Re: Cisco 2500 Boot
turn off hardware flow control (set it to no) ""Luke Everett"" [EMAIL PROTECTED] wrote in message 002101c0614a$4cb55400$[EMAIL PROTECTED]">news:002101c0614a$4cb55400$[EMAIL PROTECTED]... I have 3 different Cisco 2500 routers. When I boot them through = Hyperterminal I get what is below. It does not allow me to hit enter, = nothing happens. I have it configured as 9600 Baud, 8 Data Bits, parity = - none, 1 stop bit, flow control - hardware. It is the same for all = three of the routers. How can I get these routers running? I know they = work because I have used them with a laptop before. -=20 Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner Image text-base: 0x0302F3B0, data-base: 0x1000 cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of = memory. Processor board ID 02084157, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read ONLY) IP multicast fastswitching not allowed on X.25 interfaces IP multicast fastswitching not allowed on X.25 interfaces Press RETURN to get started! %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state = to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco 2500 Boot
Luke, Make sure you select the following settings in HyperTerminal: Bits Per Second:9600 Date Bits: 8 Parity: None Stop Bits: 2 Flow Control: None Ash -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Luke Everett Sent: Friday, December 08, 2000 7:09 PM To: [EMAIL PROTECTED] Subject: Cisco 2500 Boot I have 3 different Cisco 2500 routers. When I boot them through = Hyperterminal I get what is below. It does not allow me to hit enter, = nothing happens. I have it configured as 9600 Baud, 8 Data Bits, parity = - none, 1 stop bit, flow control - hardware. It is the same for all = three of the routers. How can I get these routers running? I know they = work because I have used them with a laptop before. -=20 Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner Image text-base: 0x0302F3B0, data-base: 0x1000 cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of = memory. Processor board ID 02084157, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read ONLY) IP multicast fastswitching not allowed on X.25 interfaces IP multicast fastswitching not allowed on X.25 interfaces Press RETURN to get started! %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state = to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cisco 2500 Boot
In case the previous two postings won't correct your problem, try the cable. I had a very similar problem. I couldn't get in for nothing. I saw everything scroll but couldn't do anything. Although, I was able to Ctrl-break during boot process to get to the prompt. Then nothing again. In my case it was the cable. Once switched, I was able to resume. If not, you can try changing the DB-connector. Since you mentioned your laptop, there is a possibility the cable and/or the connector were slightly damaged from connecting and disconnecting. Bart ""Ash Aslam"" [EMAIL PROTECTED] wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Luke, Make sure you select the following settings in HyperTerminal: Bits Per Second: 9600 Date Bits: 8 Parity: None Stop Bits: 2 Flow Control: None Ash -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Luke Everett Sent: Friday, December 08, 2000 7:09 PM To: [EMAIL PROTECTED] Subject: Cisco 2500 Boot I have 3 different Cisco 2500 routers. When I boot them through = Hyperterminal I get what is below. It does not allow me to hit enter, = nothing happens. I have it configured as 9600 Baud, 8 Data Bits, parity = - none, 1 stop bit, flow control - hardware. It is the same for all = three of the routers. How can I get these routers running? I know they = work because I have used them with a laptop before. -=20 Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner Image text-base: 0x0302F3B0, data-base: 0x1000 cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of = memory. Processor board ID 02084157, with hardware revision Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read ONLY) IP multicast fastswitching not allowed on X.25 interfaces IP multicast fastswitching not allowed on X.25 interfaces Press RETURN to get started! %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state = to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state = to down %SYS-5-CONFIG_I: Configured from memory by console %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE = (fc1) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 05-Apr-99 19:58 by jaturner _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
