[Elecraft] Forsale - Pignology Pigknob
I don’t think this went through the first time, apologies if it’s a dup. I have an unused Pigknob that is excess to my needs. Includes the cables, interface board and even the pig eyes! Basically new in box, but I think I may have tried it once to make sure it worked, but it’s been so long I can’t recall. $100 including shipping to NA. I would ship elsewhere but would have to check shipping charges before committing to it. Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] any ideals who might have these?
The mic connector is the same size as SO239 or N connectors so caps for those will work, just google so239 cap 72 > On Dec 11, 2015, at 10:10 PM, KC6CNN wrote: > > I am looking for a cap of some sort that will screw on the microphone > connector on my K3 and my K2. > I just want some type of cap that will protect it from dust. > I saw a youtube video of a guy in the UK that had some type of a cap screwed > on his and it looked nice. > Any ideals of where they got those or who can make them? > Thanks > Gerald - KC6CNN > > > > > - > KC6CNN - Gerald > K1 # 0014 > K2 # 5486 > K3 # 6294 > KX3 # 757 > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/any-ideals-who-might-have-these-tp7611385.html > Sent from the Elecraft mailing list archive at Nabble.com. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k...@cox.net Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] When is mode A not mode A?
Ultimatic mode, in addition to Iambic A and B. > On Oct 22, 2015, at 6:54 PM, ae...@carolinaheli.com wrote: > > I asked for specifics so we can suggest/ask Elecraft for them and all I've > seen so far is generalities referring to emulation modes. > Why so vague? Why don't you guys just specifically ask for what you want? > > You guys are coming across as smug and arrogant. I'm sure that's not your > intent. > Ask specifically for what you want or ask Eric to close the thread. > > > Jerry Moore > CDXA, INDEXA, SKCC, Fists > AE4PB, K3S - S.N. 010324 > http://www.qrz.com/db/AE4PB > An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and > Patriotic. > > Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [K3] Remote Rig number difference?
Larry, I would call Elecraft and ask them directly, but I think the 1256 may be a typo in the earlier documents or a earlier model. The latest K3 remote manual (apr 2014) on the webside only mentions the 1258. Steve - KY7K k...@arrl.net Get OUT and play radio! > On Dec 22, 2014, at 5:23 PM, Larry - K1UO wrote: > > Thanks Mitch.. I went to the website you provided but I don’t find the RRC > 1256 units shown anywhere. The webswitches are called 1216 units. The > 1256,s listed in Elecraft manuals appear to look like 1258 units.. Maybe the > 1258's are just newer units with newer features? > > regards > Larry K1UO > > -Original Message- From: Mitch Wolfson DJØQN > Sent: Monday, December 22, 2014 6:37 PM > To: Larry - K1UO ; Elecraft Reflector > Subject: Re: [Elecraft] [K3] Remote Rig number difference? > > The 1258's are the RemoteRig RRC's required for remote operation, the > 1256's are Webswitches, a completely different product line. I use the > 1258's for my K3 remote control, as well as a 1256 for my rotor, raising > and lowering my mast and turning my SPE 2K-FA on and off. > > All this information is available on the RemoteRig web site at > http://www.remoterig.com/ and you can received detailed answers to any > questions you may have on the RemoteRig forum at > http://www.remoterig.com/forum/index.php > > 73, > Mitch DJ0QN > > Mitch Wolfson > DJØQN / K7DX > Neubiberger Str. 21, 85640 Putzbrunn > Skype: mitchwo - Home:+49 89 32152700 - Mobile:+49 172 8374436 > Echolink: 3001 - IRLP: 5378 > > On 22.12.2014 16:41, Larry - K1UO wrote: >> What is the difference between the Remote Rig number for the K3 – Twins on >> the RRC Website RRC-1258 MKII’s and the Remote Rig units for remoting the >> K3’s that are designated RRC-1256 in all the Elecraft literature? >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to dj...@arrl.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k...@cox.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KX3 case advice
I found the Condor H2O case a perfect fit for the KX3 with sidekick and cover. Not sure its large enough for the heatsink too… It has enough padding/insulation that I really don’t worry about the radio as long as the cover is on it. http://www.condoroutdoor.com/ma40h2opouch.aspx <http://www.condoroutdoor.com/ma40h2opouch.aspx> > On Dec 18, 2014, at 5:14 PM, Michael Walker wrote: > > I have to admit, I really like this setup. > > http://www.oe2atn.at/tom/gobox/ > > Mike va3mw > > > On Thu, Dec 18, 2014 at 4:45 PM, Mark Tellez wrote: >> >> I should mention that I liked the idea (at least conceptually) of the small >> molle pouch that can be attached to any other radio bag or backpack. I >> have been debating a larger standalone case (like a Pelican case) or camera >> bag (I liked the Lowe one!) but then I think about using it in the field. >> I will probably have a larger day pack so I am looking for something small >> (but protective) that can go inside said pack or be attached to the >> outside. >> >> It is very helpful to hear what others are using! Thanks for the feedback. >> >> Mark >> >> On Thu, Dec 18, 2014 at 1:55 PM, Mark Tellez wrote: >>> >>> Hello, >>> >>> I am looking for a case that will protect my KX3. I have the sidekick >>> handles and cover attached and also the Pro-Engineering heat sink. I was >>> originally hoping to use the Hazard 4 Jelly Roll case but I found out >> that >>> it is too snug (just barely) with these extra items attached. Any >>> suggestions? >>> >>> >>> >>> Mark >>> > Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] P3 Ubdate
I’ll throw in my request for Ultimatic mode too! Lest the Elecraft folks run out of things to do… :) > On Dec 5, 2014, at 9:53 PM, Don Wilhelm wrote: > > There is a big difference between "That could possibly be done" and "Yes, we > will include it at some later time" and "We have committed resources to bring > it into production in a timely manner". > > AFAIK, the P3 now has all the features and functions that are mentioned in > the advertizing and descriptions of its capabilities. > > The fact that added functions have been mentioned on this reflector, but have > not made it into the product advertizements and specifications does not mean > that the P3 is "incomplete". > > Anyone who purchased a P3 based on anything in excess of the functions > advertized at the time of purchase should not be disappointed when additional > functions are talked about but are not yet reality. > > A parallel example is my requests that the K2/K3/KX3 keying include Ultimatic > mode. I have been told in the past that it is being considered, but it has > not yet materialized. I do not think of that as making the K3 internal keyer > "incomplete" - only that other things need attention from the limited > Elecraft engineering staff than my request for Ultimatic keying. > > 73, > Don W3FPR > Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] OT: Foot swtches
IMHO the best foot switch for radio use is the M-gear SP-2. Takes very little effort to depress and has a switch to select NO or NC connection. I have 4 of them and know others that I’ve recommended them too and have not heard of a single failure. http://www.sweetwater.com/store/detail/PedalPiano?adpos=1o4&creative=55644138841&device=c&matchtype=&network=g&gclid=CKeNtcC1r8ECFUE0aQodAGEA7A On Oct 15, 2014, at 11:05 AM, David Bunte wrote: > Do check carefully... some or N.O. and others are N.C. Also, you tend to > get what you pay for... some of the lower priced ones I have seen are VERY > cheaply made, and may not hold up to a full contest weekend. > > I am probably prejudiced in favor of the very heavy duty cast foot switch I > use. In fact, almost every time I see one like it at a flea market, I buy > it, clean it up, put a new cable on it and re-sell it. I currently have > just one left. > Pictures available (end of sales pitch). > > Dave - K9FN > > On Wed, Oct 15, 2014 at 1:48 PM, Ken G Kopp wrote: > >> A sometimes forgotten source of foot switches is local music stores. >> >> 73 >> >> K0PP >> __ Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [K2] Output power not matching power setting and very unstable between transmissions
Don, Thank you for your recommendations. D9 is a 1N5711 and checks OK. A full reset made no difference. Setting CAL CUR to 3.5 reduces the frequency of the HI-CUR messages, however with the power control maxed it will still show up sometimes. Note that when the HI-CUR occurs it is only for a second, after which the power drops down to some random stable level. Base of Q7 and Q8 are between .60 and .64 volts While adjusting the power control with the radio in receive the power shown on the display changes very smoothly as it should. However, if the power control is adjusted while transmitting the power shown on the LCD display and the LED bar graph jumps all over the place. The bar graph does show that the power is increasing and decreasing overall as it should, what I mean by that is the bar graph shows 4-5 bars of “noise” while adjusting the power in transmit, but the overall direction of the “noise” goes up or down in the correct direction if you were to average the “noise”. Another test I made, however I’m not sure it is valid, was to control VPWR manually by lifting R22 where is meets C45 and inserting a control voltage on the lifted end of R22. In this mode the power is stable and varies smoothly as the external control voltage is varied. The power output is also stable from tune cycle to tune cycle in this test. I question the validity of this test because VPWR and VALC are already setup and stable prior to transmitting, unlike they normally would. Steve - KY7K k...@arrl.net Get OUT and play radio! On Oct 5, 2014, at 6:35 AM, Don Wilhelm wrote: > Steve, > > If "hooked up backwards" means that the DC power was connected with > reverse polarity, that will normally cause no harm to the K2 because > there is a series reverse voltage protection diode in the input power > line. The burned trace on the mic jack pin 5 suggests that something > different happened to it. > > Try replacing D9 with a 1N5711 diode and see what happens. The power > output into a good dummy load will normally be within 0.2 watts of the > set power if all is working right. You older K2 has a 1N34 diode at D9 > and it is not as accurate over the full frequency range as the 1N5711. > > If you have not done so already, record the menu settings, especially > the filter settings and do a Master Reset (hold the 4, 5, and 6 buttons > in while powering the K2 on). Then run CAL PLL and restore the menu > settings. The fact that the problem goes away if you swap control > boards suggests that there may be some problem with the EEPROM contents, > and a Master Reset should 'clean it out'. > > Set CAL CUR to 3.50 instead of 2.50 and see if the HiCur messages go > away. If they continue, you may have to replace the PA transistors. > Another thing to check is the DC voltage at the base of Q7 and Q8 during > a TUNE - it should be in the range of 0.60 to 0.64 volts. If not, > replace Q11 and Q13. > > 73, > Don W3FPR > > On 10/5/2014 1:36 AM, KY7K wrote: >> I forgot to mention that all testing is into a known good DL1 dummy load >> that I’m also using for my external power readings. >> >> Any wise insights are most welcome! >> >> Steve - KY7K >> k...@arrl.net >> Get OUT and play radio! >> >> On Oct 4, 2014, at 10:28 PM, KY7K wrote: >> >>> I recently purchased a used K2 (Rev A) from a club that was not working >>> because it had been “hooked up backward”. That is the best anyone can >>> remember as to what happened to the radio ~7 years ago… >>> >>> Currently, the power output as displayed on the radio and on an external >>> power meter is very unstable and does not match the power setting desired. >>> This is not just a little off, I can select 1W on the radio and then hit >>> the tune button 5 times and might get .4W, 6.7W, HI-CUR, 9.0W, 1.2W. >>> This is the QRP K2 with SSB, NB, KIO2 and DSP options. The problem occurs >>> with or without the option boards installed. >>> >>> Background: >>> When I first tested it, it would power on but the only function that was >>> operational was the power control. Every other knob and button was >>> non-functioning as if the cpu was hung up. The radio was not transmitting >>> in this state. >>> I had a old CPU (U6) from my other K2 that I installed as a test and that >>> seemed to fix the problem, at least in receive. I, unfortunately, did not >>> test it in transmit. >>> I ordered a FWK2MCIO kit to get a new cpu and also ordered all the mod kits >>> for the Rev A to Rev B upgrade, once they came in I installed everything >>> and while performing the the calibrations after the upgra
Re: [Elecraft] [K2] Output power not matching power setting and very unstable between transmissions
I forgot to mention that all testing is into a known good DL1 dummy load that I’m also using for my external power readings. Any wise insights are most welcome! Steve - KY7K k...@arrl.net Get OUT and play radio! On Oct 4, 2014, at 10:28 PM, KY7K wrote: > I recently purchased a used K2 (Rev A) from a club that was not working > because it had been “hooked up backward”. That is the best anyone can > remember as to what happened to the radio ~7 years ago… > > Currently, the power output as displayed on the radio and on an external > power meter is very unstable and does not match the power setting desired. > This is not just a little off, I can select 1W on the radio and then hit the > tune button 5 times and might get .4W, 6.7W, HI-CUR, 9.0W, 1.2W. > This is the QRP K2 with SSB, NB, KIO2 and DSP options. The problem occurs > with or without the option boards installed. > > Background: > When I first tested it, it would power on but the only function that was > operational was the power control. Every other knob and button was > non-functioning as if the cpu was hung up. The radio was not transmitting in > this state. > I had a old CPU (U6) from my other K2 that I installed as a test and that > seemed to fix the problem, at least in receive. I, unfortunately, did not > test it in transmit. > I ordered a FWK2MCIO kit to get a new cpu and also ordered all the mod kits > for the Rev A to Rev B upgrade, once they came in I installed everything and > while performing the the calibrations after the upgrade discovered that the > transmit power was very unstable between transmissions. > Other than the bad U6, the only other issue I found was that the PCB trace > from pin 5 of the Mic connector on the front panel board was basically > missing, from getting shorted to +12V I assume, it disintegrated when > touched... > > I’ve narrowed the issue down to the control board, since if I swap the > control board from my working K2 into the bad radio the power issue > disappears. > I’ve checked VRFDET, VALC, and VPWR on the control board and they are all OK > best I can tell, and I’m now at a loss where to look next. > Note: the power level is stable once it settles on some random output power. > The power level is random from one transmission to the next. > > The following links are images showing a tune cycle. > The first image shows the full scan with the radio set to ~1W and actually > putting out ~.4W. The second image is zoomed in on the start of the cycle. > https://www.dropbox.com/s/i64sw2ue2405roe/k2_0_5w_full.png?dl=0 > https://www.dropbox.com/s/qe297am756igbd4/k2_0_5w_zoom.png?dl=0 > > This is with the power set to ~7W and the radio indicating hi-cur, before > settling down to ~6.4W > https://www.dropbox.com/s/tqxzi3yk13gye4g/k2_hicur_full.png?dl=0 > https://www.dropbox.com/s/6qz10478zt66tjd/k2_hicur_zoom.png?dl=0 > > > > Steve - KY7K > k...@arrl.net > Get OUT and play radio! > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k...@cox.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] [K2] Output power not matching power setting and very unstable between transmissions
I recently purchased a used K2 (Rev A) from a club that was not working because it had been “hooked up backward”. That is the best anyone can remember as to what happened to the radio ~7 years ago… Currently, the power output as displayed on the radio and on an external power meter is very unstable and does not match the power setting desired. This is not just a little off, I can select 1W on the radio and then hit the tune button 5 times and might get .4W, 6.7W, HI-CUR, 9.0W, 1.2W. This is the QRP K2 with SSB, NB, KIO2 and DSP options. The problem occurs with or without the option boards installed. Background: When I first tested it, it would power on but the only function that was operational was the power control. Every other knob and button was non-functioning as if the cpu was hung up. The radio was not transmitting in this state. I had a old CPU (U6) from my other K2 that I installed as a test and that seemed to fix the problem, at least in receive. I, unfortunately, did not test it in transmit. I ordered a FWK2MCIO kit to get a new cpu and also ordered all the mod kits for the Rev A to Rev B upgrade, once they came in I installed everything and while performing the the calibrations after the upgrade discovered that the transmit power was very unstable between transmissions. Other than the bad U6, the only other issue I found was that the PCB trace from pin 5 of the Mic connector on the front panel board was basically missing, from getting shorted to +12V I assume, it disintegrated when touched... I’ve narrowed the issue down to the control board, since if I swap the control board from my working K2 into the bad radio the power issue disappears. I’ve checked VRFDET, VALC, and VPWR on the control board and they are all OK best I can tell, and I’m now at a loss where to look next. Note: the power level is stable once it settles on some random output power. The power level is random from one transmission to the next. The following links are images showing a tune cycle. The first image shows the full scan with the radio set to ~1W and actually putting out ~.4W. The second image is zoomed in on the start of the cycle. https://www.dropbox.com/s/i64sw2ue2405roe/k2_0_5w_full.png?dl=0 https://www.dropbox.com/s/qe297am756igbd4/k2_0_5w_zoom.png?dl=0 This is with the power set to ~7W and the radio indicating hi-cur, before settling down to ~6.4W https://www.dropbox.com/s/tqxzi3yk13gye4g/k2_hicur_full.png?dl=0 https://www.dropbox.com/s/6qz10478zt66tjd/k2_hicur_zoom.png?dl=0 Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Problems with K3 firmware update
I did the same. Check thrift stores for a RS-232 switch if you don’t already have one. I picked mine for 25 cents at the local thrift store. scl > > On 2014-08-14 9:00 PM, Jim N7US wrote: >> I connected an A/B switchbox to switch the radio between the MKII and a >> serial port on the computer (or an Edgeport US/serial box). It has been >> easy to switch the K3/P3 to the serial port for firmware updates. >> >> 73, Jim N7US >> >> >> >> -Original Message- >> >> Every microHAM Users Manual includes a specific warning *NOT* to upload >> *any* transceiver firmware via the microHAM device. The microHAM device >> constantly polls the transceiver for frequency and mode. Those polls are >> not compatible with firmware uploads. >> >> 73, >> >> ... Joe, W4TV >> >> >> On 2014-08-14 7:30 PM, Don Wilhelm wrote: >>> Kurt, >>> >>> Both Microham and Elecraft warn that one should not attempt firmware >>> downloads through the MicroHam device. Other K3Utility functions work >>> fine through the Microham device. >>> >>> If you have a real serial port on the computer, that is the preferred >>> connection, otherwise a good USB to serial adapter is the best answer. >>> The preferred adapter is one using an FTDI chip. Others may work (and >>> I can also recommend EdgePort). >>> >>> BTW - there are counterfeit FTDI and Prolific USB to serial adapters >>> on the market. Both Prolific and FTDI have created new drivers for >>> Windows >>> 7 and above that detect those counterfeits and render them unusable - >>> so steer clear of bargain priced adapters whose instructions tell you >>> to turn off Windows updates and run their 'special' drivers. >>> >>> The Elecraft KUSB cable uses an authentic FTDI chip. I have also had >>> success with a Keyspan adapter that was supplied for testing by a >> customer. >>> >>> 73, >>> Don W3FPR >>> >>> On 8/14/2014 7:02 PM, Kurt Wiksten wrote: >>>> Thanks to everybody for your advice. >>>> But my problem still not solved, because I am communicating with the >>>> K3 via my Microkeyer2. >>>> Reading the K3 Utility Helpfiles shows that it might be a problem >>>> that my USB to serial connection is via my Microkeyer2 and the >>>> recommendation is to change the cabling so that the PC is connected >>>> directly to the K3 and that cable does not fit the K3 RS232 port. >>>> I suppose I will have to order the KUSB-cable from Elecraft. >> >> >> >> >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to li...@subich.com >> > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k...@cox.net Steve - KY7K k...@arrl.net Get OUT and play radio! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] KX3 single lever key
Add my begging and pleading for Ultimatic mode in the KX3 and K3 if at all possible!! On Jul 16, 2012, at 11:36 AM, Don Wilhelm wrote: > I have similar difficulty John, those *#%! alternating dits and dahs are > just not for me. > I can use a dual lever paddle if the keying is Ultimatic - no > alternating, and the last paddle closed gets priority. > > So Wayne, if enough of us beg, can you add Ultimatic keying? Especially > desired for the KX3. > > 73, > Don W3FPR > On 7/16/2012 2:22 PM, John Buck wrote: Steve - KY7K k...@cox.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] KX3 Ultimatic mode?
Does the KX3 include Ultimatic keying mode? I was thinking of adding the KXPD3 key to my order but don't want to do it if I will need an external keyer to get Ultimatic. Thanks in advance. Steve - KY7K __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
