[amsat-bb] Re: Educate the Manufacturers
At 08:40 PM 12/16/2010, Andrew Glasbrenner wrote: On 12/17/2010 12:09 AM, Greg D. wrote: I believe this is the operative statement. I haven't tried it in a while (years), but I recall that my Alinco DR-610T mobile rig was not able to receive on 70cm while I was keyed up on 2m for a satellite contact. I remember this because it's frustrating when you can't hear what's going on. Haven't tried V/U satellite mobile since (and that was while parked in my driveway). The DR-610T is definitely capable of Cross-band Repeat, however. Greg KO6TH The 610 was definitely full duplex; see the second bullet at http://www.alinco.com/Products/DR-610T.shtml. I used a 605 extensively on satellite, and a friend has a 610 still. Just think about how a cross band repeater works, and you'll realize that any radio that does that must by design be capable of full duplex. 73, Drew KO4MA To repeat it has to receive while transmitting (that is duplex), but the DR-610T probably does not provide receive audio to the speaker when in cross-band mode. That means it is less useful for satellite work. It gets tricky to avoid audio feedback in that situation. Most repeaters do not have either mics or speakers, but certainly operate duplex. They often have connection for both for testing, however. 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 144-1.4kw, 432-100w*, 1296-testing*, 3400-winter? DUBUS Magazine USA Rep dubus...@hotmail.com == *temp not in service ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: AO7 Post Script
Thinking about this a little more, I can install a 2-foot stub tube on the existing satellite tower this winter and install the 2m yagi and half the 436CP42 for adequate Leo performance. All the wiring has been run so it makes sense to re-install something there. I have to lower the hinge-over tower to do a full restoration and I cannot get the truck onto the lawn in winter with over a foot of snow. I use the truck to raise and lower the tower. So I will first remove the existing antennas and equipment; and then remove the broken mast. Then Install antennas pre-mounted on the az-el rotator and, using a gin-pole, set them as a unit on a short stub mast affixed to the tower. I will not install the 1268 Tx and loop-yagi, and the dish. I will add the 8-dBi 2.4-GHz patch with preamp and install one drake (2.4G/123-MHz). That ought to provide a good variety of operating modes (V/U/S). The satellite equipment enclosure is currently installed on the tower with all cabling. It hasn't been used because I shorted the indicator electronics in the Yaesu B5400 control box so I was unable to rotate antennas. I will have the control unit to repair before I can use anything. 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 144-1.4kw, 432-100w*, 1296-testing*, 3400-winter? DUBUS Magazine USA Rep dubus...@hotmail.com == *temp not in service ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Yaesu FTM-350
Within a couple hours of each other, I have been told that the Yaesu FTM-350 can NOT receive on 440 while simultaneously keying up on 2M (1) - and that it WILL do that (2). I thought calling Yaesu tech support for my answer would be sufficient. They haven't disappointed me in the past. I apologize if what I posted in the '350 is incorrect. I went to the source for the info. Clint, K6LCS SOURCES: (1) Personal call to Yaesu tech support Thursday. (2) Dave, W5DMT ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] UO11
Hi Signal heard of UO11 today over GG54. http://www.youtube.com/watch?v=qU6mF79zTls 73 PY5LF LUCIANO FABRICIO CURITIBA-PR-BRAZIL GG54JM ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: LVB Tracker
Hi Harvey, Mine has held for almost a year now. It lost data after a power failure one time in the middle of tracking, but it seems to hold most of the time. 73, Joe KI4TZ H. Vordenbaum wrote: LVB Tracker with KR-5400A Controller. EEPROM does not hold calibration after Controller is turned off for a while. Do I have to go thru the calibration procedure every time it is turned on? Am I missing something here? 73, Harvey K5HV ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Sara Lily and Emma
Hello Signal of FAST 1 and FAST 2 over Brazil : http://www.youtube.com/watch?v=IU9j_42bB2I You can see the girls talking to each other after the third beacon transmission (7:30) . 73 PY5LF LUCIANO FABRICIO CURITIBA-PR-BRAZIL GG54JM http://www.qrz.com/db/py5lf http://www.qrz.com/db/py5lf http://www.falautomation.com.br/ www.falautomation.com.br ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Call For AMSAT Ideas Worth Stealing
Hello Everyone, In a recent ARRL Illinois Section Newsletter, Section Manager Tom Ciciora, KA9QPN listed several Ideas Worth Stealing which describes activities that have worked well for Illinois clubs and amateur radio operators. In keeping with the spirit, the idea of an Idea Worth Stealing is in itself worth stealing. Got that? This is a call for AMSAT Ideas Worth Stealing which we plan to include in the ANS bulletins when they pop up. Please send your Idea Worth Stealing to me: k9...@amsat.org -- 73 de JoAnne K9JKM k9...@amsat.org Editor, AMSAT News Service ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: LVB Tracker
I would say try to program another PIC and change it. I keep mine turned off for days and it does not loss the calibration. 73, Steve - Iw1RDZ - Messaggio originale - Da: Joe jbark...@truvista.net A: H. Vordenbaum tow...@stx.rr.com Cc: amsat-bb@amsat.org Inviato: Ven 17 dicembre 2010, 11:42:05 Oggetto: [amsat-bb] Re: LVB Tracker Hi Harvey, Mine has held for almost a year now. It lost data after a power failure one time in the middle of tracking, but it seems to hold most of the time. 73, Joe KI4TZ H. Vordenbaum wrote: LVB Tracker with KR-5400A Controller. EEPROM does not hold calibration after Controller is turned off for a while. Do I have to go thru the calibration procedure every time it is turned on? Am I missing something here? 73, Harvey K5HV ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Is there software to decode packet without a TNC?
Is there software to decode packet without a TNC? I would like to decode transmissions from the satellites but don't have a need to transmit and was wondering if such a program exists. Zack N8FNR ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
Zack, Yes, there is software available that can decode packet without a TNC, visit this site, I believe it will answer your questions. http://www.kc2rlm.info/soundcardpacket/ 73- Pete WB2OQQ www.massapequanyweather.com http://www.qrz.com/db/WB2OQQ? ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
I use AGWPE along with UISS. http://www.sv2agw.com/ham/agwpe.htm http://users.belgacom.net/hamradio/uiss.htm Dave - KB1PVH Sent from my VerizonWireless DROID On Dec 17, 2010 2:24 PM, vtnn...@comcast.net wrote: Is there software to decode packet without a TNC? I would like to decode transmissions from the satellites but don't have a need to transmit and was wondering if such a program exists. Zack N8FNR ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
Sure, UISS and AGWPE with a sound card interface like a Signalink USB or a homebrew interface. Works like a champ. http://www.kc2rlm.info/soundcardpacket/ Craig N6RSX -Original Message- From: amsat-bb-boun...@amsat.org [mailto:amsat-bb-boun...@amsat.org] On Behalf Of vtnn...@comcast.net Sent: Friday, December 17, 2010 11:10 AM To: AMSAT Subject: [amsat-bb] Is there software to decode packet without a TNC? Is there software to decode packet without a TNC? I would like to decode transmissions from the satellites but don't have a need to transmit and was wondering if such a program exists. Zack N8FNR ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb NOTICE: This communication may contain privileged or other confidential information. If you are not the intended recipient of this communication, or an employee or agent responsible for delivering this communication to the intended recipient, please advise the sender by reply email and immediately delete the message and any attachments without copying or disclosing the contents. Thank you. ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Thanks to all for the replies! RE: Is there software to decode packet without a TNC?
Thanks to all for the replies. It is appreciated 73 Zack ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
On 12/17/2010 2:10 PM, vtnn...@comcast.net wrote: Is there software to decode packet without a TNC? I would like to decode transmissions from the satellites but don't have a need to transmit and was wondering if such a program exists. Zack N8FNR ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb I use MixW to send and receive packet, and many other modes. http://mysite.verizon.net/jaffejim/ 73, Drew KO4MA ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Thanks to all for the replies! RE: Is there software to decode packet without a TNC?
On Fri, December 17, 2010 20:35, vtnn...@comcast.net wrote: Thanks to all for the replies. It is appreciated Also take a look at MixW 73 Zack 73 Jan - PE0SAT ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] M-Squared Eggbeater woes
From the ground, I can see that the fiberglass support rod for the loops on my 2-meter M2 Eggbeater has separated from the center housing, and the loops are now bobbing around in the wind. Before I even *think* about climbing up there to fix it or put something else in its place in the middle of a Chicago winter, can anyone provide any details on how the rod attaches to the housing? (photographs would be even better) It's been up there a while, and my memory of the construction has faded George, KA3HSW ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] MixW demo videos mp3 for getting started
Is there software to decode packet without a TNC? Hi Zack ! After you installed MixW, you can test it with a mp3 recording at my website: http://www.pa3guo.com/ooreos_26nov2010_pa3guo.mp3 This is a recent recording of 1200 baud packety from O/OREOS, one of the new satellites. MixW should decode and show them all on the screen. Simply replay the mp3 and see if MixW can decode it for you. Also I have 2 Youtube videos that demonstrate this on O/OREOS: http://www.youtube.com/watch?v=M4Ka-RVpEHU (screen recording of MixW) http://www.youtube.com/watch?v=Qh6lH5vqw-Y (shows also DK3WN software) And finally, this is how MixW works on ISS packet: http://www.youtube.com/watch?v=FSFVTN2KKog All these YouTube videos are best viewed (full screen) in HD quality. Do you let us know your results ? Success ! Henk, PA3GUO http://www.pa3guo.com -- Henk, PA3GUO ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] AO-27 website times wrong again
FYI: The AO-27 website schedule lister is behind the satellite's actual mode changes again, by about 23 minutes. Last time this happened, Mike Wyrick said it was due to the NTP client on the web server stopping. I have e-mailed him to let him know that there's a problem again. The Java schedule lister, however, is only behind by about 2 minutes at the present time. This is due to a cumulative error in the satellite clock. George, KA3HSW Java lister available at: http://sites.google.com/site/ao27satellitescheduler ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] ARISSat-1 and FOX PayPal widget fundraising
Hi all, We are just about to cross the $1000 mark on our PayPal fundraiser, and along with the $710 raised from the Facebook campaign, we are making a dent in recovering the funds spent on ARISSat-1 and those funds that will be spent on FOX. I want to thank those that donated, and those that took the time to add the widget to their webpages and QRZ profiles, and especially recognize two members who have excelled in creating exposure for our campaign. John Papay, K8YSE and Clint Bradford, K6LCS have pulled away from the pack in the number and amount of donations resulting from their copies of the widget, with $290 dollars raised between them. Gentlemen, thank you! I've talked with Martha, and beginning with the $1250 mark, we will be randomly picking a donor from every $250 increment to receive an item from the AMSAT store. We currently have two different hats, a nice luggage tag, or a desktop thermometer/clock set to choose from, all bearing the AMSAT name and logo. I hope to announce our first recipient soon! Thanks again, and if you'd like to donate to the campaign or share the widget to your own website, please visit www.amsat.org. The widget is on the front page below the ARISSat-1 news, and you can click on Give to donate, or add to site to receive the HTML code, or supporters to scroll through the statistics. I hope to soon see more familiar names scrolling across the widget soon, showing your support for AMSAT's next two satellites. 73, Drew KO4MA AMSAT-NA VP Operations PS Donations, memberships, and store purchases may also be made through the AMSAT store on the website, or by calling Martha at 1 888 322 6728. ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] 2204 AO-27 Pass - K7CWP????
I thought I copied K7CWP but I guess that was wrong. Anyone copy the correct call? Thanks and 73! John Belstner W9EN Valley Center, CA DM13le ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
Is there software to decode packet without a TNC? I've been recording passes and decoding .wav files after the fact with TrueTTY. No need for a rig/soundcard interface. It's a bit clumsy, but easy. My satellite ops are all portable and I don't have a notebook computer. 73, Scott N1AIA ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: 2204 AO-27 Pass - K7CWP????
If it was from CN94 it was most likely Loren K7CWQ Clear Skies Rick Tejera Editor SACnews, Public Outreach Coordinator Saguaro Astronomy Club Phoenix, Arizona www.saguaroastro.org saguaroas...@cox.net K7TEJ, AMSAT 38452 -Original Message- From: amsat-bb-boun...@amsat.org [mailto:amsat-bb-boun...@amsat.org] On Behalf Of John M. Belstner Sent: Friday, December 17, 2010 15:32 To: amsat-bb@amsat.org Subject: [amsat-bb] 2204 AO-27 Pass - K7CWP I thought I copied K7CWP but I guess that was wrong. Anyone copy the correct call? Thanks and 73! John Belstner W9EN Valley Center, CA DM13le ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
Is there a link? Clear Skies Rick Tejera Editor SACnews, Public Outreach Coordinator Saguaro Astronomy Club Phoenix, Arizona www.saguaroastro.org saguaroas...@cox.net K7TEJ, AMSAT 38452 -Original Message- From: amsat-bb-boun...@amsat.org [mailto:amsat-bb-boun...@amsat.org] On Behalf Of Scott Richardson Sent: Friday, December 17, 2010 17:00 To: vtnn...@comcast.net; AMSAT Subject: [amsat-bb] Re: Is there software to decode packet without a TNC? Is there software to decode packet without a TNC? I've been recording passes and decoding .wav files after the fact with TrueTTY. No need for a rig/soundcard interface. It's a bit clumsy, but easy. My satellite ops are all portable and I don't have a notebook computer. 73, Scott N1AIA ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: Is there software to decode packet without a TNC?
Scott I am curious how do you record ? I tried digital note takers once and they were not much chop Andrew Sent from my iPhone Andrew Rich On 18/12/2010, at 9:59, Scott Richardson sc...@aves-specta.com wrote: Is there software to decode packet without a TNC? I've been recording passes and decoding .wav files after the fact with TrueTTY. No need for a rig/soundcard interface. It's a bit clumsy, but easy. My satellite ops are all portable and I don't have a notebook computer. 73, Scott N1AIA ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: M-Squared Eggbeater woes
George, I re-read your email and realized you were asking how the *fiberglass rod* connects to the balun case. The manual shows the balun case/support rod as one item, so I don't know how the rod is secured. My guess is that it's a force-fit into the delrin ring at the top of the balun. I can send you a scan of the manual, or some pictures of my eggbeater if that would help. The loops are secured with Allen screws at their bottom. They take a 3/32 Allen wrench to tighten them (I just checked this on my Eggbeater). You might want to make sure there's no ice in the hex hole, or the wrench won't get a good bite. Let me know if you need a copy of the manual and I'll email it. Bill N5AB On Dec 17, 2010, at 2:16 PM, George Henry wrote: From the ground, I can see that the fiberglass support rod for the loops on my 2-meter M2 Eggbeater has separated from the center housing, and the loops are now bobbing around in the wind. Before I even *think* about climbing up there to fix it or put something else in its place in the middle of a Chicago winter, can anyone provide any details on how the rod attaches to the housing? (photographs would be even better) It's been up there a while, and my memory of the construction has faded George, KA3HSW ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: M-Squared Eggbeater woes
George, The loops are secured with Allen screws at their bottom. They take a 3/32 Allen wrench to tighten them (I just checked this on my Eggbeater). You might want to make sure there's no ice in the hex hole, or the wrench won't get a good bite. Let me know if you need a copy of the manual and I'll email it. Bill N5AB On Dec 17, 2010, at 2:16 PM, George Henry wrote: From the ground, I can see that the fiberglass support rod for the loops on my 2-meter M2 Eggbeater has separated from the center housing, and the loops are now bobbing around in the wind. Before I even *think* about climbing up there to fix it or put something else in its place in the middle of a Chicago winter, can anyone provide any details on how the rod attaches to the housing? (photographs would be even better) It's been up there a while, and my memory of the construction has faded George, KA3HSW ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] K0BAM road trip
I'll be in DM58 this weekend for the following passes if anyone needs this grid: SATURDAY 12/18 - DM58 DELTA COUNTY COLORADO AO-27 1903z AO-51 2303z SO-50 2237z SUNDAY 12/19 - DM58 DELTA COUNTY COLORADO AO-27 2100z AO-51 2224z SO-50 2126z ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] More On Akatsuki Venus Probe
http://mdn.mainichi.jp/mdnnews/news/20101218p2g00m0dm014000c.html http://www.yomiuri.co.jp/dy/national/T101217004031.htm 73s Bernhard VA6BMJ @ DO33FL ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
[amsat-bb] Re: More On Akatsuki Venus Probe
Quoting from the article: Since Akatsuki failed to maintain the correct attitude during reverse thrust for entry into orbit around Venus on Dec. 7 Most unfortunate for the failure of their space craft on Dec. 7th. Bob- W7LRD - Original Message - From: B J top_gun_can...@yahoo.com To: amsat-bb@amsat.org Sent: Friday, December 17, 2010 9:00:09 PM Subject: [amsat-bb] More On Akatsuki Venus Probe http://mdn.mainichi.jp/mdnnews/news/20101218p2g00m0dm014000c.html http://www.yomiuri.co.jp/dy/national/T101217004031.htm 73s Bernhard VA6BMJ @ DO33FL ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb ___ Sent via amsat...@amsat.org. Opinions expressed are those of the author. Not an AMSAT-NA member? Join now to support the amateur satellite program! Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb