SCCP phones. However, one of the SIP phones (7960-directly connected) registered as SCCP. I followed the same way, changed option 150 ip address from CME to CUCM. I registered it as SIP phone to CUCM so it got the correct firmwire. All good. But when I try to re-register it to CME it didnt. What did I miss? (source address in voice register global was correct, sip and bind all source int commands were correct, voice register dn and voice register pool commands were ok. Xlite was registered but 7960 directly connected phone didnt) Kind regards, -- Dew Swen / sent from mobile device CCVP, CCDP, CCNP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
