Thanks, I was counting across, not up and down on the connector.
Thanks, for clarifying the pin configuration, which is not shown on the SM-120
section.
73's, Jim Kh6jkg.
-Original Message-
From: Eric Lemmon
To: Repeater-Builder@yahoogroups.com
Sent: Sun, Jun 13, 2010 9:
+ PL., pin 9 PTT, pin 11 Rx
audio , and
pin 3 Tx audio.
I noticed that the information on the SM-120 web page stated, in the front, the
RJ-45 pin 4 is at ground.
Could someone explain, or correct the Accessory connection.
Thanks,73's, JimKh6jkg.
rom Astron, where is the best place to mount the
diode/heat sinks?
On the power supply or on a rack panel, with good wires from the terminals to
the diode terminals.
Thank you for your comments.
73's, Jim Kh6jkg.
-Original Message-
From: Eric Lemmon
To: Repeater-Builder@yahoo
blem is constant transmit.
In my Vhf & Uhf book, there is a section for a Stn ctrl module., TLN5970A.
I await reply(s), thanks.
73's, JimKh6jkg.
-Original Message-
From: n3ssl
To: Repeater-Builder@yahoogroups.com
Sent: Sun, Apr 18, 2010 3:19 pm
Subject: [Repeater-B
What software & Rib interface is used on a Motorola SM-120?
Were can I locate the information on programming Motorola SM-120?
Thanks for your time.
73's, Jim Kh6jkg.
Thanks for your section in the Motorola Micor, Modification of the older
Station Control Module TLN4635B,
By Kevin Custer W3KKC.
Any chance there is a schematic for the Station Control Module TLN4635B ?
Thanks for all the information on all the repeaters.
73's, JimKh6jkg.
=
I was hoping the Optima technical folks, would state the best charger for
two Optima batteries in parallel is on the high price side . . . and the next
lower price unit is . . .
I await your reply. I am also interested in the best solar charger & controls.
73's, JimKh6jkg.
I have a RM-50. It has a 1/4" stud, by 1 1/4".
What is the BB option on your Astron?
I await your reply.
73's, JimKh6jkg.
-Original Message-
From: Mike Besemer (WM4B)
To: Repeater-Builder@yahoogroups.com; amateur-repa...@yahoogroups.com
Sent: Fri, Nov 20, 2009
Does anyone have a source for these capacitors,
Which are used in Motorola Micor power supplies?
TPN1106A? C1006-C1009? 2000 mfd, 100V @10%
C1012, C1013? 17,500 mfd 20V @10%
TPN1110A???C1? 6 mfd @ 660v
C2-9 17,500 mfd 20v @ 10%
TPN1151A? C1-2? 8000 mfd 35v @ 10%
73's,??? Jim?Kh6jkg.
CR1, CR2, CR3, CR4.
Any inputs are welcome.
73's, Jim Kh6jkg.
- Original Message-
From: kh6...@netscape.net
To: Repeater-Builder@yahoogroups.com
Sent: Tue, 24 Feb 2009 10:10 am
Subject: [Repeater-Builder] Motorola Micor Power Supply - TPN1110B
Thanks Eric for the correction on the model
shorted.
Thanks, 73’s, Jim Kh6jkg.
Jim,
It took me a while to figure out what you have. TLN5123B is not the model
of the power supply; it is the part number of the
Chassis and Hardware Kit in a TPN1110B Power Supply.
If your power supply blows the 10 ampere fuse F1 with no load connected to
are CR1, CR2, CR3, CR4.
Although, I have not seen many power supplies with C1 across one of the
secondary, like Motorola P.S.
It would be best to replace all four.
Please send me your input, on?the likely faulty component(s) to check.
Thanks for your emails.
73's,?? Jim??? Kh6jkg.
ng with my old
Windows 3.1 software.
This will mean taking this desk top to the repeater site, to program the
repeater
controller.
I have a USB to Db-9, RS-232c adapter w/ a cd software. If I could get a
Windows AT program to work with XP.
I await your solutions.
73's & Thanks.
Jim???
LN4635B
Line driver - TLN4668B
Sq. gate - TLN4662A
Time out timer - TLN4636A
Any input which will make this simpler ?
Thanks for your input.
73's,
Jim Kh6jkg.
their area.
Thanks for the information on this topic.
73's,
Jim Kh6jkg.
More new features than ever. Check out the new AIM(R) Mail ! -
http://webmail.aim.com
circuit should also be used.
Does Xantrex or http://www.newmarpower.com/ have a cut-off & a over discharge
circuit?
My batteries are awaiting for the properly controlled charger, with as much
details.
Thanks & 73’s,
Jim
gh out all this
looking, I have yet to find a list.
Thanks, for the Micor PL Encoder modifications, which I will add to our Micor.
73's,
Jim??? Kh6jkg.
More new features than ever. Check out the
After searching the repeater-builder.com for Micor power supplies, then my
emails to the beginning of 2006.
I came across this which might be what I am looking for. Although, it is not in
the repeater-builder pages.
Any information would be appreciated.
Tnx & 73's,
Ji
r output to ERP? I guess, power
out(watts) - (1.5db)+(50' of LDF$-50)+9.2db=ERP output.
More details please.
Thanks.
73's,
Jim Kh6jkg.
__
Switch to Netscape Internet Service.
As low as $9.95 a month -- Sign up today at
;t have the model number handy.)
>>>
>>> Hope this helps,
>>> Neil - WA6KLA
What would be the next best charger, if one doesn’t have a Micor Power Supply
with the battery charger or our Micor Power Supplies don’t have the battery
charger ?
73’s,
JimKh6jkg.
_
"Randy" <[EMAIL PROTECTED]> wrote:
Hi Group I have a EV1 Transmitter with a PAV-1 Amplifier And a Hi Pro
R4V Reciever mounted in Housings. Can anyone help me with the
Interface to my controller. I have the following pins
Transmitter DB9 The Controller is a ICS Linker IIa
PIN 1 Audi
6 antennas use about 19.5" long radials.
Should the radials be straight, like the GP-6, or angled down some degree(s)?
What should the length of the radials be, for a UHF band antenna?
73's,
Jim Kh6jkg.
__
Switch to Netscape
Where can I locate a schmatic & wiring information on a
Motorola TRN-6413A Multi DPL Encoder board, which I have?
Which Motorola units used/use them?
Thanks,
73's,
Jim Kh6jkg.
__
Switch to Netscape Internet Service.
per equipment.
Where can I read more about sources of & how to interface microwave
communications equipment?
Are there many Ghz stations in the 48 states?
So, as you can see I have a basic idea of the parts used to get to 2.4 Ghz.
Although, I am intere
rge stock of GE parts, What are the part numbers that you are
>looking for.
>
>Todd
>Communications Service Company
>www.cencall.com
Kh6jkg>Here on Oahu, Hawaii, on 444.15R, we have a Mastr II.
How hard would it be to have a 444.50R, using another antenna?
What would be the u
d to have problems with flexing and lightning. When all
>but the bottom quarter wave section is disconnected due to flexing or
>lightning, there is no way to determine that you have an antenna problem
>from the ground.
>
>Just my thoughts. YMMV.
>
>73
>Glenn
>WB4UIV
&g
I am not an expert, but the first mic circuit would need an impedance
transformer, to keep the indivual mic circuits balanced or the audio level will
be less.
73's,
Jim Kh6jkg.
__
Switch to Netscape Internet Service.
As l
oper installation of
these antennas.
On the sites with unused parts of these dual-band antennas, should the
unused section of the antenna be terminated? With a short or 50 ohm
termination?
Aloha,
Jim Kh6jkg
http://www.qsl.net/earc/
When visiting, Hawaii, I hope to QSO on our sy
28 matches
Mail list logo
