[Elecraft] KX1 RX Sensitivity on 20M vs 30M, 40M
i did a lot of measurements due to low sensitivity on 20meter with trackinggenerator and spectrumanalyser the real max peak of the 20meter bandpass filter is at lower frequency (abt 13 MHz) if you align the filter for max gain on 14 Mhz the peak ist abt 6db lower as on 13MHz i did some changes at filter caps but there is a strong influence with the other two filters (40, 30 meter) maybee elecraft has there a new redesign with new filter values - just see with analyser the filter curves.. 73 OE6KYG ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] 40m ECN this past Sunday.
Hello everybody, Kevin, KD5ONS , posted a note saying that I had copied K1EV during the 0200Z 40m ECN last Sunday / Monday. Yes I had under S9 PIGGISH propagation conditions - also W4STK. What Kevin did NOT say , as I think that he is too modest , was that he too was making it over here again - although he was gurgling a bit due to the aurora. And these three gentlemen were about the only stateside people heard here on our CW portion of the band around 0200Z (3 am local) that morning. K2 Magic. 73, Geoff GM4ESD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] fishing rod blanks
Most fishing tackle stores sell fishing rod blanks for those who build their own rods...Long blanks can be a challenge to transport...Fishing rod ferrules in a wide variety of sizes, and ferrule cement can be bought at these tackle stores and the blank can be cut and ferruled...They also sell surf fisherman's sand spikes which is nothing more than a tube with a point on it that can be pushed down into the sand...The fishing rod is then inserted into the tube..Cabella used to sell fishing rod blanks and rod building supplies...I don't know if they still do... Jerry, wa2dkg ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] fishing rod blanks
Take a look at the Moxon Antenna page for sources of cheap rods. http://campus.murraystate.edu/org/msuarc/moxon/index.htm While slightly more expensive, I bought a crappie (the fish, not the adjective) pole from Cabelas for $10.00. Sand spikes are easily made of PVC. Cut one end at 45 degrees. The other end can be slightly flared by heating on a gas grill and forcing heated over a wine bottle. A protruding stainless steel bolt placed at right angles to the tube can be used as a foot rest to drive the spike in the ground. Gil/NN4CW _ Check out Election 2004 for up-to-date election news, plus voter tools and more! http://special.msn.com/msn/election2004.armx ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Help figuring out missing part
So I am going to try to pick up a capacitor locally. I am confused by the value. If I understand it correctly, the manual says caps marked with two digits are the value in pf. Three digits markings use the third as a mutliplier. The manual says its either 27 or 271. In this case wouldnt 27 be 27pF and 271 be 270pF? Sorry for the ignorance ! Rich Yes, I would think so too. I don't inventory parts but the one thing I do is take all caps and stick them in foam and get them all sorted. Guess at that point it would be easy to inventory at least the caps. My first K2 had no missing parts. This one was missing an IC on the control board and one extra of another IC. It is possible that the C198 got lost and I wont rule it out :) But, looks like it is gone regardless. If it is nothing special, I will see if I can find one locally. Have SSB, NB, DSP, 160 and 100 watt to build yet. Thanks for the response. 73, Rich - Original Message - From: k4zm [EMAIL PROTECTED] To: Rich McCabe [EMAIL PROTECTED] Sent: Tuesday, August 24, 2004 6:44 AM Subject: Re: [Elecraft] Help figuring out missing part Rich: That is a rare thing to have a part missing in a kit from Elecraft. I have built twelve K2's and many many K2 options, three K1's and lots of options, and three KX1's and have never had a part missing. I do an inventory of all the parts on even the smallest of kits. I inventory them one bag of parts at a time and dump them into the lid of a shoebox. I sort them in plastic parts boxes and then they are handy when I need them. You might check the envelope that the capacitors came in and see if the 27pf might be in it or it might be mixed up with other caps that look like it. Look at your 270pf capacitors. They mark them 270 for 27pf and 271 for 270pf. They look about the same and it is real easy to confuse them and mix them up. Make sure you have not install the one marked 270 in an place where a 271 should have been used. 73 Jim Younce K4ZM K2 SN: 18 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Off Topic Question
Hi Everyone, I am trying to repair an Autek WM-1 meter that was hit by lighting. The lighting came through the ground return of the coax. It seemed to damage the power supply to the board that does all the work. Nothing else seems damaged except the soot and a few traces were burned off. I am going to repair the traces with wire. But, I need to find an LM7805 in the small wee package the comes with the K2s. I have been to Mouse and all they have is the TO-220 at 1A. Don't need that...just the small we packaged one. Where do I go to find these parts? Lee - K0WA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Help figuring out missing part
Would think the marking for a 27pF capacitor of 271 in the K2 manual may be an error when compared to the markings for similar values. For example: C43 on the RF board, 33pF is marked 330. The usual notation of this type of capacitors is the first two digits are the first part of the value and the last digit is the number of zeros after this with a 0 (zero) meaning no added zero at the end and a 1 indicating an added zero. However it seems that this rule can be broken when it suits the manufacturer. This highlights the benefit of having a capacitance meter either in a DVM or a LCR meter being invaluable when such questions arise to be sure. As a matter of personal policy I checked the value of all capacitors and resistors before insertion when building my K2. Can save a lot of grief later. Bob, G3VVT K2 #4168 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Help figuring out missing part
There is a mistake on the parts list page of Appendix A, RF Section for C198. You will notice that the caps above and below list 20 (or 200) and 33 (or 330) but somehow C198 is 27 (or 271) - WRONG! Should be 27 (or 270). As I remember, when I built mine it was marked with a 27. Rich, KE0X ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 transmit rapid drift on 10 meters
While tuning up my K2 filters with spectrogram and tuning the bandpass filters, I decided to see how the transmitted CW sounded on my K2 Rev B with keying mod, temperature compensated oscillator mod, and KAT1 tuner, so I drug out my 75S-3B receiver to listen as I tuned up into my dummy load. Everything sounded great on 80, 40, 20, and 15 meters, but on 10 meters, yuk. Not only did the output sound low compared to what I was picking up on 15 meters for instance, but there was a very bad frequency drift on key down that never seemed to stop. I was measuring power output using the detector on the DL1 dummy load and it seemed to be putting out the expected power. I also borrowed an HP8640 signal generator from work to test the receiver sensitivity, since my XG1 seems to be not generating the correct levels. With the HP8640 I was able to test the receiver sensitivity on all bands and found that the receiver is functioning very well, even on 10 meters. Any ideas on why the 10 meter transmit signal is so bad? I suspect that 17 meters may be bad also but don't have a receiver covering that band. There is very little circuitry that is not common to both transmit and receive, so, since the receiver is working properly, it seems like perhaps there may be a parasitic oscillation in the transmitter output stages. However, the ever handy test finger placed on all the circuitry reachable from the top of the RF board made no change to the 10 meter transmitted tone or drift. The bang the sides and top test had no effect either. Regards, Bill DeHaven (ex N6ED, and I wish I hadn't let that one expire!) ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Off Topic Question
But, I need to find an LM7805 in the small wee package the comes with the K2s. I have been to Mouse and all they have is the TO-220 at 1A. Search for 78L05 and you'll find plenty of them at Mouser and Digikey. Lyle KK7P ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Off Topic Question
You can order from Elecraft. 78M05, part number E600024 de Joe, aa4nn But, I need to find an LM7805 in the small wee package the comes with the K2s. I have been to Mouse and all they have is the TO-220 at 1A. Don't need that...just the small we packaged one. Where do I go to find these parts? Lee - K0WA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Off Topic Question
Lee, Mouser has them - the designation is '78L05' for the low power package and '7805' for the 1 amp version. Similar numbering is used for the low power/high power versions of most all the 78xx 3 terminal voltage regulators. With that generalization out of the way, Mouser's part number is 512-LM78L05ACZ. 73, Don W3FPR - Original Message - But, I need to find an LM7805 in the small wee package the comes with the K2s. I have been to Mouse and all they have is the TO-220 at 1A. Don't need that...just the small we packaged one. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K1 enthusiast wonders ??
Hi Carl, ( everybody else) I too love my K1. (#1337) It has a funny story behind it too. I had just moved into my (Oops, our.) new QTH and to battle the needs of my newfound CW addiction, (Thanks N2EY.) I decided to put a small portable SW rcvr on the nightstand. A dedicated shack was still in the process of being built from a converted closet that was itself converted from a crawl space beneath the stairs. (Anybody laughing yet?) Early one morning I heard HC1HLO from Santo Domingo, Ecuador...a town which I'd visited just a year earlier. There I was with no xmit capability, very frustrating, to say the least! So I decided to check out eBay for a quick and dirty solution. I grabbed a 4-band K1 with all the options for a steal, tossed up a 40m doublet and viola, I was back OTA. I ran the feedline to my father's room downstairs with the intention of eventually letting him use it for his SWLing. Well, it's been about six months and I'm more than halfway toward my WAS, including a very nice contact with Curt, AH6RE on the heels of the Sunday Elecraft 40m net. I bagged a 1,000 mi./Watt award for that. All on 5 Watts! Now I want my WAS to be all QRP, I love it. Yeah, I now have a K2/100 and a Ten-Tec Jupiter in the main shack, but something always draws me to that K1 in dad's room. (The secondary shack, hi.) 73 de Bert WA2SI P.S.Any AKers want to set up a sked? ;-) - Original Message - From: Carl Bredberg [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Tuesday, August 24, 2004 11:54 AM Subject: [Elecraft] K1 enthusiast wonders ?? It seems the K1 has fallen off the radar screen here on the Elecraft reflecter and I wonder why. I have a K2 which is wonderful for CW ops in my shack, but it is not as stingy with power as my K1 and too valuable a radio to be bouncing around in the field. Also it is significantly bigger when packing into the wilderness. The KX1 is definately a slick little rig. I have had the opportunity to borrow a friends for a week, and although it definately is a great travelling rig, the K1 outputs twice the power, has 4 bands rather than 3, and seems better able to match whatever you can hook up to for an antenna. I use a Paddelette paddle which mounts to the short K1 tilt stand. Darn near as neat as the KX1 plug in paddle. I have a complete station, the K1, a 10 cell AA battery pack, wire antenna, headphones and logbook all in an insulated soft sided lunch bag. This goes everywhere with me and is without exception THE MOST FUN radio I have ever owned, used or heard tell about! If you don't have a K1, borrow one and you will become a believer too. 73 de Carl, K1KID ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Off Topic - Thanks you guys
Thanks a million for setting me straight on the lm78l05 in the TO-92 case. I've had so many wonderfull people contact me. Thanks a million. I'll try Radio Shack...and the I will see where to go from there. Lee - k0wa ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Is the K2-keyer similar to most other Iambic keyers?
Is there a standard setup for the paddles with a keyer? I've just finished building a KX1 and I have a K2 and with both of these the keyer is set up to send dahs with the left paddle and dits with the right paddle. Yet if the bug was the precursor of the present day keyer it seems that the reverse should be the default or normal setting. Anybody help me with this? Pat AB2II -Original Message- From: Ron D'Eau Claire [mailto:[EMAIL PROTECTED] Sent: Monday, August 23, 2004 7:53 PM To: elecraft@mailman.qth.net Subject: RE: [Elecraft] Is the K2-keyer similar to most other Iambic keyers? Actually, the timing is very, very consistent from keyer to keyer. The biggest difference is in choosing whether you want to use Mode A or Mode B keying. Some folks can switch from one mode to another easily, others have a very hard time. So you might want to consider which mode you plan to use. There's a good discussion of the modes at: http://tinyurl.com/6dmc3 Ron AC7AC -Original Message- I'm sure there are timing differences in all of them, but I'm about to (finally, after 27 years of hamming) going to learn how to use paddle. Maybe even the darn Bencher paddles my parents gave me for Christmas. Christmas of 1979, I think. I suppose I could carry the K2 and a small power supply around with me, but I thought maybe just a small keyer would be easier for practice. -- Hisashi T Fujinaka - [EMAIL PROTECTED] BSEE(6/86) + BSChem(3/95) + BAEnglish(8/95) + MSCS(8/03) + $2.50 = latte ___ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KFL1-2 15m/30m and 20m/40m For Sale on eBay
Hi All, These are both assembled, aligned and tested Elecraft KFL1-2 two band filter boards for use with the Elecraft K1 QRP CW transceiver. One has been built for 15m and 30m use and the other for 20m and 40m use. Either can be easily modified for use on 80m, 40m, 30m, 20m, 15m or 17m by simply replacing 13 or fewer capacitors, rewinding two toroids and replacing one crystal. You can get the capacitors and crystals from Elecraft for a reasonable cost. I'm selling both of these boards on eBay for $30.00 Buy It Now! or you can bid on them starting at $25.00 and take your chances that it won't go higher than $30.00 in the end. Shipping is a flat $3.85 to anywhere in the USA. Shipping insurance is optional and costs $1.30. The eBay item numbers are 5716929374 for the 15m/30m board and 5716929575 for the 20m/40m board. Happy bidding! 73, Bill... AIØC ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K1 enthusiast wonders ??
I have a k1 nr 1512. I often say it is like my dog, it is my best friend! Reggie k1 1512, k2 4112 - Original Message - From: Tom Arntzen [EMAIL PROTECTED] To: elecraft@mailman.qth.net Sent: Tuesday, August 24, 2004 2:17 PM Subject: Re: [Elecraft] K1 enthusiast wonders ?? I have K1 nr.1491. I have not seen or tried KX1 , but I find my K1 outstanding for fieldtrip and holiday. Going to buy a small gel cell to go with it . Tom LA1PHA - Original Message - From: Carl Bredberg [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Tuesday, August 24, 2004 5:54 PM Subject: [Elecraft] K1 enthusiast wonders ?? It seems the K1 has fallen off the radar screen here on the Elecraft reflecter and I wonder why. I have a K2 which is wonderful for CW ops in my shack, but it is not as stingy with power as my K1 and too valuable a radio to be bouncing around in the field. Also it is significantly bigger when packing into the wilderness. The KX1 is definately a slick little rig. I have had the opportunity to borrow a friends for a week, and although it definately is a great travelling rig, the K1 outputs twice the power, has 4 bands rather than 3, and seems better able to match whatever you can hook up to for an antenna. I use a Paddelette paddle which mounts to the short K1 tilt stand. Darn near as neat as the KX1 plug in paddle. I have a complete station, the K1, a 10 cell AA battery pack, wire antenna, headphones and logbook all in an insulated soft sided lunch bag. This goes everywhere with me and is without exception THE MOST FUN radio I have ever owned, used or heard tell about! If you don't have a K1, borrow one and you will become a believer too. 73 de Carl, K1KID ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Looking for a K1 + accs.
Well, Ive pretty much talked myself into a K1 but due to physical constraints dont believe I can build it properly. Cant see up close at all and cannot discern colors. So if anyone has a clean, late model K1and needs the wampum to buy a K2 to build then I want to hear from you. Ill pay a realistic price for one but am on a limited budget. I have a KX1 that was built by a well-known builder and now would like a K1 to go with it. Please quote your price including shipping stateside and provide a full description of your rig. Please reply off the list to [EMAIL PROTECTED] Thanks for the BW 72/73 Ron WA5VFA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K1 enthusiast wonders ??
K1KID wrote It seems the K1 has fallen off the radar screen here My only HF rig is the K1 and it suits my needs well. I'm lucky if I get a half hour a week for hamming and I'd prefer to spend that time on the air, not in the rig. But eventually something will need fixing or adjusting -- the output seems low; the frequency jumps 30 khz when the knob gets bumped; the RIT mod still isn't working right -- and opening the K1 doesn't seem so overwhelming. As much as I would love a K2 and a KX1, their complexity intimidates me. Maybe it's just perception: That's something I won't know till I find more money and time. My K1 cost me half what the K2 would have when built to suit, and the KX1 wasn't available when I bought the rig. If I was shopping today, the K1's price and 7-band capability would steer my decision straight to it. I use a padded lunch bag or an amazingly well suited cardboard shipping box for transport. My 7Ah gel is great for home operation, but I'd rather have something slimmer for the days I'm portable. Sometimes I take a pack of 8 AA alkalines. I'm not sold on the KBT1. I desire solar. Scott N1AIA K1 00139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Another Glowing Review of the K2
On Aug 24, 2004, at 4:59 PM, [EMAIL PROTECTED] wrote: Just received the latest issue (9-10/2004) of NCJ (National Contest Journal) with the feature article: Use of Comparative Analysis to Estimate the DX Prowess of HF Receivers, by SP7HT. Again, the only real competition are radios that cost many times more than the K2 - Orion and IC7800. And when the K2 evolves to a two knob true dual VFO/receive radio it will rise to yet another notch. 73, Steve WB6RSE ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K-2 Audio problem
Hello, My K-2 audio sometimes fades completely away. It can happen whether I'm in RX or TX mode. (Yes, the sidetone can fade to faint or no signal.) Sometimes the audio comes back up almost to the original level, sometimes even all the way back. But it fades again before too long. And it happens with an external speaker or headphones, too. This doesn't happen when I've just powered up. In fact, it's probably always more than 15 or 20 minutes but I've never remembered to note the exact time. If the audio stays weak, I can almost always recover it by turning the AF up until the audio makes an odd sound, sort of like a bubble bursting. I may have to rotate the knob to the 3 or 4 o'clock position, and sometimes I go all the way it still doesn't come back. But after it's back, it stays that way for at least a few minutes. The serial number of my K-2 is 9xx (I'm not being discrete or protecting my privacy--I just can't remember don't want to climb the stairs to check on the rig itself ;-) It's a CW-only rig with the I/O, 160M, NB mods. The filter cases were grounded, filters aligned with Spectrogram, several other mods completed last year including installation of the speaker grill cloth (you don't suppose *that's* the problem, maybe the fabric has too tight a weave for the sound to get out??). Well, that probably tips you off to my level of RF sophistication. So, if any of you can suggest what I should check or look for, I'd be very grateful. 72, Max, k0max ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Is the K2-keyer similar to most other Iambic keyers?
On K2 #12, Paddle Normal has dits on the left paddle and dahs on the right. As you said, just like a bug. 73, Bob N6WG ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Photo Album of the build of KX1 SN: 821
The enclosed link will take you to an album of the photos I took while building KX1 SN: 18 this past weekend. It might give you an idea of what the insides of a KX1 look like. Note: I always do a complete inventory before stating any kit no matter large or small. http://f1.pg.photos.yahoo.com/ph/jim_you2002/album?.tok=phXAroBBOihzJ6Ir.dir=/cc00.src=ph 73 Jim Younce K4ZM K2 SN: 18 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KD5ONS, ECN and those Pesky KX1's
Kevin, KD5ONS, ECN Guru made the remark in one of his ECN eMail announcments that the 'Pesky' KX1's always seem to get thru when the K1's and K2's can't and there must be an EleCraft secret behind this. T H E R E I S ! It's the fabled RF Hyper Wavefront Accelerator Circuit that has been kept secret for over 60 years. EleCraft uses this circuit in the KX1's final. Discovered during the Manhatten Project of WWII, this RF circuit accelerates RF electrons past the speed of light. Normal wattmeters can only detect 1/100 of the RF as it speeds past. Therefore, when the wattmeter is reading 5 watts, it's actually 500 watts! Small antennas such as Slinky dipoles, HamSticks, Quads(that's another whole subject) have been known to catch on fire or explode as the RF electrons pile up while waiting to radiate. It's still a mystery how EleCraft acquired this circuit as the Dept of Defense requires a 'Burn Before Reading' clearance for access. So, KX1 owners, keep your antennas waxed and fire hoses standing by while checking into the ECN and keep the power down to a couple hundred watts... 73, Art W6KYK1-2 K1-4 (Now, if I can just get my tongue outta my cheek) ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: Re: [Elecraft] K1 enthusiast wonders ??
...no, your dog is more of a K9 John K7FD http://webpages.charter.net/peanut/ From: k6xr [EMAIL PROTECTED] Date: 2004/08/25 Wed AM 01:39:39 GMT To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K1 enthusiast wonders ?? I have a k1 nr 1512. I often say it is like my dog, it is my best friend! Reggie k1 1512, k2 4112 - Original Message - From: Tom Arntzen [EMAIL PROTECTED] To: elecraft@mailman.qth.net Sent: Tuesday, August 24, 2004 2:17 PM Subject: Re: [Elecraft] K1 enthusiast wonders ?? I have K1 nr.1491. I have not seen or tried KX1 , but I find my K1 outstanding for fieldtrip and holiday. Going to buy a small gel cell to go with it . Tom LA1PHA - Original Message - From: Carl Bredberg [EMAIL PROTECTED] To: Elecraft@mailman.qth.net Sent: Tuesday, August 24, 2004 5:54 PM Subject: [Elecraft] K1 enthusiast wonders ?? It seems the K1 has fallen off the radar screen here on the Elecraft reflecter and I wonder why. I have a K2 which is wonderful for CW ops in my shack, but it is not as stingy with power as my K1 and too valuable a radio to be bouncing around in the field. Also it is significantly bigger when packing into the wilderness. The KX1 is definately a slick little rig. I have had the opportunity to borrow a friends for a week, and although it definately is a great travelling rig, the K1 outputs twice the power, has 4 bands rather than 3, and seems better able to match whatever you can hook up to for an antenna. I use a Paddelette paddle which mounts to the short K1 tilt stand. Darn near as neat as the KX1 plug in paddle. I have a complete station, the K1, a 10 cell AA battery pack, wire antenna, headphones and logbook all in an insulated soft sided lunch bag. This goes everywhere with me and is without exception THE MOST FUN radio I have ever owned, used or heard tell about! If you don't have a K1, borrow one and you will become a believer too. 73 de Carl, K1KID ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K1 enthusiast wonders ??
Carl Bredberg wrote: It seems the K1 has fallen off the radar screen here on the Elecraft reflecter and I wonder why. I have a K2 which is wonderful for CW ops in my shack, but it is not as stingy with power as my K1 and too valuable a radio to be bouncing around in the field. Also it is significantly bigger when packing into the wilderness. The KX1 is definately a slick little rig. I have had the opportunity to borrow a friends for a week, and although it definately is a great travelling rig, the K1 outputs twice the power, has 4 bands rather than 3, and seems better able to match whatever you can hook up to for an antenna. I use a Paddelette paddle which mounts to the short K1 tilt stand. Darn near as neat as the KX1 plug in paddle. I have a complete station, the K1, a 10 cell AA battery pack, wire antenna, headphones and logbook all in an insulated soft sided lunch bag. This goes everywhere with me and is without exception THE MOST FUN radio I have ever owned, used or heard tell about! If you don't have a K1, borrow one and you will become a believer too. 73 de Carl, K1KID I love my K1 sn 1647 dearly! I own a K2 also; but maybe I'm a bit biased because I built the K1 first - I like it better !!! I take it to work with me every day and operate during lunchtime (weather permitting) from the parking lot. I have a padded case with the K1, a 12V 7aH SLA, a solar panel for charging the battery, headphones, key and tools and meter. I have the KAT-1 installed and just love it! It makes using the Hamsticks or hombrewed Buddipole a breeze! I also have a 10 AA battery holder with NiMH AAs that I use when I don't feel like carting the heavier lead acid battery around. I had the K1 internal battery thingie; but took it out. I like the stock speaker better than the smaller one necessary for use with the internal battery. My K1 has 40, 30, 20 and 15 meters installed. I use it just about everyday; and it's a real life saver. There's nothing better than a little lunchtime QRP to burn away stressfull mornings at work! 73 de Larry W2LJ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com