Re: [Cooker] XF 4,1 3D accelleration
richard == richard [EMAIL PROTECTED] writes: richard hi all richard can some tell me if the 3d accelleration is a mandrake addon or not.? richard I cannot get X running with the 2.4.21mdk, it freezes the machine as X richard starts.# richard the generic kenel 2.4.18 compiles and runs, but the graphics are richard noticeably slower... grahics card is ATI Radeon VE richard AT least running ext3 reduces file damage when running both 17-20 and richard 17-21 It appears that XFree4.1 drm is not compatible with XFree4.2 :((( /me wonders when the XFree people will learn one of: - made drm compatible between minor released (preferred) - be able to detect that you have the drivers for the wrong version and refuse to use it (at least that ) Later, Juan. -- In theory, practice and theory are the same, but in practice they are different -- Larry McVoy
Re: [Cooker] XF 4,1 3D accelleration
OS [EMAIL PROTECTED] writes: I still have no accelleration here on my Rage Mobility Pro chipset using I don't known Rage Mobility Pro chipset, what gives lspcidrake output ? François.
Re: [Cooker] XF 4,1 3D accelleration
Hi Francois, using an ATI Radeon VE On Wed, 2002-02-27 at 10:49, François Pons wrote: OS [EMAIL PROTECTED] writes: I still have no accelleration here on my Rage Mobility Pro chipset using I don't known Rage Mobility Pro chipset, what gives lspcidrake output ? . agpgart : Advanced Micro Devices [AMD]|AMD-751 [Irongate] System Controller unknown : Advanced Micro Devices (AMD)|AMD-751 PCI to PCI bridge unknown : Advanced Micro Devices (AMD)|AMD-756 PCI to ISA bridge unknown : Advanced Micro Devices (AMD)|AMD-756 (Viper) Bus Master IDE controller unknown : Advanced Micro Devices (AMD)|AMD-756 Power Management Controller usb-ohci: Advanced Micro Devices (AMD)|AMD-756 PCI to USB Open Host Controller es1371 : Ensoniq|CT5880 ne2k-pci: Winbond Electronics Corp|W89C940 8139too : Realtek|RTL-8139 Card:ATI Radeon : ATI|Radeon QY It definatly run a little slower on the generic 2.4.18 kernel, X crashes and hangs the machine on 2.4.17-21mdk, 2.4.17-2mdk is OK -- Best regards Richard Bown
Re: [Cooker] XF 4,1 3D accelleration
It works here on my inspiron 8000 with Rage Mobility Pro. Do you have your display set to 16bit? Here's my xf86config if it helps. On Tuesday 26 February 2002 16:15, OS wrote: Hello, I still have no accelleration here on my Rage Mobility Pro chipset using kernel-2.4.17-21mdk and XF 4.2.0-7mdk. glxinfo reports direct rendering: No and gears reports a frame rate of 90/sec ! agpgart is loaded but reports no users. If I manually load r128 agpgart then reports 1 user, but still no 3D accelleration. Owen On Tuesday 26 Feb 2002 4:02 pm, you wrote: richard [EMAIL PROTECTED] writes: hi all can some tell me if the 3d accelleration is a mandrake addon or not.? No, if you use XF 4.2 (not 4.1) and current kernel it should work, if you mix an old version of XFree with current kernel, do not activate DRI (hardware 3D). François. -- ^^^ Jason Straight -- President BlazeConnect Internet Services -- Cheboygan Michigan ISP: www.blazeconnect.net Products: www.blazeconnect.com Phone: 231-597-0376 -- Fax: 231-597-0393 # File generated by XFdrake. # ** # Refer to the XF86Config(4/5) man page for details about the format of # this file. # ** Section Files RgbPath /usr/X11R6/lib/X11/rgb # Multiple FontPath entries are allowed (they are concatenated together) # By default, Mandrake 6.0 and later now use a font server independent of # the X server to render fonts. FontPath unix/:-1 EndSection # ** # Server flags section. # ** Section ServerFlags # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging #NoTrapSignals # Uncomment this to disable the CrtlAltBS server abort sequence # This allows clients to receive this key event. #DontZap # Uncomment this to disable the CrtlAltKP_+/KP_- mode switching # sequences. This allows clients to receive these key events. #DontZoom # This allows the server to start up even if the # mouse device can't be opened/initialised. AllowMouseOpenFail EndSection # ** # Input devices # ** # ** # Keyboard section # ** Section InputDevice Identifier Keyboard1 Driver Keyboard Option AutoRepeat 250 30 Option XkbRules xfree86 Option XkbModel pc105 Option XkbLayout us EndSection # ** # Pointer section # ** Section InputDevice Identifier Mouse1 Driver mouse Option ProtocolPS/2 Option Device /dev/psaux Option Emulate3Buttons Option Emulate3Timeout50 # ChordMiddle is an option for some 3-button Logitech mice #Option ChordMiddle EndSection Section Module # This loads the DBE extension module. Loaddbe # This loads the Video for Linux module. Loadv4l Loadglx Loaddri # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection extmod #Option omit xfree86-dga EndSubSection # This loads the Type1 and FreeType font modules Loadtype1 Loadfreetype EndSection Section DRI Mode0666 EndSection # ** # Monitor section # ** # Any number of monitor sections may be present Section Monitor Identifier Generic|Generic Laptop Display Panel 1400x1050 VendorName Generic ModelName Unknown # HorizSync is in kHz unless units are specified. # HorizSync may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. HorizSync 31.5-90 # VertRefresh is in Hz unless units are specified. # VertRefresh may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. VertRefresh 59-75 # This is a set of extended mode timings typically used for laptop, # TV
Re: [Cooker] XF 4,1 3D accelleration
Ah ha ! There's a problem here that I had overlooked ! My card is detected as ATI|Rage Mobility M3 AGP 2x but it doesn't work with the r128 drivers. It has to use the good old ati driver. Is this why 3D accelleration is not present ? The output from lspcidrake is : agpgart : Intel Corporation|440BX/ZX - 82443BX/ZX Host bridge unknown : Intel Corporation|440BX/ZX - 82443BX/ZX AGP bridge unknown : LuxSonor Inc.|LS242 MPEG/DVD video decoder yenta_socket: Texas Instruments|PCI1220 CardBus Controller yenta_socket: Texas Instruments|PCI1220 CardBus Controller unknown : Intel Corporation|82371AB PIIX4 ISA unknown : Intel Corporation|82371AB PIIX4 IDE usb-uhci: Intel Corporation|82371AB PIIX4 USB sonypi : Intel Corporation|82371AB PIIX4 ACPI - Bus Master IDE Controller maestro : ESS Technology|ES1968 Maestro 2 Card:ATI Rage Mobility: ATI|Rage Mobility P/M AGP 2x unknown : Virtual|Hub [] Owen On Wednesday 27 Feb 2002 12:30 pm, you wrote: It works here on my inspiron 8000 with Rage Mobility Pro. Do you have your display set to 16bit? Here's my xf86config if it helps. On Tuesday 26 February 2002 16:15, OS wrote: Hello, I still have no accelleration here on my Rage Mobility Pro chipset using kernel-2.4.17-21mdk and XF 4.2.0-7mdk. glxinfo reports direct rendering: No and gears reports a frame rate of 90/sec ! agpgart is loaded but reports no users. If I manually load r128 agpgart then reports 1 user, but still no 3D accelleration. Owen On Tuesday 26 Feb 2002 4:02 pm, you wrote: richard [EMAIL PROTECTED] writes: hi all can some tell me if the 3d accelleration is a mandrake addon or not.? No, if you use XF 4.2 (not 4.1) and current kernel it should work, if you mix an old version of XFree with current kernel, do not activate DRI (hardware 3D). François.
Re: [Cooker] XF 4,1 3D accelleration
Hello, I still have no accelleration here on my Rage Mobility Pro chipset using kernel-2.4.17-21mdk and XF 4.2.0-7mdk. glxinfo reports direct rendering: No and gears reports a frame rate of 90/sec ! agpgart is loaded but reports no users. If I manually load r128 agpgart then reports 1 user, but still no 3D accelleration. Owen On Tuesday 26 Feb 2002 4:02 pm, you wrote: richard [EMAIL PROTECTED] writes: hi all can some tell me if the 3d accelleration is a mandrake addon or not.? No, if you use XF 4.2 (not 4.1) and current kernel it should work, if you mix an old version of XFree with current kernel, do not activate DRI (hardware 3D). François.
Re: [Cooker] XF 4,1 3D accelleration
le mar 26-02-2002 à 16:51, richard a écrit : hi all can some tell me if the 3d accelleration is a mandrake addon or not.? I cannot get X running with the 2.4.21mdk, it freezes the machine as X starts.# the generic kenel 2.4.18 compiles and runs, but the graphics are noticeably slower... grahics card is ATI Radeon VE have a full cooker or take latest XFree as it use gatos drivers ( http://gatos.sourceforge.net/ati.2.php ) -- http://linux-wizard.tuxfamily.org/index.html - A man wrapped up in himself makes a very small package.