Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
Do you have access to the device you are calling ? Are you sure it is setup and ready to receive the call ? Call it from a handset - you should hear it ring even if the call cannot complete as it's ISDN end to end The problem may be with the provider but it could also be with the terminating device Graham On 23 Jul 2010, at 06:37, Akbar Ali ccie...@gmail.com wrote: Dear Bo , i am pri only for backup of mpls link , but first i am trying to test my link from router itself. but getting error that says no route to destination . provider is not ready to accept that this is their problem. Regards Akbar On Thu, Jul 22, 2010 at 4:55 PM, Bo Gao bga...@gmail.com wrote: Do you need to set isdn incoming-voice voice on D channel? On Thu, Jul 22, 2010 at 2:49 AM, Akbar Ali ccie...@gmail.com wrote: Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: calltrack er disabled *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: Sending SETUP callref = 0x0126 call ID = 0x80B9 switch = primary-net5 interface = User *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q921: User TX - INFO sapi=0 tei=0, ns=16 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0126 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s
Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
Dear Graham , I am calling remote device , i am trying to call on the same router where pri is terminated. with command isdn test call interface serial0/1/0:15 but getting the error no route to destination while debugging isdn standard and q321 . I tried google that says This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired. This cause is supported on a network dependent basis. Regards On Fri, Jul 23, 2010 at 12:52 PM, Graham Hopkins ghopk...@wolf-rock.co.ukwrote: Do you have access to the device you are calling ? Are you sure it is setup and ready to receive the call ? Call it from a handset - you should hear it ring even if the call cannot complete as it's ISDN end to end The problem may be with the provider but it could also be with the terminating device Graham On 23 Jul 2010, at 06:37, Akbar Ali ccie...@gmail.com wrote: Dear Bo , i am pri only for backup of mpls link , but first i am trying to test my link from router itself. but getting error that says no route to destination . provider is not ready to accept that this is their problem. Regards Akbar On Thu, Jul 22, 2010 at 4:55 PM, Bo Gao bga...@gmail.com wrote: Do you need to set isdn incoming-voice voice on D channel? On Thu, Jul 22, 2010 at 2:49 AM, Akbar Ali ccie...@gmail.com wrote: Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15
Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
So if I get this correct you are trying to get the router to call itself using the test call command and the service provider isn't routing the call back to you. If you call this number from a handset do you see the call reaching the router when debugging Q.931 ? Regards Graham On 23 Jul 2010, at 11:04, Akbar Ali wrote: Dear Graham , I am calling remote device , i am trying to call on the same router where pri is terminated. with command isdn test call interface serial0/1/0:15 but getting the error no route to destination while debugging isdn standard and q321 . I tried google that says This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired. This cause is supported on a network dependent basis. Regards On Fri, Jul 23, 2010 at 12:52 PM, Graham Hopkins ghopk...@wolf-rock.co.uk wrote: Do you have access to the device you are calling ? Are you sure it is setup and ready to receive the call ? Call it from a handset - you should hear it ring even if the call cannot complete as it's ISDN end to end The problem may be with the provider but it could also be with the terminating device Graham On 23 Jul 2010, at 06:37, Akbar Ali ccie...@gmail.com wrote: Dear Bo , i am pri only for backup of mpls link , but first i am trying to test my link from router itself. but getting error that says no route to destination . provider is not ready to accept that this is their problem. Regards Akbar On Thu, Jul 22, 2010 at 4:55 PM, Bo Gao bga...@gmail.com wrote: Do you need to set isdn incoming-voice voice on D channel? On Thu, Jul 22, 2010 at 2:49 AM, Akbar Ali ccie...@gmail.com wrote: Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote
[OSL | CCIE_Voice] bad problem in configuring isdn pri
Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: calltrack er disabled *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: Sending SETUP callref = 0x0126 call ID = 0x80B9 switch = primary-net5 interface = User *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q921: User TX - INFO sapi=0 tei=0, ns=16 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0126 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839F Exclusive, Channel 31 Called Party Number i = 0x81, '2320635' Plan:ISDN, Type:Unknown *Jul 22 09:05:41.445: ISDN Se0/1/0:15 Q921: User RX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User RX - INFO sapi=0 tei=0, ns=16 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x812 6 Cause i = 0x829F - Normal, unspecified *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User TX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN EVENTd: cc_clear_free_list freeing 0x673576E0 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 EVENT: process_rxstate: ces/callid 1/0x80B 9 calltype 1 CALL_REJECTION *Jul 22 09:05:41.453: ISDN Se0/1/0:15 EVENTd: process_rxstate: cause=0x1F (31), cause_present=1 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 EVENT: process_rxstate: ces/callid 1/0x80B 9 calltype 1 CALL_CLEARED *Jul 22 09:05:41.453: ISDN Se0/1/0:15 EVENTd: process_rxstate:
Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
Akbar Sahab, I cannot see your calling number over the ISDN? Cause i = 0x829F - Normal, unspecified Telco of called party end is rejecting the call. Ash From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Akbar Ali Sent: 22 July 2010 10:50 To: CCIE_Voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] bad problem in configuring isdn pri Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: calltrack er disabled *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: Sending SETUP callref = 0x0126 call ID = 0x80B9 switch = primary-net5 interface = User *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q921: User TX - INFO sapi=0 tei=0, ns=16 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0126 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839F Exclusive, Channel 31 Called Party Number i = 0x81, '2320635' Plan:ISDN, Type:Unknown *Jul 22 09:05:41.445: ISDN Se0/1/0:15 Q921: User RX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User RX - INFO sapi=0 tei=0, ns=16 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x812 6 Cause i = 0x829F - Normal, unspecified *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User TX - RR sapi=0 tei=0 nr=17 *Jul 22
Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
Do you need to set isdn incoming-voice voice on D channel? On Thu, Jul 22, 2010 at 2:49 AM, Akbar Ali ccie...@gmail.com wrote: Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: calltrack er disabled *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: Sending SETUP callref = 0x0126 call ID = 0x80B9 switch = primary-net5 interface = User *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q921: User TX - INFO sapi=0 tei=0, ns=16 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0126 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839F Exclusive, Channel 31 Called Party Number i = 0x81, '2320635' Plan:ISDN, Type:Unknown *Jul 22 09:05:41.445: ISDN Se0/1/0:15 Q921: User RX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User RX - INFO sapi=0 tei=0, ns=16 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x812 6 Cause i = 0x829F - Normal, unspecified *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User TX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN EVENTd: cc_clear_free_list freeing 0x673576E0 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 EVENT: process_rxstate: ces/callid 1/0x80B 9 calltype 1 CALL_REJECTION *Jul
Re: [OSL | CCIE_Voice] bad problem in configuring isdn pri
Dear Bo , i am pri only for backup of mpls link , but first i am trying to test my link from router itself. but getting error that says no route to destination . provider is not ready to accept that this is their problem. Regards Akbar On Thu, Jul 22, 2010 at 4:55 PM, Bo Gao bga...@gmail.com wrote: Do you need to set isdn incoming-voice voice on D channel? On Thu, Jul 22, 2010 at 2:49 AM, Akbar Ali ccie...@gmail.com wrote: Dear all , I am getting unexpected error while configuring isdn pri E1 , that i am not able to understand as provider says everything is right from their side what to do please help me. following is my configuration and errors also ... i tried self test on pri... controller E1 0/1/0 pri-group timeslots 1-31 description +BSNL PRI+ interface Serial0/1/0:15 no ip address encapsulation ppp dialer rotary-group 1 dialer-group 1 isdn switch-type primary-net5 no peer default ip address ppp authentication chap interface Dialer1 ip address 10.130.253.254 255.255.255.0 encapsulation ppp no ip mroute-cache dialer in-band dialer idle-timeout 9 dialer map ip 10.130.253.252 name FIS_HCBLROUTER broadcast dialer load-threshold 1 either dialer-group 1 HO-Rtr#sh log Syslog logging: enabled (0 messages dropped, 105 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 55360 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 55463 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled Trap logging: level informational, 741 message lines logged Log Buffer (4096 bytes): *Jul 22 09:05:01.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:01.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:11.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.697: ISDN Se0/1/0:15 Q921: User TX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:21.701: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:21.705: ISDN Se0/1/0:15 Q921: User RX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User RX - RRp sapi=0 tei=0 nr=16 *Jul 22 09:05:31.697: ISDN Se0/1/0:15 Q921: User TX - RRf sapi=0 tei=0 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: UserIdle: callid 0x80B9 received IS DN_CALL (0x0) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: UserIdle: Call to 2320635 at 64 Kb /s *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: isdn_get_guid: Cannot allocate a G UID (5) *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENT: process_pri_call: call id 0x80B9, n umber 2320635, Guid 0026F91065D9, speed 64, call type DATA, redial No, CSM call No, pdata No *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: process_pri_call: No name in GTD *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Don't know c alling number for redial. *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: fill_cid_table_voice: Created entr y call_id 0x80B9, speed 64, remote 2320635, calling *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: Packet to CC Data *Jul 22 09:05:41.433: 4D000180B91604030800101804000300 *Jul 22 09:05:41.433: FF700900013233323036333504030800 *Jul 22 09:05:41.433: 101803000300 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: isdn_info =1732177424l, call_id=0x80B9 ORIGINATE *Jul 22 09:05:41.433: ISDN Se0/1/0:15 EVENTd: calltrkr_setup_received: calltrack er disabled *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: Sending SETUP callref = 0x0126 call ID = 0x80B9 switch = primary-net5 interface = User *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q921: User TX - INFO sapi=0 tei=0, ns=16 nr=16 *Jul 22 09:05:41.433: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0126 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA9839F Exclusive, Channel 31 Called Party Number i = 0x81, '2320635' Plan:ISDN, Type:Unknown *Jul 22 09:05:41.445: ISDN Se0/1/0:15 Q921: User RX - RR sapi=0 tei=0 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q921: User RX - INFO sapi=0 tei=0, ns=16 nr=17 *Jul 22 09:05:41.453: ISDN Se0/1/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x812 6
