RE: policy route [7:21044]
my appologies. i always presumed it worked in the same way as unix-HA... thanks for the correction steve From: Kent Hundley Reply-To: Kent Hundley To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] Date: Wed, 26 Sep 2001 13:52:32 -0400 Stephen, Your statement is incorrect. Enabling HSRP on a router does not cause the standby router to send all packets to the primary. The only things that enabling HSRP does is: 1) Enable the primary router to answer arp replies and accept/return packets for the virtual IP address (it does this by creating a virtual MAC to match the virtual IP) 2) Enable a hearbeat signal so that secondaries can takeover for the primary in the event of failure Neither of these things has any effect on the backup HSRP routers ability to forward IP packets as it normally would. You can still use the secondary HSRP router as you normally would by sending packets to its real IP. The secondary routers will forward packets sent to them based on the contents of their routing table, they will not simply send all traffic over to the primary router. I've tested this in real world scenarios before and just re-confirmed it in my lab. -Kent -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Stephen Skinner Sent: Wednesday, September 26, 2001 8:12 AM To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] i have to diasgreeevery 3 secs a pulse is sent from the active to standby.even if you have a route connected to your standbywhen thestandby gets any routed packets HSRP (which is layer 1/2) will send it to the active master..this wil then route the packets accordingly... i`m told ther is a way around this but you will have to search the archives...it was only a couple of weeks ago Cheers steve From: Jim Bond Reply-To: Jim Bond To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] Date: Tue, 25 Sep 2001 17:15:07 -0400 I have to disagree. The standby router has static route point to the other side. Once traffic gets to standby, it should route... Jim --- Liang Mark J Civ AFRL/PROI wrote: Standby is stanby, it doesn't do any routing until the active router goes down. Regards, Mark, -Original Message- From: Jim Bond [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 25, 2001 11:52 AM To: [EMAIL PROTECTED] Subject: policy route [7:21044] Hello, I have 2 routers running HSRP in a small office. I want SMTP traffic go through standby router so I configured policy route on active router that all SMTP traffic, send to standby router. But it doesn't work. I'm wondering if policy route will work this way? At active router: interface e0 ip address 10.1.1.2 255.255.255.0 ip policy route-map SMTP standby ip 10.1.1.1 ... route-map SMTP permit 10 match ip address 102 set ip next-hop 10.1.1.3 !standby router ethernet ... access-list 102 permit tcp any any eq 25 Thanks in advance. Jim __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com [EMAIL PROTECTED] __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=21275t=21044 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: policy route [7:21044]
i have to diasgreeevery 3 secs a pulse is sent from the active to standby.even if you have a route connected to your standbywhen thestandby gets any routed packets HSRP (which is layer 1/2) will send it to the active master..this wil then route the packets accordingly... i`m told ther is a way around this but you will have to search the archives...it was only a couple of weeks ago Cheers steve From: Jim Bond Reply-To: Jim Bond To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] Date: Tue, 25 Sep 2001 17:15:07 -0400 I have to disagree. The standby router has static route point to the other side. Once traffic gets to standby, it should route... Jim --- Liang Mark J Civ AFRL/PROI wrote: Standby is stanby, it doesn't do any routing until the active router goes down. Regards, Mark, -Original Message- From: Jim Bond [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 25, 2001 11:52 AM To: [EMAIL PROTECTED] Subject: policy route [7:21044] Hello, I have 2 routers running HSRP in a small office. I want SMTP traffic go through standby router so I configured policy route on active router that all SMTP traffic, send to standby router. But it doesn't work. I'm wondering if policy route will work this way? At active router: interface e0 ip address 10.1.1.2 255.255.255.0 ip policy route-map SMTP standby ip 10.1.1.1 ... route-map SMTP permit 10 match ip address 102 set ip next-hop 10.1.1.3 !standby router ethernet ... access-list 102 permit tcp any any eq 25 Thanks in advance. Jim __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com [EMAIL PROTECTED] __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=21161t=21044 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: policy route [7:21044]
Stephen, Your statement is incorrect. Enabling HSRP on a router does not cause the standby router to send all packets to the primary. The only things that enabling HSRP does is: 1) Enable the primary router to answer arp replies and accept/return packets for the virtual IP address (it does this by creating a virtual MAC to match the virtual IP) 2) Enable a hearbeat signal so that secondaries can takeover for the primary in the event of failure Neither of these things has any effect on the backup HSRP routers ability to forward IP packets as it normally would. You can still use the secondary HSRP router as you normally would by sending packets to its real IP. The secondary routers will forward packets sent to them based on the contents of their routing table, they will not simply send all traffic over to the primary router. I've tested this in real world scenarios before and just re-confirmed it in my lab. -Kent -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Stephen Skinner Sent: Wednesday, September 26, 2001 8:12 AM To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] i have to diasgreeevery 3 secs a pulse is sent from the active to standby.even if you have a route connected to your standbywhen thestandby gets any routed packets HSRP (which is layer 1/2) will send it to the active master..this wil then route the packets accordingly... i`m told ther is a way around this but you will have to search the archives...it was only a couple of weeks ago Cheers steve From: Jim Bond Reply-To: Jim Bond To: [EMAIL PROTECTED] Subject: RE: policy route [7:21044] Date: Tue, 25 Sep 2001 17:15:07 -0400 I have to disagree. The standby router has static route point to the other side. Once traffic gets to standby, it should route... Jim --- Liang Mark J Civ AFRL/PROI wrote: Standby is stanby, it doesn't do any routing until the active router goes down. Regards, Mark, -Original Message- From: Jim Bond [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 25, 2001 11:52 AM To: [EMAIL PROTECTED] Subject: policy route [7:21044] Hello, I have 2 routers running HSRP in a small office. I want SMTP traffic go through standby router so I configured policy route on active router that all SMTP traffic, send to standby router. But it doesn't work. I'm wondering if policy route will work this way? At active router: interface e0 ip address 10.1.1.2 255.255.255.0 ip policy route-map SMTP standby ip 10.1.1.1 ... route-map SMTP permit 10 match ip address 102 set ip next-hop 10.1.1.3 !standby router ethernet ... access-list 102 permit tcp any any eq 25 Thanks in advance. Jim __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com [EMAIL PROTECTED] __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=21184t=21044 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: policy route [7:21044]
Standby is stanby, it doesn't do any routing until the active router goes down. Regards, Mark, -Original Message- From: Jim Bond [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 25, 2001 11:52 AM To: [EMAIL PROTECTED] Subject: policy route [7:21044] Hello, I have 2 routers running HSRP in a small office. I want SMTP traffic go through standby router so I configured policy route on active router that all SMTP traffic, send to standby router. But it doesn't work. I'm wondering if policy route will work this way? At active router: interface e0 ip address 10.1.1.2 255.255.255.0 ip policy route-map SMTP standby ip 10.1.1.1 ... route-map SMTP permit 10 match ip address 102 set ip next-hop 10.1.1.3 !standby router ethernet ... access-list 102 permit tcp any any eq 25 Thanks in advance. Jim __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=21059t=21044 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: policy route [7:21044]
I have to disagree. The standby router has static route point to the other side. Once traffic gets to standby, it should route... Jim --- Liang Mark J Civ AFRL/PROI wrote: Standby is stanby, it doesn't do any routing until the active router goes down. Regards, Mark, -Original Message- From: Jim Bond [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 25, 2001 11:52 AM To: [EMAIL PROTECTED] Subject: policy route [7:21044] Hello, I have 2 routers running HSRP in a small office. I want SMTP traffic go through standby router so I configured policy route on active router that all SMTP traffic, send to standby router. But it doesn't work. I'm wondering if policy route will work this way? At active router: interface e0 ip address 10.1.1.2 255.255.255.0 ip policy route-map SMTP standby ip 10.1.1.1 ... route-map SMTP permit 10 match ip address 102 set ip next-hop 10.1.1.3 !standby router ethernet ... access-list 102 permit tcp any any eq 25 Thanks in advance. Jim __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com [EMAIL PROTECTED] __ Do You Yahoo!? Get email alerts NEW webcam video instant messaging with Yahoo! Messenger. http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=21062t=21044 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]