[OSL | CCIE_Voice] Subject: MVA Fast Busy

[lou.can...@siriuscom.com]

Josh,

Check this:

!
application
 service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
^^^
 !
!
dial-peer voice 5010 voip
 description MVA DID
 destination-pattern 5999
 voice-class codec 1
 session target ipv4:10.10.210.10
 incoming called-number .
 dtmf-relay h245-alphanumeric
 no vad
!
dial-peer voice 2 pots
 service ccm
^^
 incoming called-number 2123945999


cmm vs ccm  


Regards,

Lou



--

Message: 7
Date: Wed, 15 May 2013 23:48:40 -0400
From: Josh Petro 
To: "ccie_voice@onlinestudylist.com" 
Subject: [OSL | CCIE_Voice] MVA Fast Busy
Message-ID:

Content-Type: text/plain; charset="iso-8859-1"

Hi All,

I'm on Volume 1 section 5C which is asking for Mobile Vocie Access
configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2
is a fast busy after a few seconds of silence.

I know this has been talked about in the past on this forum, but for the
life of me I can't find it.

I've followed what was in the workbook exactly and I'm not getting
anywhere. Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing
else in the flash directory. Is there something that needs to be
'installed' on the router to allow it to see the vxml code on the CUCM?
I've never been asked to do Mobile Voice Access before, so this is a first.

The CUCM is configured with the Mobile Voice Access number of 5999 and the
gateway is configured for 4 digits inbound (plus I tested other inbound
calls and they still work fine).

The Services parameters are correct and MVA is enabled. The voice-class
codec has G711u and G729r8 and that's it. I'm thinking codec, but I'm not
sure why.

I can't figure out what I missed.

Many thanks!
Josh

The config and debug isdn q931 output is below if it helps. I didn't get
the chance to get the voip ccapi debugs, so please let me know if you need
them and I'll grab them tomorrow.

!
application
 service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
 !
!
dial-peer voice 5010 voip
 description MVA DID
 destination-pattern 5999
 voice-class codec 1
 session target ipv4:10.10.210.10
 incoming called-number .
 dtmf-relay h245-alphanumeric
 no vad
!
dial-peer voice 2 pots
 service ccm
 incoming called-number 2123945999
 no digit-strip
!
!
!
!
!
!
HQ-RTR(config-dial-peer)#
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8  callref =
0x00A1
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x4180, '2123942123'
Plan:ISDN, Type:Subscriber(local)
Called Party Number i = 0xA1, '2123945999'
Plan:ISDN, Type:National
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: Received SETUP  callref = 0x80A1
callID = 0x0020 switch = primary-ni interface = User
May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: Application ccm in
dial-peer 2 not found.  Handing callid 187 to the alternate app .

HQ-RTR(config-dial-peer)#
May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8
 callref = 0x80A1
Cause i = 0x80BF - Service/option not available, unspecified
HQ-RTR(config-dial-peer)#

This message (including any attachments) is intended only for
the use of the individual or entity to which it is addressed and
may contain information that is non-public, proprietary,
privileged, confidential, and exempt from disclosure under
applicable law or may constitute as attorney work product.
If you are not the intended recipient, you are hereby notified
that any use, dissemination, distribution, or copying of this
communication is strictly prohibited. If you have received this
communication in error, notify us immediately by telephone and
(i) destroy this message if a facsimile or (ii) delete this message
immediately if this is an electronic communication.

Thank you.
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] MVA Fast Busy

[GRASSMUGG Christoph]

Hi,

Your Problem is...

Dial-Peer
Service ccm

But under Application your Service is caller cmm

So no Service can be found...

-Christoph

Sent from a Smartphone.

Am 16.05.2013 um 06:00 schrieb "Josh Petro" 
mailto:josh.pe...@gmail.com>>:

Hi All,

I'm on Volume 1 section 5C which is asking for Mobile Vocie Access 
configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2 is 
a fast busy after a few seconds of silence.

I know this has been talked about in the past on this forum, but for the life 
of me I can't find it.

I've followed what was in the workbook exactly and I'm not getting anywhere. 
Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing else in the 
flash directory. Is there something that needs to be 'installed' on the router 
to allow it to see the vxml code on the CUCM? I've never been asked to do 
Mobile Voice Access before, so this is a first.

The CUCM is configured with the Mobile Voice Access number of 5999 and the 
gateway is configured for 4 digits inbound (plus I tested other inbound calls 
and they still work fine).

The Services parameters are correct and MVA is enabled. The voice-class codec 
has G711u and G729r8 and that's it. I'm thinking codec, but I'm not sure why.

I can't figure out what I missed.

Many thanks!
Josh

The config and debug isdn q931 output is below if it helps. I didn't get the 
chance to get the voip ccapi debugs, so please let me know if you need them and 
I'll grab them tomorrow.

!
application
 service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
 !
!
dial-peer voice 5010 voip
 description MVA DID
 destination-pattern 5999
 voice-class codec 1
 session target ipv4:10.10.210.10
 incoming called-number .
 dtmf-relay h245-alphanumeric
 no vad
!
dial-peer voice 2 pots
 service ccm
 incoming called-number 2123945999
 no digit-strip
!
!
!
!
!
!
HQ-RTR(config-dial-peer)#
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8  callref = 0x00A1
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x4180, '2123942123'
Plan:ISDN, Type:Subscriber(local)
Called Party Number i = 0xA1, '2123945999'
Plan:ISDN, Type:National
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: Received SETUP  callref = 0x80A1 
callID = 0x0020 switch = primary-ni interface = User
May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: Application ccm in 
dial-peer 2 not found.  Handing callid 187 to the alternate app .

HQ-RTR(config-dial-peer)#
May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8  callref = 
0x80A1
Cause i = 0x80BF - Service/option not available, unspecified
HQ-RTR(config-dial-peer)#


___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] MVA Fast Busy

[Abdullin Kamil]

 Hi Josh.
You have error in name service "ccm" and "cmm".

application
 service *cmm *

dial-peer voice 2 pots
 service *ccm*

Change name for service to ccm.



2013/5/16 Josh Petro 

> Hi All,
>
> I'm on Volume 1 section 5C which is asking for Mobile Vocie Access
> configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2
> is a fast busy after a few seconds of silence.
>
> I know this has been talked about in the past on this forum, but for the
> life of me I can't find it.
>
> I've followed what was in the workbook exactly and I'm not getting
> anywhere. Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing
> else in the flash directory. Is there something that needs to be
> 'installed' on the router to allow it to see the vxml code on the CUCM?
> I've never been asked to do Mobile Voice Access before, so this is a first.
>
> The CUCM is configured with the Mobile Voice Access number of 5999 and the
> gateway is configured for 4 digits inbound (plus I tested other inbound
> calls and they still work fine).
>
> The Services parameters are correct and MVA is enabled. The voice-class
> codec has G711u and G729r8 and that's it. I'm thinking codec, but I'm not
> sure why.
>
> I can't figure out what I missed.
>
> Many thanks!
> Josh
>
> The config and debug isdn q931 output is below if it helps. I didn't get
> the chance to get the voip ccapi debugs, so please let me know if you need
> them and I'll grab them tomorrow.
>
> !
> application
>  service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
>  !
> !
> dial-peer voice 5010 voip
>  description MVA DID
>  destination-pattern 5999
>  voice-class codec 1
>  session target ipv4:10.10.210.10
>  incoming called-number .
>  dtmf-relay h245-alphanumeric
>  no vad
> !
> dial-peer voice 2 pots
>  service ccm
>  incoming called-number 2123945999
>  no digit-strip
> !
> !
> !
> !
> !
> !
> HQ-RTR(config-dial-peer)#
> May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8  callref =
> 0x00A1
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transfer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Progress Ind i = 0x8583 - Origination address is non-ISDN
> Calling Party Number i = 0x4180, '2123942123'
> Plan:ISDN, Type:Subscriber(local)
> Called Party Number i = 0xA1, '2123945999'
> Plan:ISDN, Type:National
> May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: Received SETUP  callref =
> 0x80A1 callID = 0x0020 switch = primary-ni interface = User
> May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: Application ccm in
> dial-peer 2 not found.  Handing callid 187 to the alternate app .
>
> HQ-RTR(config-dial-peer)#
> May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8
>  callref = 0x80A1
> Cause i = 0x80BF - Service/option not available, unspecified
> HQ-RTR(config-dial-peer)#
>
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>



-- 
С уважением,
Камиль Абдуллин
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] MVA Fast Busy

[ikizoo hello]

application service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
dial-peer voice 2 pots service ccm
ccm ---> cmm ?
Date: Wed, 15 May 2013 23:48:40 -0400
From: josh.pe...@gmail.com
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] MVA Fast Busy

Hi All,
I'm on Volume 1 section 5C which is asking for Mobile Vocie Access 
configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2 is 
a fast busy after a few seconds of silence. 

I know this has been talked about in the past on this forum, but for the life 
of me I can't find it.
I've followed what was in the workbook exactly and I'm not getting anywhere. 
Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing else in the 
flash directory. Is there something that needs to be 'installed' on the router 
to allow it to see the vxml code on the CUCM? I've never been asked to do 
Mobile Voice Access before, so this is a first.

The CUCM is configured with the Mobile Voice Access number of 5999 and the 
gateway is configured for 4 digits inbound (plus I tested other inbound calls 
and they still work fine).

The Services parameters are correct and MVA is enabled. The voice-class codec 
has G711u and G729r8 and that's it. I'm thinking codec, but I'm not sure why.
I can't figure out what I missed.

Many thanks!Josh
The config and debug isdn q931 output is below if it helps. I didn't get the 
chance to get the voip ccapi debugs, so please let me know if you need them and 
I'll grab them tomorrow. 


!application service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml 
!!
dial-peer voice 5010 voip description MVA DID destination-pattern 5999 
voice-class codec 1 session target ipv4:10.10.210.10 incoming called-number . 
dtmf-relay h245-alphanumeric
 no vad!dial-peer voice 2 pots service ccm incoming called-number 2123945999 no 
digit-strip!
!HQ-RTR(config-dial-peer)#May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- 
SETUP pd = 8  callref = 0x00A1 Bearer Capability i = 0x8090A2   
  Standard = CCITT 
Transfer Capability = Speech  Transfer Mode = 
Circuit Transfer Rate = 64 kbit/s Channel ID i = 
0xA98381 Exclusive, Channel 1 
Progress Ind i = 0x8583 - Origination address is non-ISDN  
Calling Party Number i = 0x4180, '2123942123' Plan:ISDN, 
Type:Subscriber(local) Called Party Number i = 0xA1, '2123945999' 
Plan:ISDN, Type:NationalMay 16 03:12:37.874: ISDN Se0/0/0:23 
Q931: Received SETUP  callref = 0x80A1 callID = 0x0020 switch = primary-ni 
interface = User May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: 
Application ccm in dial-peer 2 not found.  Handing callid 187 to the alternate 
app .

HQ-RTR(config-dial-peer)#May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> 
RELEASE_COMP pd = 8  callref = 0x80A1 Cause i = 0x80BF - Service/option 
not available, unspecified
HQ-RTR(config-dial-peer)#



___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com ___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

[OSL | CCIE_Voice] Cucm log

[Dharambir kumar varma]

Hi
Can we delete audit logs on cucm
Which can be seen on Rtmt tool.
Is it possible
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

[OSL | CCIE_Voice] Cucm log

[Dharambir kumar varma]

Hi
Can we delete the audit logs on cucm which is seen on Rtmt tool.
Is it possible ...
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

[OSL | CCIE_Voice] MVA Fast Busy

[Josh Petro]

Hi All,

I'm on Volume 1 section 5C which is asking for Mobile Vocie Access
configuration. What I'm getting when I dial from the PSTN to the HQ Phone 2
is a fast busy after a few seconds of silence.

I know this has been talked about in the past on this forum, but for the
life of me I can't find it.

I've followed what was in the workbook exactly and I'm not getting
anywhere. Now, I'm doing this on my home lab with IOS 12.4.22T5 and nothing
else in the flash directory. Is there something that needs to be
'installed' on the router to allow it to see the vxml code on the CUCM?
I've never been asked to do Mobile Voice Access before, so this is a first.

The CUCM is configured with the Mobile Voice Access number of 5999 and the
gateway is configured for 4 digits inbound (plus I tested other inbound
calls and they still work fine).

The Services parameters are correct and MVA is enabled. The voice-class
codec has G711u and G729r8 and that's it. I'm thinking codec, but I'm not
sure why.

I can't figure out what I missed.

Many thanks!
Josh

The config and debug isdn q931 output is below if it helps. I didn't get
the chance to get the voip ccapi debugs, so please let me know if you need
them and I'll grab them tomorrow.

!
application
 service cmm http://10.10.210.10:8080/ccmivr/pages/IVRMainpage.vxml
 !
!
dial-peer voice 5010 voip
 description MVA DID
 destination-pattern 5999
 voice-class codec 1
 session target ipv4:10.10.210.10
 incoming called-number .
 dtmf-relay h245-alphanumeric
 no vad
!
dial-peer voice 2 pots
 service ccm
 incoming called-number 2123945999
 no digit-strip
!
!
!
!
!
!
HQ-RTR(config-dial-peer)#
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8  callref =
0x00A1
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x4180, '2123942123'
Plan:ISDN, Type:Subscriber(local)
Called Party Number i = 0xA1, '2123945999'
Plan:ISDN, Type:National
May 16 03:12:37.874: ISDN Se0/0/0:23 Q931: Received SETUP  callref = 0x80A1
callID = 0x0020 switch = primary-ni interface = User
May 16 03:12:37.882: %CALL_CONTROL-6-APP_NOT_FOUND: Application ccm in
dial-peer 2 not found.  Handing callid 187 to the alternate app .

HQ-RTR(config-dial-peer)#
May 16 03:12:37.890: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8
 callref = 0x80A1
Cause i = 0x80BF - Service/option not available, unspecified
HQ-RTR(config-dial-peer)#
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

[OSL | CCIE_Voice] Phone displaying unregistered

[Dharambir kumar varma]

Hi

we have some phones registered on CUCM 7.0
when we check them on RTMT,some of the phones it display unregistered
even those are ringing.
why ? i am shocked...i am checking in (Callmanager-Device
search-Phone) on RTMT tool.
-- 
 Regards,
 Dharambir Kumar
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] CCIE Voice renamed CCIE Collaboration available Nov 2013

[Rafael Chavantes]

When this is going to be official?
Until when we can do the current exam?
Em 15/05/2013 13:43, "Vik Malhi"  escreveu:

> More info to come- but we've all been waiting a long time to hear some
> news. People in the middle of their studies hoping to pass on the current
> blueprint- your countdown begins now.
> Vik
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] CCIE Voice renamed CCIE Collaboration available Nov 2013

[Martin Sloan]

Thanks,Vik.  Hopefully I can pass on the current blueprint so I'm a 'CCIE -
Voice' and not a 'CCIE Ambiguous Marketing Jargon' :-)


On Wed, May 15, 2013 at 12:31 PM, Vik Malhi  wrote:

> More info to come- but we've all been waiting a long time to hear some
> news. People in the middle of their studies hoping to pass on the current
> blueprint- your countdown begins now.
> Vik
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] CCIE Voice renamed CCIE Collaboration available Nov 2013

[Otunola Akerele]

wow!!!


On Wed, May 15, 2013 at 5:31 PM, Vik Malhi  wrote:

> More info to come- but we've all been waiting a long time to hear some
> news. People in the middle of their studies hoping to pass on the current
> blueprint- your countdown begins now.
> Vik
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

[OSL | CCIE_Voice] CCIE Voice renamed CCIE Collaboration available Nov 2013

[Vik Malhi]

More info to come- but we've all been waiting a long time to hear some news. 
People in the middle of their studies hoping to pass on the current blueprint- 
your countdown begins now.

Vik

___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com

Re: [OSL | CCIE_Voice] CCIE_Voice Digest, Vol 87, Issue 36

[lou.can...@siriuscom.com]

No need to rename the scripts ... the bacd configuration parameter will define 
the language as 'en' for English. 

paramspace  language  

Example: 

Router(config-app-param)# paramspace english language en

So the 'en' is automatically prefixed to the prompt filename '_bacd_welcome.au' 
to make the complete file name which references the file in flash.


Lou


-

Message: 3
Date: Wed, 15 May 2013 11:15:05 +0530
From: sanity insanity 
To: "ccie_voice@onlinestudylist.com" 
Subject: [OSL | CCIE_Voice] BACD DOUBTS...
Message-ID:

Content-Type: text/plain; charset="iso-8859-1"

Hi Guys,

If there is a  requirement using BACD that If agent did not answer the call in 
10 s , the call should be routed to next agent. If agents are busy they should 
hear " All agents are currently busy..."
The following prompts are available on the tftp serer  ( ip address
X.Y.X.X) and this needs to
taken/downloaded to the flash of router. The prompts available are...

3) en_bacd_music-on-hold.au
4) en_bacd_options_menu.au
5) en_bacd_xferto_operater.au
6) en_bacd_afag.au
7) en_bacd_disconnect.au
8) en_bacd_enter_dest.au
9) en_bacd_invalidoption.au
10) en_bacd_welcome.au

==
Questions:
==

1) Does this mean that we  need to be using the BACD embedded scripts for bacd?

2) Also which one of the above prompts do we download ? The standard cco doc 
for the embedded script shows the following as the welcome prompt 
"welcome-prompt _bacd_welcome.au "  .
Are we requried to rename the prompt?


-MJ

This message (including any attachments) is intended only for
the use of the individual or entity to which it is addressed and
may contain information that is non-public, proprietary,
privileged, confidential, and exempt from disclosure under
applicable law or may constitute as attorney work product.
If you are not the intended recipient, you are hereby notified
that any use, dissemination, distribution, or copying of this
communication is strictly prohibited. If you have received this
communication in error, notify us immediately by telephone and
(i) destroy this message if a facsimile or (ii) delete this message
immediately if this is an electronic communication.

Thank you.
___
For more information regarding industry leading CCIE Lab training, please visit 
www.ipexpert.com

Are you a CCNP or CCIE and looking for a job? Check out 
www.PlatinumPlacement.com