Re: HIP HIP HURRAY!!! :) [7:48156]
That's a lot of beer. Morgan Hansen wrote in message news:[EMAIL PROTECTED]... HURRAY Hahaha:-) Just got back from my CCNA exam dear friends, and wouldnt you know With help from you guys, I managed to ace the test!!! :-) :-) :-) :-) :-) Without help from you all (Chuck, you know your among them right :-) ) I don't know what I would have done, so. BIG UP TO YOU EVERYONE!!! :-) YOURE THE BEST! (Wish I could by you all a round of beer right now:-)) Once again Thanx with a capital T! Best, Morgan Hansen #CCNA (soon to be mcse to :) mailto:[EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=48165t=48156 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: out of band in band [7:46530]
It's a matter of where signaling is used, as I understand it. If signaling/control for the routing of a call happens through the B channels, then it's in-band b/c part of the bandwidth of the bearer channels is taken up by signaling/call control. D channel is considered out-of-band b/c it's not a bearer channel. The voice call/data transfer is not going over this channel. It's just there to handle signaling for the B channels, therefore leaving all the B-channel bandwidth available. SS7 is an out-of-band protocol/network that handles all signaling b/w Telcos to connect and route calls end to end. No voice channels actually go over the SS7 network. It just handles all the overhead in the management of a call. Hope this makes sense. Kris Keen wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Can someone clarify the terms above? D Channel uses Out of Band Signaling, the B Channel uses In Band signaling? Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=46585t=46530 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCNP 2.0 books
I've checked on Amazon and haven't seen any new releases for study guides or exam preps for the 2.0 track. Maybe i'm just not looking hard enough. Does anyone have recommendations or other good sites for BCMSN, BCRAN, and BSCN books? thanks all **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Aggregation?
I'm not sure I need an aggregation solution (6400, 7200, 7500, 1 series) to do this, and maybe some of you may point me in the right direction. Simply, what is your suggestion for connecting 2 T1 point to point connections between two routers, running ONE IP address each? What series supports this? I haven't had much luck looking in the right areas on Cisco's site, as I'm new to it. I'd appreciate any input. Thanks group! brian **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2505 Router/Hub
Hey all; Just brought up a router straight out of the box with 11.0 IOS on it. It's got 2 Serial, AUX, CON, and 8 ethernet ports(hub). Now, when i'm looking at the interfaces in IOS, it says that I've got an E0 interface. Where I'm a little lost is, where is this interface? I've looked at documentation on the CISCO site, but haven't put it together yet. Would Int E0 be the first of the 8 ethernet ports on the Hub section of the Router?? That doesn't seem right to me, so if anyone has one of these routers, or ideas, I'd appreciate it. Thanks group. brian ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Color codes/Pinouts
I think I found the pinouts listed on the cisco web site for DB9 to RJ45 module (for console connection) but can anyone give me the color scheme? Like Blue to one, Brown to two, yellow to three, etc? I'd really appreciate it. thanks. ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Any difference between secondary address and subinterface for a port?
um...I think cisco stated that secondary addresses will not be supported in some future IOS releases, so.. that's a decent reason not to use them. "Frank Jordan" [EMAIL PROTECTED] wrote in message 8n8um0$5cn$[EMAIL PROTECTED]">news:8n8um0$5cn$[EMAIL PROTECTED]... Under what circumstance should we choose one of them but not the other? Thanks in advance. ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] --- ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
