Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
The web interface is a bit confusing at first. Here are some of the steps that I remember off hand. Change as little as possible, makes it easier to troubleshoot later. Get the latest code from your vendor (5.6 is what I run) Configure the proxy to register with Configuration - Protocol Config - Protocol Def - Proxy and Registration - Enable registration - Set the registration per endpoint Configure your call routing Configuration - Protocol Config - Routing Tables - IP to Trunk Group If you send a prefix for outgoing calls, you will need to configure that in the manipulation table too Configuration - Protocol Config - Manipulation tables - Dest number IP to Tel Configure authentication Configuration - Protocol Config - Endpoint settings - Authentication Now the part that took me a while to find... Configure the Channel to phone number mapping: Configuration - Protocol Config - Endpoint Number - EndPoint Phone Number Configure the Hunt group settings Configuration - Protocol Config - Hunt/IP Group - Hunt group settings Hope that helps. These are great devices, once you figure out how to get them configured... -Jonathan On Sat, Dec 26, 2009 at 11:39 PM, Joseph syscon...@gmail.com wrote: I have AudioCodes MP-2FXO/2FXS but have a problem registering it with Asterisk. Any links or pointers to configuration how it is done? -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
What what everybody says, it is a good hardware but configuration samples are not easy to find and going through 500page manual is not easy. What they are missing is short configuration guide with samples for specific software like asterisk. My software version is 5.40A I see early next week what is the latest available. On 12/27/09 07:56, Jonathan Thurman wrote: The web interface is a bit confusing at first. Here are some of the steps that I remember off hand. Change as little as possible, makes it easier to troubleshoot later. I did not change much and trying to register just one line first, but is not easy all I'm getting is: chan_sip.c:15593 handle_request_register: Registration from 'sip:3...@10.0.0.109' failed for '10.0.0.157' - Wrong password 369 is my extension, 10.0.0.109 is my Asterisk server, 10.0.0.157 is AudioCodes IP Get the latest code from your vendor (5.6 is what I run) Configure the proxy to register with Configuration - Protocol Config - Protocol Def - Proxy and Registration - Enable registration - Set the registration per endpoint So I have Use Default Proxy: Yes Proxy Set Table: == What did you enter here (I enter: 10.0.0.109 UDP; do I need to set: Enable Proxy Keep Alive?) Proxy Name: 10.0.0.109 The below two settings (what to put in there, setting from sip.conf: eg.: but which one? Registrar Name Registrar IP Address Under: Gateway Name (I entered asterisk IP) 10.0.0.109 Again below is: User Name Password Not sure what to put in above. Configure your call routing Configuration - Protocol Config - Routing Tables - IP to Trunk Group Is above sections for routing calls to asterisk? If you send a prefix for outgoing calls, you will need to configure that in the manipulation table too Configuration - Protocol Config - Manipulation tables - Dest number IP to Tel No, I don't use prefixes they are dropped by asterisk; so I configured single stage dialing under: Advanced Applications - FXO Settings - Dialing Mode Configure authentication Configuration - Protocol Config - Endpoint settings - Authentication Here I entered authentication from one of my sip.conf entry: [369] [369] ; outgoing/incoming call on fxs port type=friend host=dynamic context=internal secret=523 username=369 mailbox=369 ;dtmfmode=rfc2833 ;dtmfmode=inband disallow=all allow=ulaw allow=alaw canreinvite=yes nat=no callgroup=1 pickupgroup=1 Now the part that took me a while to find... Configure the Channel to phone number mapping: Configuration - Protocol Config - Endpoint Number - EndPoint Phone Number Configure the Hunt group settings Configuration - Protocol Config - Hunt/IP Group - Hunt group settings Hope that helps. These are great devices, once you figure out how to get them configured... -Jonathan I need to find out from the manual what these setting do. I was hoping to find some setting reference on Wiki but there are none :-/ it seems to me the device is not very popular among asterisk users, if it was somebody would create detailed configuration for asterisk. -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
The best document is the two page quick start guide that came in the box. You want 5.6, and 5.8 should be out soon if you are an early adopter. -Jonathan Sent from a mobile device. On Dec 27, 2009, at 9:02 AM, Joseph syscon...@gmail.com wrote: What what everybody says, it is a good hardware but configuration samples are not easy to find and going through 500page manual is not easy. What they are missing is short configuration guide with samples for specific software like asterisk. My software version is 5.40A I see early next week what is the latest available. On 12/27/09 07:56, Jonathan Thurman wrote: The web interface is a bit confusing at first. Here are some of the steps that I remember off hand. Change as little as possible, makes it easier to troubleshoot later. I did not change much and trying to register just one line first, but is not easy all I'm getting is: chan_sip.c:15593 handle_request_register: Registration from 'sip: 3...@10.0.0.109' failed for '10.0.0.157' - Wrong password 369 is my extension, 10.0.0.109 is my Asterisk server, 10.0.0.157 is AudioCodes IP Get the latest code from your vendor (5.6 is what I run) Configure the proxy to register with Configuration - Protocol Config - Protocol Def - Proxy and Registration - Enable registration - Set the registration per endpoint So I have Use Default Proxy: Yes Proxy Set Table: == What did you enter here (I enter: 10.0.0.109 UDP; do I need to set: Enable Proxy Keep Alive?) Proxy Name: 10.0.0.109 The below two settings (what to put in there, setting from sip.conf: eg.: but which one? Registrar Name Registrar IP Address Under: Gateway Name (I entered asterisk IP) 10.0.0.109 Again below is: User Name Password Not sure what to put in above. Configure your call routing Configuration - Protocol Config - Routing Tables - IP to Trunk Group Is above sections for routing calls to asterisk? If you send a prefix for outgoing calls, you will need to configure that in the manipulation table too Configuration - Protocol Config - Manipulation tables - Dest number IP to Tel No, I don't use prefixes they are dropped by asterisk; so I configured single stage dialing under: Advanced Applications - FXO Settings - Dialing Mode Configure authentication Configuration - Protocol Config - Endpoint settings - Authentication Here I entered authentication from one of my sip.conf entry: [369] [369] ; outgoing/incoming call on fxs port type=friend host=dynamic context=internal secret=523 username=369 mailbox=369 ;dtmfmode=rfc2833 ;dtmfmode=inband disallow=all allow=ulaw allow=alaw canreinvite=yes nat=no callgroup=1 pickupgroup=1 Now the part that took me a while to find... Configure the Channel to phone number mapping: Configuration - Protocol Config - Endpoint Number - EndPoint Phone Number Configure the Hunt group settings Configuration - Protocol Config - Hunt/IP Group - Hunt group settings Hope that helps. These are great devices, once you figure out how to get them configured... -Jonathan I need to find out from the manual what these setting do. I was hoping to find some setting reference on Wiki but there are none :-/ it seems to me the device is not very popular among asterisk users, if it was somebody would create detailed configuration for asterisk. -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
I've emailed my provider Scansouce Communication to provide me with the newer firmware version but for now I'm trying to setup so I can at least register it with asterisk. Can you email me your INI file, I'll compare it to mine. I'm trying to register both ports with FXO and FXS with Asterisk. -- Joseph On 12/27/09 09:58, Jonathan Thurman wrote: The best document is the two page quick start guide that came in the box. You want 5.6, and 5.8 should be out soon if you are an early adopter. -Jonathan ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
On 12/27/09 09:58, Jonathan Thurman wrote: The best document is the two page quick start guide that came in the box. You want 5.6, and 5.8 should be out soon if you are an early adopter. -Jonathan The two page quick start does not work. I've follow the instruction in there, it is simple and straight forward but does not work with asterisk. -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
On 12/27/09 12:10, Joseph wrote: On 12/27/09 09:58, Jonathan Thurman wrote: The best document is the two page quick start guide that came in the box. You want 5.6, and 5.8 should be out soon if you are an early adopter. -Jonathan The two page quick start does not work. I've follow the instruction in there, it is simple and straight forward but does not work with asterisk. I've found good instruction at: http://lists.digium.com/pipermail/asterisk-biz/2006-May/014626.html It seems simple and straight forward but I still get: Registration from 'sip:3...@10.0.0.157' failed for '10.0.0.157' - Wrong password Is this Audiocodes so complicated? -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
I was able to register only one FXO port by setting in: Protocol Definition - Proxy Registration: Proxy Name: 10.0.0.109 Registrar IP Address: 10.0.0.109 User Name: pstn-5665 Password: 147 But how do I register other FXO and tow FXS ports? When I trying to enter in: Endpoint Settings - Authentication: Port 2 FXS 369 523 Port 4 FXO pstn-5665 147 Once I remove the setting User Name: pstn-5665 Password: 147 from: Proxy Registration registration fails. Here is my part from sip.conf: [369] ; internal extension FXS type=friend host=dynamic context=internal secret=523 username=369 mailbox=369 disallow=all allow=ulaw allow=alaw canreinvite=yes nat=no callgroup=1 pickupgroup=1 [pstn-5665] ; FXO type=friend secret=147 username=pstn-5665 host=dynamic canreinvite=yes disallow=all allow=ulaw allow=alaw nat=no context=incoming callgroup=1 pickupgroup=1 -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[asterisk-users] Audiocodes MP-114 2FXO/2FXS help registering with Asterisk
I have AudioCodes MP-2FXO/2FXS but have a problem registering it with Asterisk. Any links or pointers to configuration how it is done? -- Joseph ___ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
