On 3/2/2022 9:38 PM, Dr. William J. Schmidt wrote:
I have a KPA500 that faults on low (60 VDC) voltage.
Hi Bill,
It MIGHT be faulting because the HV is too low. It's an un-regulated
supply, so if line voltage is low, HV will be low. There's a jumper to
re-tap the power transformer, accessibl
I have a KPA500 that faults on low (60 VDC) voltage. After measuring the
power supply voltage at the PA module is perfectly fine. The voltage read
by the processor on the front panel via pin 10 of P1 is lower than it should
be and hence the fault condition. I suspect there is a voltage divider o
Hi Peder,
I encourage you to try QRP, especially with the high bands as hot as they've
been in a long time. And don't stop at 5 W! If a band is open you can make
contacts with 1 W, or even 0.1 W. For example, if you hear a station at S9 and
they're using 100 W, you'll be roughly 30 dB down at h
I have been thinking of playing around with QRP and wonder how to do 5
watts on the K3s without needing to recalibrate the gain each time. How do
people do 4 watts QRP with a K3s??
--
Peder Kittelson, W7RPK
__
Elecraft mailing list
Home
No, I haven't. ...
A friend changed my settings to display Morse to text and in trying to shut
off that feature I sort of have CWT blinking and a lot of stuff I don't
understand.
Thank you,
Jim W1FMR
On Wed, Mar 2, 2022, 8:51 PM SGS 126 wrote:
> Have you tried reloading the firmware?
>
> On W
That does not affect the settings. Those are all saved in the configuration.
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On Mar 2, 2022, at 5:50 PM, SGS 126 wrote:
>
> Have you tried reloading the firmware?
>
> On Wed, Mar 2, 2022 at 7:26 PM jimith...@gmail
Hopefully you saved the configuration using the KX2 Utility. If so, just reload
it.
In the manual, there is a table containing the menu descriptions and their
default options. Easy to go through and a good place to learn what they do.
EEINIT is described on page 56 of the manual. Basically th
Have you tried reloading the firmware?
On Wed, Mar 2, 2022 at 7:26 PM jimith...@gmail.com
wrote:
> I messed up settings trying to learn the menus . How do I get back, or to
> factory settings ?
> 72,
>
> Jim W1FMR
>
> Sent from Yahoo Mail on Android
> ___
I messed up settings trying to learn the menus . How do I get back, or to
factory settings ?
72,
Jim W1FMR
Sent from Yahoo Mail on Android
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mai
Thanks Ed! Don’t know how this chain got so scrambled. I’ll run it be
Elecraft too!
73, David, NS4V
David R. Hourdequin, PE
Specialty Heavy Timber Engineer
Hayesville, NC 28904
828-421-6216
> On Mar 2, 2022, at 02:03, Ed Cole wrote:
>
> Tried what you suggested Gary. No joy. The upper l
Firstly, Log4OM is a logging program, in this case version 2 or "next
generation".
Omnirig version 1.20, with K4 ini file loaded. Log4OM version 2.19, K4
firmware version R28.
My Omnirig settings are:
Rig type: Elecraft K4
Port: COM 16 (where my K4 USB appears on my Windows 10 PC)
Baud rate: 3840
11 matches
Mail list logo