then simply turning on your receiver would start the motor if the
throttle stick was forward.
So the correct sequence of starting an electric model is:1, switch on the
TX, 2, switch on the RX, 3, wiggle your sticks and OBSERVE, 4, hit the
arming switch, 5, advance the throttle.
Regards
Richard Knott
have a vario.
The upshot is: efficient coordinated turns are most important, and each
thermal / sailplane combination has its own ideal bank angle.
Regards
Richard Knott
Bell Equipment Co. South Africa
Wheeled Loader Marketing, Specials Aftersales Support
+27 (35) 907 9325 (ph) +27 (35) 907
a
trainer switch).
Regards
Richard Knott
- Original Message -
From: James Osborn [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Sunday, October 21, 2001 9:10 PM
Subject: [RCSE] Wanted: JR 8013 Buddy Box
I'm looking for a JR Tx that will work as a slave trainer Tx to my JR
8103. My
manual
Hi, you only need a new frequency module (and
receiver)if you are changing frequency bands, say from the 72MHz band to
35MHz. If you are changing from one 72MHz channel to another you only need to
change thecrystals.
Regards
Richard Knott
Bell Equipment Co. South AfricaWheeled Loader
Richard Knott
Bell Equipment Co. South Africa
Wheeled Loader Marketing, Specials Aftersales Support
+27 (35) 907 9325 (ph) +27 (35) 907 9611 (fax) +27 (0) 82 775 8061 (mobile)
- Original Message -
From: Dave Seay [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Sunday, July 29, 2001 9:42 PM
entire flight crew instead of just himself.
Regards
Richard Knott
Bell Equipment Co. South Africa
Wheeled Loader Marketing, Specials Aftersales Support
+27 (35) 907 9325 (ph) +27 (35) 907 9611 (fax) +27 (0) 82 775 8061 (mobile
conversion? What is the difference anyway?
Regards
Richard Knott
Bell Equipment Co. South Africa
Wheeled Loader Marketing, Specials Aftersales Support
+27 (35) 907 9325 (ph) +27 (35) 907 9611 (fax) +27 (0) 82 775 8061 (mobile
works on this principle: good connection between the electrodes and the
two plates so no arc there, poor connection
between the two plates being welded, gives a momentary arc and you have a weld.
Regards
Richard Knott
Bell Equipment Co. South Africa
Wheeled Loader Marketing, Specials Aftersales
,but it
must have been thousands of cycles.
Braided Kevlar line in several thicknesses is available from fresh-water fishing
stores. The whole point may be moot, depending on
how close to the load limit of the fibre it has been tensioned.
Regards
Richard Knott
Bell Equipment Co. South Africa
be a perfectionist though.
I'm sitting late at work designing a self-dumping wheeled loader bucket system,
rotating hydraulic cylinders and their lines of
action all over the place on CAD, so I guess this discussion is kinda pertinent to me
at the moment. :-)
Regards
Richard Knott
Bell Equipment Co
Hi All
I have a heavy-ish 3rd hand Algebra 3.2 (ailerons spoilers) with all-flying
tailplane which I am finding difficult to trim out.
Can anyone help me out with a recommended CG and decalage angle please? S3021 airfoil
I think.
Thanks
Richard Knott
BELL Equipment Co. South Africa
Wheeled
and
I said "go." He galloped excitedly several paces down the runway and then
enthusiastically flung the Algebra up at about 45 degrees
and about 20 degrees to the side...tipstall...inverted model 10 metres up...foot off
pedal...survived. Hi-start would have been
catastrophic.
My 2 cents w
hooked a 4-pound hammer... Scary, a high-speed hammer.
If your line is supplied in loose coils like the Shogun monofilament try to place the
coils over a large diameter piece of pipe
first.
Regards
Richard Knott
Tracy Coulson wrote:
I am trying to safely spool on new winch line. Can anybody
13 matches
Mail list logo