[asterisk-users] zaptel issue
Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] zaptel issue
Interesting, the bottom of my previous email disappeared ... so here is again. Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further. I get past make clean, ./configure, then when I get to make install I get this error. #$ sudo make install make[1]: Entering directory `/var/ports/zaptel-1.4.11' make -C /lib/modules/2.6.18-53.1.19.el5/build ARCH=x86_64 SUBDIRS=/kernel HOTPLUG_FIRMWARE=yes KBUILD_OBJ_M=pciradio.o tor2.o torisa.o wcfxo.o wct1xxp.o wctdm.o wcte11xp.o wcusb.o zaptel.o ztd-eth.o ztd-loc.o ztdummy.o ztdynamic.o zttranscode.o wct4xxp/ wctc4xxp/ xpp/ wctdm24xxp/ wcte12xp/ modules make[2]: Entering directory `/usr/src/kernels/2.6.18-53.1.19.el5-x86_64' scripts/Makefile.build:17: /kernel/Makefile: No such file or directory make[3]: *** No rule to make target `/kernel/Makefile'. Stop. make[2]: *** [_module_/kernel] Error 2 make[2]: Leaving directory `/usr/src/kernels/2.6.18-53.1.19.el5-x86_64' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/var/ports/zaptel-1.4.11' make: *** [all] Error 2 -Original Message- From: Eve-Ellen Cole [mailto:[EMAIL PROTECTED] Sent: Tuesday, June 10, 2008 4:01 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: zaptel issue Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further. ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] zaptel issue
On Tue, Jun 10, 2008 at 04:00:44PM -0400, Eve-Ellen Cole wrote: Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further No need to uninstall. -- Tzafrir Cohen icq#16849755 jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] zaptel issue
On Tue, Jun 10, 2008 at 04:20:32PM -0400, Eve-Ellen Cole wrote: Interesting, the bottom of my previous email disappeared ... so here is again. Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further. I get past make clean, ./configure, then when I get to make install I get this error. #$ sudo make install make[1]: Entering directory `/var/ports/zaptel-1.4.11' make -C /lib/modules/2.6.18-53.1.19.el5/build ARCH=x86_64 SUBDIRS=/kernel HOTPLUG_FIRMWARE=yes KBUILD_OBJ_M=pciradio.o tor2.o torisa.o wcfxo.o wct1xxp.o wctdm.o wcte11xp.o wcusb.o zaptel.o ztd-eth.o ztd-loc.o ztdummy.o ztdynamic.o zttranscode.o wct4xxp/ wctc4xxp/ xpp/ wctdm24xxp/ wcte12xp/ modules make[2]: Entering directory `/usr/src/kernels/2.6.18-53.1.19.el5-x86_64' scripts/Makefile.build:17: /kernel/Makefile: No such file or directory make[3]: *** No rule to make target `/kernel/Makefile'. Stop. Described here, including workaround: http://bugs.digium.com/12750 Any idea when this one last worked? make[2]: *** [_module_/kernel] Error 2 make[2]: Leaving directory `/usr/src/kernels/2.6.18-53.1.19.el5-x86_64' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/var/ports/zaptel-1.4.11' make: *** [all] Error 2 -Original Message- From: Eve-Ellen Cole [mailto:[EMAIL PROTECTED] Sent: Tuesday, June 10, 2008 4:01 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: zaptel issue Yesterday, freshly out of Asterisk Bootcamp, I attempted to resume an Asterisk installation on a new server. Zaptel 1.4.10.1 had been installed, but I decided to uninstall, and install Zaptel 1.4.11 before I went further. ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- Tzafrir Cohen icq#16849755 jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Zaptel issue
I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. At some point during the install of second card, wcusb starts loading. I believe this is one of the TE410 Cards causing this as there is no usb enabled. Module Size Used byNot tainted audit 89880 2 (autoclean) usbserial 23420 0 (autoclean) (unused) lp 8964 0 (autoclean) parport36832 0 (autoclean) [lp] autofs415832 0 (autoclean) (unused) tg367368 1 wcusb 19552 0 (unused) usbcore77376 0 [usbserial wcusb] wct4xxp70752 0 (unused) zaptel179872 4 [wcusb wct4xxp] floppy 56656 0 (autoclean) sg 36236 0 (autoclean) (unused) microcode 5688 0 (autoclean) ext3 85736 2 jbd50668 2 [ext3] aic7xxx 160880 0 (unused) diskdumplib 4940 0 [aic7xxx] sd_mod 13968 0 (unused) scsi_mod 106664 3 [sg aic7xxx sd_mod] If I rmmod the usb stuff, it come back on next reboot... At reboot, zaptel is complaining that modules are busy and can't remove them. How can I stop asterisk from loading this ? Bart ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Zaptel issue
On Monday 05 September 2005 15:38, Asterisk wrote: I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. Good luck. The interrupt issues alone are enough to make me run for my happy place. How can I stop asterisk from loading this ? Don't put everything in one box. Split it in two, or even three. Honestly, servers aren't that expensive and you're just begging for a disaster with this all your eggs in one basket implementation. -A. ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Zaptel issue
On Mon, 5 Sep 2005, Asterisk wrote: How can I stop asterisk from loading this ? Asterisk isn't doing this. Asterisk doesn't load kernel modules. You need to look at and understand the boot scripts that are loading the modules and remove the load of wcusb. You aren't using [EMAIL PROTECTED] by any chance? If so, look in /etc/sysconfig and grep for wcusb and edit that file. Steve ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
On Wednesday 03 November 2004 08:05 am, James Botham wrote: just interested to know what the contents of you /dev/zap/ctl directory are. ctl is not a directory. Look here: crw-r--r-- 1 root root 196, 0 Oct 30 16:40 /dev/zap/ctl And no you cannot readily cat a dev. I've not had to create any device files for a long time so I've forgotten how you do it, but the c means its a character device. It's a device that is read one character at a time. The command should be mknod so a man mknod should give you the details. And I cannot imagine why it was not created for you. It seems plausable that it should have been created at least by the time you run the zaptel install script. You could also just reinstall the binaries. There's script on szmidt.org/asterisk/asterisk-update.sh that will create backups of your source code and download, compile, install the asterisk system, etc. Simply run it without any parameter and it will give you the syntax. Not that running the install by hand is very hard... but I get lazy and try to automate everything. Which can make things overly complex. So it may still have some bug in it. Though it seems to run just fine now. -- Steve Szmidt They that would give up essential liberty for temporary safety deserve neither liberty nor safety. Benjamin Franklin ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
I have the following error once I have installed asterisk on my new Fedora Core 2 test 3 box with a T100P, compiled fine no problems after using the info on voip-info.org but when i run ztcfg i get this error message: Notice: Configuration file is /etc/zaptel.conf line 143: Unable to open master device '/dev/zap/ctl' I had the same problem when I tried to install zaptel on FC2. I resolved it by commenting out the following lines: ifeq ($(DYNFS),) else @echo Dynamic filesystem detected -- not creating device nodes @echo If you are running udev, read README.udev endif from the zaptel Makefile (lines 233, 253-256 as of this morning's Makefile). Hope this helps, Patrick ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
Title: RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 I have done as below now I get a new error message when trying to make clean or make install it says Makefile:230: *** missing rule before commands. Stop. In the build I have these lines were slightly different the ifeq ($(DYNFS),) is on line 230. I take it you didn't comment out the lines below as these look like they are creating the device nodes. Any ideas Thanks James -Original Message- From: Patrick Conroy [mailto:[EMAIL PROTECTED]] Sent: 05 November 2004 12:04 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 I have the following error once I have installed asterisk on my new Fedora Core 2 test 3 box with a T100P, compiled fine no problems after using the info on voip-info.org but when i run ztcfg i get this error message: Notice: Configuration file is /etc/zaptel.conf line 143: Unable to open master device '/dev/zap/ctl' I had the same problem when I tried to install zaptel on FC2. I resolved it by commenting out the following lines: ifeq ($(DYNFS),) else @echo Dynamic filesystem detected -- not creating device nodes @echo If you are running udev, read README.udev endif from the zaptel Makefile (lines 233, 253-256 as of this morning's Makefile). Hope this helps, Patrick ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
Title: RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 Ignore my last comment its worked hadn't commented it correctly. Apologies James -Original Message-From: James Botham [mailto:[EMAIL PROTECTED]Sent: 05 November 2004 12:27To: 'Asterisk Users Mailing List - Non-Commercial Discussion'Subject: RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 I have done as below now I get a new error message when trying to make clean or make install it says Makefile:230: *** missing rule before commands. Stop. In the build I have these lines were slightly different the ifeq ($(DYNFS),) is on line 230. I take it you didn't comment out the lines below as these look like they are creating the device nodes. Any ideas Thanks James -Original Message- From: Patrick Conroy [mailto:[EMAIL PROTECTED]] Sent: 05 November 2004 12:04 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 I have the following error once I have installed asterisk on my new Fedora Core 2 test 3 box with a T100P, compiled fine no problems after using the info on voip-info.org but when i run ztcfg i get this error message: Notice: Configuration file is /etc/zaptel.conf line 143: Unable to open master device '/dev/zap/ctl' I had the same problem when I tried to install zaptel on FC2. I resolved it by commenting out the following lines: ifeq ($(DYNFS),) else @echo " Dynamic filesystem detected -- not creating device nodes" @echo " If you are running udev, read README.udev" endif from the zaptel Makefile (lines 233, 253-256 as of this morning's Makefile). Hope this helps, Patrick ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
Title: RE: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 Patrick, Thanks for this info its working fine now, I have added this info to the voip-info site for anybody else experiencing it. Thanks James -Original Message- From: Patrick Conroy [mailto:[EMAIL PROTECTED]] Sent: 05 November 2004 12:04 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3 I have the following error once I have installed asterisk on my new Fedora Core 2 test 3 box with a T100P, compiled fine no problems after using the info on voip-info.org but when i run ztcfg i get this error message: Notice: Configuration file is /etc/zaptel.conf line 143: Unable to open master device '/dev/zap/ctl' I had the same problem when I tried to install zaptel on FC2. I resolved it by commenting out the following lines: ifeq ($(DYNFS),) else @echo Dynamic filesystem detected -- not creating device nodes @echo If you are running udev, read README.udev endif from the zaptel Makefile (lines 233, 253-256 as of this morning's Makefile). Hope this helps, Patrick ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Zaptel Issue in Fedora Core 2 test 3
Hi, I have the following error once I have installed asterisk on my new Fedora Core 2 test 3 box with a T100P, compiled fine no problems after using the info on voip-info.org but when i run ztcfg i get this error message: Notice: Configuration file is /etc/zaptel.confline 143: Unable to open master device '/dev/zap/ctl' The cards appear to load fine when i modprobe them no errors appear but Asterisk cannot use them when I make a call to the line in question asterisk doesn't acknowledge them, the config I am using is off my old machine (identical version same hardware and card just new OS) no errors on its startup euitither it seems to accept the config fine. | suspect that the channel has possibly changed but without ZTCFG i don't know how to check, does anybody have any ideas on a) what this message means and B is there anyway to see the channel the device is using. Cheers James BothamClient SupportConsultantComputer Software Group plcwww.computersoftware.com- TALENT Sport Europe's first 'paper' Smart tickets for Reading FC London Irish RFC www.computersoftware.com/smartticket.pdfTALENT CRM Electrolux Outdoor Products improve customer service with ROI in 6 months! www.computersoftware.com/eop.pdf _ This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the system manager. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. ___ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
