mouse problems on Compaq nc4000 / 5.2-BETA
Hello, I've tried to install 5.2-BETA (with ACPI) on my Compaq nc4000 notebook and in /dev I can't find psm(4) entry - it doesn't exist. I've tried to boot my notebook without ACPI - mouse works well, I can "use" /dev/psm ... I've tried to dump/compile ACPI DSDT table, but I found only one warning: Compiling "acpi.dsl" acpi.dsl 3898: Name (_WDG, Buffer (0x50) Warning 2033 - ^ Unknown reserved name (_WDG) ASL Input: acpi.dsl - 5180 lines, 163519 bytes, 2800 keywords AML Output: DSDT.aml - 20599 bytes 712 named objects 2088 executable opcodes Compilation complete. 0 Errors, 1 Warnings, 0 Remarks, 679 Optimizations Is it possible to make my build-in mouse work with ACPI :) ? Thank you. vd ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Fatal trap 12: ... while installing emulators/linux_base
Hello, I've tried to install emulators/linux_base on my FreeBSD 5.1-CURRENT (todays world) and got the following: Fatal trap 12: page fault while in kernel mode fault virtual address = 0x3 fault code = supervisor read, page not present instuction pointer = 0x8:0xc04c1190 stack pointer = 0x10:0xe907e6d4 frame pointer = 0x10:0xe907e6d8 code segment= base 0x0, limit 0xf, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags= resume, IOPL = 0 current process = 1648 (rpm) kernel: type 12 trap, code=0 I've tried to install with GENERIC and my custom kernel - same problem ... vd ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Re: Entropy harvesting: interrupts ethernet point_to_point
On Thu, 4 Sep 2003, Putinas wrote: > Hi all, > on the recent src with custom compiled kernel ( generic minus some stuff > what I don't need ) with firewall compiled in kernel , system infinitely > hangs on boot unless I press ctrl-c at this point: > Entropy harvesting: interrupts ethernet point_to_point > Same things happens on two different computers with nearly similar custom > kernel configuration > Could you tell me, what's causing the problem ? > * If needed I can submit my kernel configuration * Strange, but the same problem I had on my Compaq Evo N610C with ACPI turned on. Without ACPI all works well ... > > Regards, > Putinas Piliponis > vd ___ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-current To unsubscribe, send any mail to "[EMAIL PROTECTED]"
RE: Mylex support under 5.0-R
> Hi, > > Is it just me or is the Mylex driver broken under FreeBSD 5.0-Release? > I couldn't dig up anything related in archives. I'm aware of > bootup issues > using Mylex cards, but I already have it installed on IDE and > trying to > work with a drive connected to a mylex controller locks up the system. > Scott Long is working on this problem. > Thank you, > Simon vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
iir problems on -CURRENT
Hello *, Few minutes ago I tried to install FreeBSD 5.0-CURRENT (kernel 2002.12.19) with Intel SRCU31A RAID Controller (firmware 2.34.00-R030) . After unsuccessful try to do it via 'sysinstall', I tried to install FreeBSD to IDE drive and access Intel RAID Controller. I was unsuccessful too. I got following: iir0: mem 0xfc8f-0xfc8f3fff irq 18 at device 9.0 on pci3 ... GEOM: new disk ad0 ar: FreeBSD check1 failed ad0: ATA-2 disk at ata0-master ad0: 2014MB (4124736 sectors), 4092 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA33 ad0: piomode=4 dmamode=2 udmamode=2 cblid=0 Waiting 15 seconds for SCSI devices to settle GEOM: Configure ad0s1, start 32256 length 2111832576 end 2111864831 GEOM: Add ad0s1 hot[0] start 512 length 276 end 787 GEOM: Configure ad0s1a, start 134217728 length 1977614848 end 2111832575 GEOM: Configure ad0s1b, start 0 length 134217728 end 134217727 GEOM: Configure ad0s1c, start 0 length 2111832576 end 2111832575 (probe6:iir0:0:6:0): error 22 (probe6:iir0:0:6:0): Unretryable Error ... Any ideas ? vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
FreeBSD 5.0-DP2 & Mylex AcceleRAID 170
Hello, (again & again) I'm trying to install 5.0-DP2 on my little server and at this time: DEBUG: trying to piece 82 of 249: /base/base.dd (da0:mly0:1:0:0): Request Requered (da0:mly0:1:0:0): Retrying Command And sysinstall hangs ... vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
RE: SCSI & 'iir' problems on -CURRENT
On Fri, 15 Nov 2002, Patrick Fish wrote: > When you upgrade to 5.0, you need to do the following things from > console: > > cd /usr/src/sys/boot/ && make && make install > > > This is because the kernel location was changed, so you need to make > boot manually. > > I also suggest you compile pam.d manually also. > I tried to do binary upgrade (4.7->5.0) because plain 5.0 installation is impossible - same problem. > pf > vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
SCSI & 'iir' problems on -CURRENT
Hello, Few minutes ago I tried to upgrade 4.7 -> 5.0 (2002.11.15) and after reboot I got problem: Waiting 15 seconds for SCSI device to settle Mounting root from ufs:/dev/da0s1a sethostbyname failed ffs_mountroot: can't find rootvp Root mount failed: 6 mountroot> ? List of GEOM disk devices: geom.ctl 4.7 works with Intel RAID Controller SRCU32, but with 5.0 I have this problem ... vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
5.0 & Mylex AcceleRaid170
Hello, I'm trying to install 5.0 (2002.11.12 snapshot) on: Intel SE7500WV2 server board 2x Xeon 2 Ghz 2 Gb. RAM 6x 73 Gb. SCSI disks Mylex AcceleRaid 170 I made: UFS: / - 8 gb swap - 8 gb /usr - 16 gb /var - 16 gb UFS2: /data - 300 gb And ... sysinstall simply hangs on 69% on files extract into '/'. I tried: - install from CD-ROM & FTP - all snapshots from 2002.11.03 till 2002.11.12 - with and without softupdates - RAID firmware upgrade/downgrade P.S. Linux (fuck) works well on this hardware :( vd To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
