Re: [Elecraft] Fixing partially deaf K2.
Bruce Bowman wrote: Just curious... did you ever get this resolved? I'm not certain yet. Since my original message, I have dropped my AGC voltage to 3.98V, re-adjusted L34, and recalibrated the filters using the most recent notes for using Spectograph, and recalibrated the S-meter. When I connected the K2 to an external antenna on Saturday night, the K2 seemed to be hearing some stations in the DX window of 80m about as well my Grundig Satellite 800 shortwave radio (which was just using its built-in whip). The results are promising but I need more time to listen to stations and compare to my shortwave receivers. While turning the slug of L34 clockwise, the internal signal peaks. Turning it a bit more and the noise to the right of the internal signal begins to drop. About the time it drops the slug appears to bottom out. I am wonders if I may need to change a cap around L34 to bring the point of best S/N ratio to somewhere more in the middle of the slugs travel range. I didn't get any response to whether 2.5V rms on TP1 when the rig is tuned to 80m is withing the expected range or not. For now, I will just have to assume it is. I still think I am getting more of a change in audio level between AGC on and off than I should. To see if the 8V regulator output is causing the problem may require replacing the regulator. I'm not yet sure what voltages/parts I should check in the IF amp or AGC circuit to determine if there is a problem with one of these circuits. Now that the receiver seems to be performing a little better, I will move on to the transmitter. I want to retest the amount of maximum RF I can get from the radio on the various bands and see if the change in VCO output has made any noticeable change. I will also be rewiring T1 and T3 as I don't think they are wound as well as they could be. They could be the cause for the slightly lower RF output (barely 10W) on 10m. -- Cheers! Kevin. http://www.ve3syb.ca/ |"What are we going to do today, Borg?" Owner of Elecraft K2 #2172 |"Same thing we always do, Pinkutus: | Try to assimilate the world!" #include | -Pinkutus & the Borg ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Fixing partially deaf K2.
Don Wilhelm wrote: May I suggest that you build the test oscillator shown in the Troubleshooting appendix of the K2 manual, and use that oscillator to perform the Receiver Signal Tracing steps. I would except I probably don't have the right resistor values. The Cheap 'N Dirty signal tracing from N0SS hasn't turned up any noticeable change in signal at any of the text points. I do have some crystal oscillator packages which I could use with a pot on the output to do create a signal source. The noise generator and 3-band signal generator Elecraft mini-modules are on my Christmas wish list. I'm hoping to find one or both under the tree this year. If not, I'll have to order them myself. I can't tell much about your AGC threshold, but certainly 4.1 volts is too high - set it no higher than 3.8 volts. The Rev. G manual says to set it to 3.8 during the construction phase. The Rev. C and G manuals both say to set it to 3.6V in the signal tracing section. Messages on the mailing list suggest setting the AGC voltage as high as possible as long as you can still get no noticeable change in audio between AGC on and off. Since my 8V regulator is putting out 8.45V, I have decided to use the experimental formula for setting the AGC voltage so I have set it to 3.98V for now. -- Cheers! Kevin. http://www.ve3syb.ca/ |"What are we going to do today, Borg?" Owner of Elecraft K2 #2172 |"Same thing we always do, Pinkutus: | Try to assimilate the world!" #include | -Pinkutus & the Borg ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Elecraft CW Net Report for December 16th & 17th, 2007
Kevin, Try this: http://hamcall.net/call?callsign=ja7axn Regards, kurtt Kurt Pawlikowski, AKA WB9FMC The Pinrod Corporation [EMAIL PROTECTED] (773) 284-9500 http://pinrod.com Kevin Rock wrote: Good Evening, It worked! Moving the forty meter net forward in time allowed many more to check in. Signals were great here but some of the reports for me were not as good. Where I was giving a 579 I was getting a 559 with QSB. Oh well, it worked as well as it could. From my afternoon's reading I found the sun may be starting up again. Plus the shortest day of the year is close at hand. It can only get better from here on out; unless there is a solar storm. Even that improves conditions after thing settle down. One new K3 on the list so they are slowing leaking out to the public. Guess most of them are going to non-CW operators. I did get a DX contact at the end of the twenty meter net: JA7AXN. He gave me a 559 too. His contact information on QRZ is very sparse. What is the URL for JARL (I think that's right)? He said QTH Fukishima but there was a little QSB along with some QRN so I may have missed a letter. His name was Numa of which I am sure. Any assistance? Yesterday, while testing propagation on 40 meters, I thought I was about to work some DX when I heard 6E4LM work RZ0AF. After I got done with 6E4LM I found I should have chased RZ0AF instead :) Even though I have most areas of Russia it is fun to work another. 6E4LM is operating from an island off Baja California which is not all that far from me. Working Vermont is further! Now that my K2 has been upgraded to the B modifications I should try a little DXing. Can anyone give me some time? The lists => On 14050.50 kHz at 2300z: N0SS - Tom - MO - K3 - 008 W0CZ - Ken - ND - K2 - 1031 KL7CW - Rick - AK - KX1 - 798 K9ZTV - Kent - MO - K3 - 0021 NO8V - John - MI - K2 K8DD - Hank - MI - K2 - 850 AB9V - Mike - IN - K2 - 3993 W6ZH - Pete - CA - K1 - 553 K2HYD - Ray - NC - KX1 - 608 KS7D - Mike - FL - K3 - 118QNI #5! K6DGW - Fred - CA - K2 - 4398 KT5E - Jay - CO - K2 - 5037 K9DMV - Joe - IL - K2 - 5628 N0AR - Scott - MN - K2 - 4866 QNI #90!!! JA7AXN - Numa - Japan On 7045 kHz at 0100z: W6ZH - Pete - CA - K1 - 553QNI #85!!! KL7CW - Rick - AK - KX1 - 798 QNI #105 NO8V - John - MI - K2 QNI #10!! W0JFR - John - CO - K2 - 4507 KT5E - Jay - CO - 5037 AB9V - Mike - IN - K2 - 3993 K6PJV - Dale - CA - K2 - 5345 K9DMV - Joe - IL - K2 - 5628 NK6A - Don - CA - K2 - 1217 K8DD - Hank - MI - K2 - 850 Any corrections or additions to the above lists? Send them to me and I'll fix the database. Thank you for the fine turnout this evening. There was some noise, some QSB, and a little QRM but all in all it was a good time. Ah, just looked at the calendar: next Sunday is my sister's birthday. I had better not tell you how old she is because she may hurt me but she is five years older than me :) Since her birthday is two days before Christmas folks would give her one gift for both holidays. She has been upset over that for as long as I've known her! Until next week stay well and stay warm, 73, Kevin. KD5ONS (Net Control Operator 5th Class) P.S. Today is Ludwig van Beethoven's 237th Birthday. Happy Birthday Ludwig! His Seventh symphony is playing as I write. KJR ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Re: K2 and Vista
Glenn, Thank you for the information. That is very reassuring for me. I've ordered the adapter from Elecraft and we'll see what happens when it arrives. To All, My thanks to all who replied including direct email to me. Your responses have been excellent and appreciated. I might mention I am aware of the need to use the special cable as prescribed in the Elecraft manuals. I've used it successfully numerous times with my K2 so I'm confident it is correctly configured. 73, Jim, AB0UK -Original Message- >From: Glenn McNeil <[EMAIL PROTECTED]> >Sent: Dec 13, 2007 10:30 PM >To: [EMAIL PROTECTED] >Subject: K2 and Vista > >Hi Jim, > >I'm using the Elecraft supplied USB/Serial Cable that I ordered with my K3, >to communicate with my K2 using a Toshiba Laptop running Vista Home >Premium...works fine. Incidentally, I bought a cheap local USB/Serial Cable >from Jaycar here in VK Land for about $30 AUD, and it works with the K3 also >with no problems...I have done several firmware updates, and as I cannot use >my K3 at present ( No working Transverter Firmware, but we won't go >there...), I have been playing around with both USB/Serial Cables. They both >appear quiet ( some years ago I had one that made 6 Meter/HF use >impossible ), and I can JUST hear some noise in the K3 when my local cable >is plugged in to it, but I have yet to try the Elecraft one. > >In a nutshell...the Elecraft one works with Vists on a Toshiba and talks to >my K2. > >73 >Glenn >VK4TZL > ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 External Keying
I have configured my computer and paddle according to Figure 8-1 on page 92 of my K2 owner's manual. According to the N3FJP software I connected the keyline to pin 7 of the d-sub and ground to pin 5. I selected INP PDLn and A DET On in the K2 menu. When I turn on the K2 I hear a low frequency steady tone coming from the K2 speaker. When I tell the N3FJP software to send a message, the message is heard but it is not the correct sequence of dots and dashes. N3FJP shows a transistor interface in the help section. However, I am using the two diodes shown in Figure 8-1. Can anyone help me solve this problem? 73, Dave Kent K0TCP K2 #3193 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Elecraft CW Net Report for December 16th & 17th, 2007
Good Evening, It worked! Moving the forty meter net forward in time allowed many more to check in. Signals were great here but some of the reports for me were not as good. Where I was giving a 579 I was getting a 559 with QSB. Oh well, it worked as well as it could. From my afternoon's reading I found the sun may be starting up again. Plus the shortest day of the year is close at hand. It can only get better from here on out; unless there is a solar storm. Even that improves conditions after thing settle down. One new K3 on the list so they are slowing leaking out to the public. Guess most of them are going to non-CW operators. I did get a DX contact at the end of the twenty meter net: JA7AXN. He gave me a 559 too. His contact information on QRZ is very sparse. What is the URL for JARL (I think that's right)? He said QTH Fukishima but there was a little QSB along with some QRN so I may have missed a letter. His name was Numa of which I am sure. Any assistance? Yesterday, while testing propagation on 40 meters, I thought I was about to work some DX when I heard 6E4LM work RZ0AF. After I got done with 6E4LM I found I should have chased RZ0AF instead :) Even though I have most areas of Russia it is fun to work another. 6E4LM is operating from an island off Baja California which is not all that far from me. Working Vermont is further! Now that my K2 has been upgraded to the B modifications I should try a little DXing. Can anyone give me some time? The lists => On 14050.50 kHz at 2300z: N0SS - Tom - MO - K3 - 008 W0CZ - Ken - ND - K2 - 1031 KL7CW - Rick - AK - KX1 - 798 K9ZTV - Kent - MO - K3 - 0021 NO8V - John - MI - K2 K8DD - Hank - MI - K2 - 850 AB9V - Mike - IN - K2 - 3993 W6ZH - Pete - CA - K1 - 553 K2HYD - Ray - NC - KX1 - 608 KS7D - Mike - FL - K3 - 118QNI #5! K6DGW - Fred - CA - K2 - 4398 KT5E - Jay - CO - K2 - 5037 K9DMV - Joe - IL - K2 - 5628 N0AR - Scott - MN - K2 - 4866 QNI #90!!! JA7AXN - Numa - Japan On 7045 kHz at 0100z: W6ZH - Pete - CA - K1 - 553QNI #85!!! KL7CW - Rick - AK - KX1 - 798 QNI #105 NO8V - John - MI - K2 QNI #10!! W0JFR - John - CO - K2 - 4507 KT5E - Jay - CO - 5037 AB9V - Mike - IN - K2 - 3993 K6PJV - Dale - CA - K2 - 5345 K9DMV - Joe - IL - K2 - 5628 NK6A - Don - CA - K2 - 1217 K8DD - Hank - MI - K2 - 850 Any corrections or additions to the above lists? Send them to me and I'll fix the database. Thank you for the fine turnout this evening. There was some noise, some QSB, and a little QRM but all in all it was a good time. Ah, just looked at the calendar: next Sunday is my sister's birthday. I had better not tell you how old she is because she may hurt me but she is five years older than me :) Since her birthday is two days before Christmas folks would give her one gift for both holidays. She has been upset over that for as long as I've known her! Until next week stay well and stay warm, 73, Kevin. KD5ONS (Net Control Operator 5th Class) P.S. Today is Ludwig van Beethoven's 237th Birthday. Happy Birthday Ludwig! His Seventh symphony is playing as I write. KJR ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Looking for KF6K
Hello, Looking for James de KF6K. James, please e-mail me direct. 72 and Thanks, Ron Polityka WB3AAL www.wb3aal.com www.n3epa.org/ K1 - SN 01011 K2 - SN 01392 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] RE: K3 - should data via the RS232 cable work?
Leigh Thanks for the response. you wrote: I have found a number of confusing issues with the DATA A filters. I report them to k3support, and eventually they will get fixed. (Some have already.) If you have reproduceable cases, you can write down the details and send them in. I turned these in and the "Line In" problem. Elecraft acknowledged digital problems. Communication seems difficult on these issues. The "Line In" got fixed but the rest are waiting for attention. The "CWT kills digital TX" is the only new factoid. In the lates release, it seems you can avoid the 1KHz Fc in DATA A by using low/hi instead of center/width. I don't have any problems with Data Mode A, except that Dual PB stops all receive signals. The 1 KHz problem I see is on INPUT to the line in in AFSK mode. It appears that the mode only accepts audio in at around 1 KHz. On the laptop trigger mode, you might try setting VOX. With RTTY done as AFSK, the duty cycle is 100% and I would think that VOX, if they allow it, would work fine. I have heard incidental reports that VOX works in PSK mode which has a 50% duty cycle for its idle tone, and higher for data. The problem is not in triggering, but in sending FSK RTTY mark and space. FSK D mode seems to be the only mode that can use Dual PB. That mode does not accept audio in. You must either send text with the KY command, key morse code or connect a PC’s I/O line to the “FSK IN” line on the K3’s AUX I/O connector. (If this signal originates from an RS232 port, it will require RS232-to-TTL level conversion.) I was hoping that Simon would add keyboard RTTY in addition to keyboard CW to DM780. Bob KD8CGH KX1, K2, K3 and counting ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] RE: K3 - should data via the RS232 cable work?
Simon Fair enough. I'm trying to use your program to ease some on the kinderkrankheiten of the K3 software. I've been trying to find a way to use the Dual PB filter for RTTY. I have tried three approaches: 1. Mode: Data, Data Mode: A You can transmit anywhere in the waterfall. Invoking Dual PB results in no receive signal - waterfall goes blank. 2. Mode rev Data, Data Mode: AFSK There is a strange Line In INPUT filter centered at 1000Hz. If you set the PITCH to 915 in the K3 and your digital software, you can get a signal out UNTIL you invoke Dual PB, then no RF out (although you have receive!). BTW - Both modes are fragile. If you leave CWT on from a previous CW mode they also doesn't produce RF. I have seen very inconsistent results which I think are due to unexpected interactions like this. 3. Data Mode: FSK Dual PB works on receive and on send with KY command. Appears to be robust. Since I use a laptop with my rig I have no parallel or RS232 port lines to trigger FSK, hence my request for a RTTY keyboard capability as the only way I see to use Dual PB. Bob KD8CGH ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Firmware version at time of shipping.
On Dec 16, 2007 8:38 AM, Geoffrey Mackenzie-Kennedy <[EMAIL PROTECTED]> wrote: > Probably a daft question but am I right to assume that the version of > firmware supplied as part of a K3 kit purchased from Elecraft is the latest > released version existing at the time of shipping the kit, or is the kit > supplied with some early version of firmware which has to be updated as part > of the K3's 'alignment'? As I understand it, the K3 is supplied with the latest version, available at the time of packaging / shipping. But note that the firmware is still in active development / maintenance, so you will want to update it to get the latest bug fixes and enhancements. If only to verify that you can do it, while you have the manual in front of you. -Michael, VE3TIX ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Firmware version at time of shipping.
Geoffrey Mackenzie-Kennedy wrote: Probably a daft question but am I right to assume that the version of firmware supplied as part of a K3 kit purchased from Elecraft is the latest released version existing at the time of shipping the kit, or is the kit supplied with some early version of firmware which has to be updated as part of the K3's 'alignment'? You are right, it's the latest version available, Geoff. -- 73, Vic, K2VCO Fresno CA http://www.qsl.net/k2vco ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Another KX1 question
Luc, You can change the display time on the KX-1 between 5 and 60 seconds or always on. See page 65 of the owners manual under LED. Regards, kurtt Kurt Pawlikowski, AKA WB9FMC The Pinrod Corporation [EMAIL PROTECTED] (773) 284-9500 http://pinrod.com luc Favre wrote: When my KX1 switch from transmit to receive the display remains about 2 seconds blank before redisplaying the frequency. Is this behaviour correct ? I'm afraid ist is. I'm right ? Thanks for replies. Luc/F6HJO/HB9ABB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Another KX1 question
When my KX1 switch from transmit to receive the display remains about 2 seconds blank before redisplaying the frequency. Is this behaviour correct ? I'm afraid ist is. I'm right ? Thanks for replies. Luc/F6HJO/HB9ABB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 dust cover
Forget the cover ... I totally rebuilt the shack shelving to accommodate the K3 and a SPE linear. Don't know which equipment will take longer to arrive :-( 73 Stewart G3RXQ Mustn't grumble - Life of Brian ? On Sun, 16 Dec 2007 08:25:33 -0800 (PST), Larry K1UO wrote: > > Got the cover...now need the radio!! > http://www.nabble.com/file/p14363190/Elecraft%2BK3%2BCover.jpeg ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] New K3 F/W - MCU: V 1.49 DSP: V 1.46 NR Improved.AMadded
Hi Joe, Receiving double sideband AM with offset tuning has some unique audio equalization requirements since the low audio frequencies are boosted by 6dB due to the partial remaining sideband. Agreed, but when, for example, trying to fish out weak signals from NA (10kHz steps) between strong EU stations (9kHz channels) on MW, sometimes one does want to shift around the passband. Audio quality is not so important in this case. Many times SSB is better, but sometimes not. At any rate, I personally would prefer to see the bandwidth in terms of RF bandwidth and not AF bandwidth. vy 73 de toby -- DD5FZ (ex 4n6fz, dj7mgq, dg5mgq, dd5fz) K2/10 #885 K2/100 #3248 K3/100 #67 DOK C12, BCC, DL-QRP-AG, JN58td ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 dust cover
Got the cover...now need the radio!! http://www.nabble.com/file/p14363190/Elecraft%2BK3%2BCover.jpeg -- View this message in context: http://www.nabble.com/K3-dust-cover-tp14363190p14363190.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] New K3 F/W - MCU: V 1.49 DSP: V 1.46 NR Improved.AMadded
> With the 6kHz filter it was not possible to set bandwidth > greater than 2.8kHz and/or Hi/lo cut to 3000Hz and 200Hz > using the knobs. That's correct. AM is a double sideband mode and requires equal bandwidth above and below the carrier. Thus with a 6 KHz filter, one would be limited to a 3 KHz (or slightly more depending on the filter skirts) maximum audio frequency. > It might become confusing when one wants to shift the filter > to listen mainly to one side band; On a clear channel with > say 4kHz or when avoiding interference with 2kHz. Receiving double sideband AM with offset tuning has some unique audio equalization requirements since the low audio frequencies are boosted by 6dB due to the partial remaining sideband. Lyle, it might be worth considering a higher high cut/wider bandwidth for receive with offset tuning. If I recall, many of the SW broadcasters are using a "compatible" modulation that is essentially USB with a reduced (-6dB) carrier. In fact, it might even be worth considering "compatible AM" (VSB or SSB with reduced carrier) transmit - after all it's only programming . 73, ... Joe, W4TV > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Toby Deinhardt > Sent: Sunday, December 16, 2007 2:44 AM > To: Lyle Johnson > Cc: elecraft@mailman.qth.net; DaleJ > Subject: Re: [Elecraft] New K3 F/W - MCU: V 1.49 DSP: V 1.46 > NR Improved.AMadded > > > Hallo Lyle, > > > With the 6 kHz roofing filter, you should be able to set HI CUT to > > 3 kHz in AM mode. > > I do not have my radio here, so from memory: > > With the 6kHz filter it was not possible to set bandwidth > greater than > 2.8kHz and/or Hi/lo cut to 3000Hz and 200Hz using the knobs. > Using the > XFIL button 6kHz appeared to be reachable but no bandwidth > between 6kHz > and 2.8kHz. > > If the 3kHz you mention is equal to 6kHz RF bandwidth (is > equal to 3kHz > AF bandwidth?), then I would suggest displaying the RF and not the AF > bandwidth. It might become confusing when one wants to shift > the filter > to listen mainly to one side band; On a clear channel with > say 4kHz or > when avoiding interference with 2kHz. > > vy 73 de toby > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > > ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Visions of sugar plums
Here in Detroit we are in the middle of a snow storm that could bring up to 12 inches by the end of today so I am enjoying a slow morning with my coffee and some time to daydream. Here is a thought for the Elecraft design engineers - a KX1 with a redesigned case that includes a hard cover to protect the controls and display during transportation. This hard cover could then flip around and serve as a prop to provide a small tilt angle for the rig during use. The KXPD1 paddle would probably need to be reworked to accommodate a tilt but that shouldn't be too difficult. (I use a detached paddle with my KX1.) Merry Christmas and 73, Paul - N8XMS ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Firmware version at time of shipping.
Geoff The firmware on mine was right up to date to the version released that week. I would recommend you test and align your K3 with the version that it comes with, then once it is fully working you can update it to the latest version from the web. 73 Dave, G4AON K3/100 #80 = Probably a daft question but am I right to assume that the version of firmware supplied as part of a K3 kit purchased from Elecraft is the latest released version existing at the time of shipping the kit, or is the kit supplied with some early version of firmware which has to be updated as part of the K3's 'alignment'? 73, Geoff GM4ESD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Firmware version at time of shipping.
Probably a daft question but am I right to assume that the version of firmware supplied as part of a K3 kit purchased from Elecraft is the latest released version existing at the time of shipping the kit, or is the kit supplied with some early version of firmware which has to be updated as part of the K3's 'alignment'? 73, Geoff GM4ESD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Local Demos
Wonder that the K3 looks like in person? Sounds like? Works like? Folks who are willing to show their K3 and those that want a little "Kick the Tires" session can make that known on the K3 fourm at < http://www.zerobeat.net/smf/index.php/topic,119.0.html > 73 - K3HRN ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] RE: K3 - should data via the RS232 cable work?
Hi Bob, There would be some disadvantages to sending the RTTY / PSK via the KY command, I honestly think that an external program such as DigiPan, WinWarbler etc. would be a better option. Displaying the text decoded by K3 is another matter. FWIW I don't really have time to add this now, I am trying to get some new analogue SSTV code working before Christmas. If I can send and receive SSTV then I know that January and most of February will be taken up with the supporting software for SSTV such as picture archives, QSL card templates, fancy drawing software and the like. Maybe next year I'll have a better idea for getting the K3 to send RTTY / PSK, but I'll need to be convinced :-) Simon Brown, HB9DRV - Original Message - From: "Robert Benedict" <[EMAIL PROTECTED]> The FSK data mode works with KY commands but not the PSK data mode. I have used FSK with command macros in Ham Radio Deluxe. The DM780 digital modes program, also from Simon Brown, now also supports keyboard CW on the K3. Maybe with a little lobbying Simon will support keyboard RTTY and PSK for the K3. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com