Re: [AFMUG] OT I have a big...

[Steve Jones]

I only like them green. On eggs in particular, i wanna let this bad boy
grow just to see how big it gets, but its also begging to be sliced on an
egg sandwich. Adulting is hard, decisions and stuff

On Jul 15, 2017 7:53 PM, "Jaime Solorza"  wrote:

Habanero ...what you going cook up with it? Or eat raw with a beer...

Jaime Solorza

On Jul 15, 2017 6:12 PM, "Steve Jones"  wrote:

> Habernero
>

Re: [AFMUG] OT I have a big...

[Jaime Solorza]

Habanero ...what you going cook up with it? Or eat raw with a beer...

Jaime Solorza

On Jul 15, 2017 6:12 PM, "Steve Jones"  wrote:

> Habernero
>

Re: [AFMUG] Drop Plow

[Jason McKemie]

I paid $12.9k for the 410sx - it has a bit higher hours than I'd like at
about 1500 and it is a 2005 model. They threw in the blade and a few
drilling rods. I've seen the ditch witch dealerships asking over $20k for
the same one with higher hours, and individuals/equipment resellers asking
the same amount I paid for mine for ones that were almost a decade older.
You can probably get one a bit cheaper, but I felt this was a decent deal
since it was from a dealer (not ditch witch though), and was owned by a big
telco (so it probably got regular maintenance). These things disappear
fast, if you find a good deal, snap it up as soon as you can. It seems like
LM42's can be had for a bit cheaper and are easier to find, service-wise
Ditch Witch was a better option for me since they're local.

On Friday, July 14, 2017, Adam Moffett  wrote:

> Can you share about how much it was and how well used it is in age or
> hours of operation?
>
>
> -- Original Message --
> From: "Jason McKemie"  >
> To: "af@afmug.com " <
> af@afmug.com >
> Sent: 7/14/2017 3:37:20 PM
> Subject: Re: [AFMUG] Drop Plow
>
> And yes, it goes on in place of the trencher.
>
> On Fri, Jul 14, 2017 at 12:11 PM, Jason McKemie <
> j.mcke...@veloxinetbroadband.com
> > wrote:
>
>> It's just unwieldy, I'm thinking I can use a shop crane to attach it
>> though.
>>
>>
>> On Friday, July 14, 2017, Adam Moffett > > wrote:
>>
>>> I've been eyeballing one of those for a long time.  I didn't know there
>>> was a hoe attachment..but I assume you have to take off the trencher or
>>> plow to put that on.
>>>
>>>
>>> -- Original Message --
>>> From: "Jason McKemie" 
>>> To: "af@afmug.com" 
>>> Sent: 7/13/2017 6:33:24 PM
>>> Subject: [AFMUG] Drop Plow
>>>
>>> First run with the new (to me) drop plow.
>>>
>>>
>

[AFMUG] Anyone Have Netonix Working With Multicast?

[Christopher Gray]

Does anyone here have Netonix switches working with Multicast / snooping?
If so, can you share how you did so?

Re: [AFMUG] powerinjector 10/100 pinout guide

[Forrest Christian (List Account)]

It's under warranty if you want to send it in.

Just send the serial (s) to the  cust...@packetflux.com address.

On Jul 14, 2017 9:02 PM, "Steve Jones"  wrote:

> Ended up being a bad board, was odd to cause the first site monitor was
> bad too, packetflux gear is never doa, ill get them on the bench and figure
> out what i broke to cause that
>
> On Jul 14, 2017 7:25 PM, "Forrest Christian (List Account)" <
> li...@packetflux.com> wrote:
>
>> That board must be a really early one.  I think there was about 100 of
>> each type which went out without jumper labeling for some reason I forget
>> now
>>
>> I sure don't see anything wrong with those jumpers.   Are you getting
>> power lights on the injector?  Do you have a base unit to look and verify
>> that the power is on on all of those ports.
>>
>> On Fri, Jul 14, 2017 at 5:02 PM, Steve Jones 
>> wrote:
>>
>>> Pwr 1 48
>>> Pwr 2 24
>>> 1 320
>>> 2 320
>>> 3 ubnt
>>> 4 fsk
>>> Is this correct? The fsk won't power. But I think I have a syncpipe
>>> parasitic up there
>>>
>>> On Jul 14, 2017 5:21 PM, "George Skorup" 
>>> wrote:
>>>
>>> It's printed on the board towards the left. Both the 10/100 and GigE
>>> versions have four jumpers per port. 10/100 jumpers are pins 4, 5, 7 & 8
>>> individually for the case of split-pair power like the 320 and 430. The
>>> GigE version is pairs (1&2/3&6/4&5/7&8) and will most definitely not do
>>> split-pair power without re-wiring the RJ45 at one end so that two wrongs
>>> make a right.
>>>
>>> Yes, I was about 1/2 a second away from screwing up once. Set the
>>> jumpers, put everything back together. Port 1 was set for 4-pair power and
>>> the 48VDC bus. A 450i AP was going there. Everything got upside down and I
>>> almost plugged a regular 450AP into port #1 until I realized my mistake
>>> before it was too late.
>>>
>>>
>>> On 7/14/2017 4:49 PM, Steve Jones wrote:
>>>
>>> packetflux poerinjector plus sync pinout for the jumpers. I have the
>>> document of PoE Injector Diagrams, but it doesn't seem right because by
>>> default these power cambium, but that not the jumper config. Pretty sure
>>> its the wrong document, and with mixing 24 and 48 with three different
>>> radio systems id prefer it be correct
>>>
>>> On Fri, Jul 14, 2017 at 4:44 PM, Colin Stanners 
>>> wrote:
>>>
 Here's my version 0.7 from 2012, I need to update it.


 On Fri, Jul 14, 2017 at 4:40 PM, Steve Jones >>> > wrote:

> Anybody have a current one, I don't think mine us, I'm using both
> inputs for 3 different kinds of radios and I am not even sure on which way
> to orient the board for the pins. I have 2 320s, a fsk 900, and a ubnt 24v
> radio
>


>>>
>>>
>>>
>>
>>
>> --
>> *Forrest Christian* *CEO**, PacketFlux Technologies, Inc.*
>> Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602
>> forre...@imach.com | http://www.packetflux.com
>> 
>>   
>>
>>