[Elecraft] 30m DX report with KX1 and K3

[Leigh L. Klotz, Jr WA5ZNU]

I took my KX1 outside to see if I could track down a router-ish noise on 
20m, and when I couldn't I switched to 30M as I was using a 30M MFJ 
short loaded whip.  I heard SM4OTI booming in.  I put the KX1 on top of 
the car for ground and gave Steve a call, but no joy.  I came inside and 
got an "QRZ 5N" answer with 5W from my K3 and SteppIR short dipole, and 
completed the QSO with 25W.

So maybe the solar flare is clearing!

Leigh/WA5ZNU

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Prolific drivers and Mac OS

[Alan Bloom]

In my experience, often the primary source of computer RFI is the router
and the cables connected to it.  I have to turn off my router and modem
if I want to operate on HF from the same room as the computer.  No
problem with the computer itself.

Al N1AL


On Fri, 2010-04-09 at 21:00 -0500, Bob McGraw - K4TAX wrote:
> Largely the issue of RFI can be more related to antenna location and the 
> radio/computer location.  The closer the two are the more problems are 
> likely to arise.  The signal strength at a specific location is defined by 
> the inverse square law.  Double the distance and the RF field decreases by a 
> factor of 4.
> 
> I realize that some must use indoor antennas.  In this case, RFI is a tough 
> solution.  Common mode chokes on every cable, both ends, is likely a must. 
> Keep cables as short as practical.  Make sure all pieces of equipment are 
> bonded together and I don't suggest just relying on the shield or drain in 
> the cables to accomplish this task.  If one needs a ground between two 
> pieces of equipment, then one must run a wire between the two.  Do not daisy 
> chain pieces of equipment together.  Establish a common point such as the 
> power supply case ground terminal {it does have one doesn't it?} and each 
> piece of equipment.  The power supply ground terminal should end up with a 
> number of ground connections where each piece of equipment will only have 
> one ground connection.
> 
> I make my ground jumpers from #10 or #12 primary auto wire, crimp a good 
> quality VACO terminal on the ends and then solder the terminals.  Crimping 
> is only good for the mechanical connection and does not provide a reliable 
> low resistance connection.
> 
> Once done and the station is clean, one might be surprised to find that many 
> of the birdies are no longer heard or are of much lower level too.
> 
> 73
> Bob, K4TAX
> 
> 
> 
> 
> - Original Message - 
> From: "lstavenhagen" 
> To: 
> Sent: Friday, April 09, 2010 7:46 AM
> Subject: Re: [Elecraft] Prolific drivers and Mac OS
> 
> 
> >
> > Well, for what it's worth, I'm still trying to get over my prejudice that
> > computers and HF rigs don't mix but that's going with extreme difficulty
> > recently hi hi. I've been experimenting with grounding schemes, chokes and
> > so on with exasperating results with my macs and the K3. At this point,
> > totally ironically, the only thing useful involving a wire between the
> > computer and the rig has been my USB->RS-232 adapter to run the K3 
> > utility.
> > Everything else involves too much RFI to be able to use the rig/computer 
> > for
> > any intended purpose and the cables always seem to hop back out of the rig
> > and back into the storage boxes.
> > Maybe a Faraday cage around the computer would be the next thing to try.
> > Moving to a location where I can put up a real antenna a long ways from 
> > the
> > rig would probably help too, but that's impractical right now hi hi.
> >
> > So I've about thrown in the towel on this (again) hi hi and am about to
> > surrender and just go back to computerless HF ops. The K3's built-in
> > PSK/RTTY decoder/encoder works surprisingly well now that I'm learning how
> > to use it and I need to practice my CW sending anyway.
> >
> > As for the prolific drivers on MacOS X, the 32 bit releases work great 
> > with
> > no problems using my Bill-n-Ted's Excellent adapter from BestBuy. I havn't
> > worked on the apparent problem with the recent 64 bit version, tho, 
> > because
> > the 32 versions already work fine. And the error messages I get when 
> > trying
> > to load it suggest it's a perms thing and not a problem with the driver
> > itself.
> >
> > PS, I did try this with the non-commercial version of MacLoggerDX and
> > everything I tried out with it also worked perfectly with no problems. I
> > just couldn't hear any signals because of the noise hi hi.
> >
> > 73,
> > LS
> > W5QD
> > -- 
> > View this message in context: 
> > http://n2.nabble.com/Prolific-drivers-and-Mac-OS-tp4872457p4876847.html
> > Sent from the [K3] mailing list archive at Nabble.com.
> > __
> > Elecraft mailing list
> > Home: http://mailman.qth.net/mailman/listinfo/elecraft
> > Help: http://mailman.qth.net/mmfaq.htm
> > Post: mailto:Elecraft@mailman.qth.net
> >
> > This list hosted by: http://www.qsl.net
> > Please help support this email list: http://www.qsl.net/donate.html
> > 
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
P

Re: [Elecraft] Prolific drivers and Mac OS

[Bob McGraw - K4TAX]

Largely the issue of RFI can be more related to antenna location and the 
radio/computer location.  The closer the two are the more problems are 
likely to arise.  The signal strength at a specific location is defined by 
the inverse square law.  Double the distance and the RF field decreases by a 
factor of 4.

I realize that some must use indoor antennas.  In this case, RFI is a tough 
solution.  Common mode chokes on every cable, both ends, is likely a must. 
Keep cables as short as practical.  Make sure all pieces of equipment are 
bonded together and I don't suggest just relying on the shield or drain in 
the cables to accomplish this task.  If one needs a ground between two 
pieces of equipment, then one must run a wire between the two.  Do not daisy 
chain pieces of equipment together.  Establish a common point such as the 
power supply case ground terminal {it does have one doesn't it?} and each 
piece of equipment.  The power supply ground terminal should end up with a 
number of ground connections where each piece of equipment will only have 
one ground connection.

I make my ground jumpers from #10 or #12 primary auto wire, crimp a good 
quality VACO terminal on the ends and then solder the terminals.  Crimping 
is only good for the mechanical connection and does not provide a reliable 
low resistance connection.

Once done and the station is clean, one might be surprised to find that many 
of the birdies are no longer heard or are of much lower level too.

73
Bob, K4TAX




- Original Message - 
From: "lstavenhagen" 
To: 
Sent: Friday, April 09, 2010 7:46 AM
Subject: Re: [Elecraft] Prolific drivers and Mac OS


>
> Well, for what it's worth, I'm still trying to get over my prejudice that
> computers and HF rigs don't mix but that's going with extreme difficulty
> recently hi hi. I've been experimenting with grounding schemes, chokes and
> so on with exasperating results with my macs and the K3. At this point,
> totally ironically, the only thing useful involving a wire between the
> computer and the rig has been my USB->RS-232 adapter to run the K3 
> utility.
> Everything else involves too much RFI to be able to use the rig/computer 
> for
> any intended purpose and the cables always seem to hop back out of the rig
> and back into the storage boxes.
> Maybe a Faraday cage around the computer would be the next thing to try.
> Moving to a location where I can put up a real antenna a long ways from 
> the
> rig would probably help too, but that's impractical right now hi hi.
>
> So I've about thrown in the towel on this (again) hi hi and am about to
> surrender and just go back to computerless HF ops. The K3's built-in
> PSK/RTTY decoder/encoder works surprisingly well now that I'm learning how
> to use it and I need to practice my CW sending anyway.
>
> As for the prolific drivers on MacOS X, the 32 bit releases work great 
> with
> no problems using my Bill-n-Ted's Excellent adapter from BestBuy. I havn't
> worked on the apparent problem with the recent 64 bit version, tho, 
> because
> the 32 versions already work fine. And the error messages I get when 
> trying
> to load it suggest it's a perms thing and not a problem with the driver
> itself.
>
> PS, I did try this with the non-commercial version of MacLoggerDX and
> everything I tried out with it also worked perfectly with no problems. I
> just couldn't hear any signals because of the noise hi hi.
>
> 73,
> LS
> W5QD
> -- 
> View this message in context: 
> http://n2.nabble.com/Prolific-drivers-and-Mac-OS-tp4872457p4876847.html
> Sent from the [K3] mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> 


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] PSK31 setup

[George A. Thornton]

Thanks for the info.  That is exactly what I was looking for.  I will go
through this tonight, I am sure that is the answer.

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Don Wilhelm
Sent: Friday, April 09, 2010 1:26 PM
To: George A. Thornton
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] PSK31 setup

George,

I trust you meant QSO instead of QSL - the cards come after the contact.

:-)

Check the menu for MIC SEL when the K3 is in DATA A mode.  If it is set 
to anything other than LINE IN, it will not work from the Line In input.

Once you have set the microphone select menu correctly, go into TX TEST 
(so not RF is generated) and set the controls - either the K3 "MIC" knob

and/or the computer soundcard output to indicate between 4 and 5 bars on

the K3 ALC display.

Once you have that level setup correctly, go ahead and transmit (not in 
TX TEST) - you should have RF output.  Listen on another receiver if you

have any doubts.

73,
Don W3FPR

George A. Thornton wrote:
> Last night I started setting up PSK31 using HRD and DM780.
>
>  
>
> I am using an older Lenovo T60p computer in a port replicator, running
> Windows 7.  I made direct connections using 1/8 stereo audio plugs
> between the line in-out connectors on the K3.  The line out goes to
the
> microphone input in the laptop, and the headphones output on the
laptop
> goes to the line in on the K3.
>
>  
>
> I have things running apparently properly on receive.  I have had no
> problems working the waterfall to find and decode signals.  
>
>  
>
> I have also verified that on transmit the program does go through all
> the motions and does put the K3 into transmit mode.
>
>  
>
> I have not however been able to get a QSL from anyone yet.  I suspect
> there is something obvious that I have forgotten that needs to be done
> in order for the transmit to work properly.
>
>  
>
> I do have the radio in Data and set to Data A.  
>
>  
>
> I am sure I will feel stupid when someone tells me what I am doing
> wrong.  But, since none of you know me personally I am brave enough to
> take the risk.
>
>
>   
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] PSK31 setup

[Don Wilhelm]

George,

I trust you meant QSO instead of QSL - the cards come after the contact. 
:-)

Check the menu for MIC SEL when the K3 is in DATA A mode.  If it is set 
to anything other than LINE IN, it will not work from the Line In input.

Once you have set the microphone select menu correctly, go into TX TEST 
(so not RF is generated) and set the controls - either the K3 "MIC" knob 
and/or the computer soundcard output to indicate between 4 and 5 bars on 
the K3 ALC display.

Once you have that level setup correctly, go ahead and transmit (not in 
TX TEST) - you should have RF output.  Listen on another receiver if you 
have any doubts.

73,
Don W3FPR

George A. Thornton wrote:
> Last night I started setting up PSK31 using HRD and DM780.
>
>  
>
> I am using an older Lenovo T60p computer in a port replicator, running
> Windows 7.  I made direct connections using 1/8 stereo audio plugs
> between the line in-out connectors on the K3.  The line out goes to the
> microphone input in the laptop, and the headphones output on the laptop
> goes to the line in on the K3.
>
>  
>
> I have things running apparently properly on receive.  I have had no
> problems working the waterfall to find and decode signals.  
>
>  
>
> I have also verified that on transmit the program does go through all
> the motions and does put the K3 into transmit mode.
>
>  
>
> I have not however been able to get a QSL from anyone yet.  I suspect
> there is something obvious that I have forgotten that needs to be done
> in order for the transmit to work properly.
>
>  
>
> I do have the radio in Data and set to Data A.  
>
>  
>
> I am sure I will feel stupid when someone tells me what I am doing
> wrong.  But, since none of you know me personally I am brave enough to
> take the risk.
>
>
>   
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Using the 12v OUT Jack

[Iain MacDonnell - N6ML]

On Fri, Apr 9, 2010 at 4:45 PM, Edward Cole  wrote:
> There is no voltage on the jack - so how do you turn it on?
> page 17 says: "provides up to 0.5 A (switched) for use with accessory
> devices."
> Index refers you to page 17
> I looked thru the MAIN and CONFIG menus and found nothing to turn on 12v OUT.
> No voltage by just turning on the radio

Sounds like yours is broken (or your meter is!). Check the fuse, as
George suggested.


> BTW good luck in finding AVI jacks (not listed by DigiKey or
> Mouser).  I see some sub-D jacks that look like one.

Not sure what you mean by "AVI jacks"? If you're referring to a
connector to mate with the K3 "ACC", it's a standard HD15, as used for
VGA monitor connections. Something like Mouser #806-K86X-EA-15P-30
should work. I've bought mine from the local Fry's recently...

~Iain / N6ML
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] LP-PAN and other SDR

[Larry Phipps]

Phil, is this the case for all bands, or just 2m? If it's all bands, make sure 
that the little cable that connects the K3 IF buffer to the rear panel 
connector is seated properly. Also, make sure all the applicable modules are 
enabled in Setup.

Larry N8LP


>
>
> Date: Fri, 09 Apr 2010 11:25:35 -0400
> From: "Phil LaMarche" 
> Subject: [Elecraft] LP-PAN and other SDR
> To: 
> Cc: lp-...@yahoogroups.com
> Message-ID: <56fa9e417074492f951c1e3d263e8...@lamarcheenterpr>
> Content-Type: text/plain; charset="US-ASCII"
>
> Got my K3 back after having the 144 module installed and all hardware
> updates done.  Works wonderful except for one aspect.  I have several SDR
> platforms to use and in every one, the panadaptor base line is below the
> -140 and I can't see the signals.  Worked fine before.  Any ideas?
>  
> Phil
>  
> Philip LaMarche
>  
> LaMarche Enterprises, Inc
>  
> 727-944-3226
> 727-937-8834 Fax
> 727-510-5038 Cell 
>  
> www.w9dvm.com  
>  
> K3 #1605
>  
> CCA 98-00827
> CRA 1701
> W9DVM

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] LP-PAN and other SDR

[Larry Phipps]

Phil, is this the case for all bands, or just 2m? If it's all bands, 
make sure that the little cable that connects the K3 IF buffer to the 
rear panel connector is seated properly. Also, make sure all the 
applicable modules are enabled in Setup.

Larry N8LP


>
>
> Date: Fri, 09 Apr 2010 11:25:35 -0400
> From: "Phil LaMarche" 
> Subject: [Elecraft] LP-PAN and other SDR
> To: 
> Cc: lp-...@yahoogroups.com
> Message-ID: <56fa9e417074492f951c1e3d263e8...@lamarcheenterpr>
> Content-Type: text/plain;charset="US-ASCII"
>
> Got my K3 back after having the 144 module installed and all hardware
> updates done.  Works wonderful except for one aspect.  I have several SDR
> platforms to use and in every one, the panadaptor base line is below the
> -140 and I can't see the signals.  Worked fine before.  Any ideas?
>  
> Phil
>  
> Philip LaMarche
>  
> LaMarche Enterprises, Inc
>  
> 727-944-3226
> 727-937-8834 Fax
> 727-510-5038 Cell  
> www.w9dvm.com   
> K3 #1605
>  
> CCA 98-00827
> CRA 1701
> W9DVM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] PSK31 setup

[George A. Thornton]

Last night I started setting up PSK31 using HRD and DM780.

 

I am using an older Lenovo T60p computer in a port replicator, running
Windows 7.  I made direct connections using 1/8 stereo audio plugs
between the line in-out connectors on the K3.  The line out goes to the
microphone input in the laptop, and the headphones output on the laptop
goes to the line in on the K3.

 

I have things running apparently properly on receive.  I have had no
problems working the waterfall to find and decode signals.  

 

I have also verified that on transmit the program does go through all
the motions and does put the K3 into transmit mode.

 

I have not however been able to get a QSL from anyone yet.  I suspect
there is something obvious that I have forgotten that needs to be done
in order for the transmit to work properly.

 

I do have the radio in Data and set to Data A.  

 

I am sure I will feel stupid when someone tells me what I am doing
wrong.  But, since none of you know me personally I am brave enough to
take the risk.

 

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] SOLD: LP-PAN and E-MU 0202 Package

[W0WOI]

Thank you Hank, and others.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Second receiver options ??

[Richard Zwirko]

Chuck,
In his response to your KRX3 vs LP-PAN question, Tom, W8JI, mentioned
the advantages of diversity reception by adding the KRX3 to your K3.  I use
this feature very often of the lower 3 HF bands and strongly second this
recommendation . Using the KRX3 sub receiver in my K3  with a second receive
antenna, it's amazing to hear audio fading down and out in one ear while
fading up in the other ear with the result being perfect copy.

But another plus from installing the KRX3 sub receiver module is being able
to simultaneously monitor a second frequency. If you chase DX stations, you
know that many of them run split operation, listening to a known range of
frequencies. By monitoring your transmit frequency, if a loud competing
signal is heard on it, you can quickly and easily move the 'B' VFO to a
better TX frequency. Transmitting on a clearer frequency will often improve
chances of working the DX station.

If I had to make the exclusive choice between the KRX3 and LP-PAN I would
choose the sub receiver module. I believe it improves chances of working DX
over what the LP-PAN could do. That's not to say that the LP-PAN features
won't soon be added to my K3.

73,
Rich - K1HTV

= = =

From: callen1155 
Subject: [Elecraft] Second receiver options ??
To: elecraft@mailman.qth.net
Message-ID: <1270763342230-4874082.p...@n2.nabble.com>
Content-Type: text/plain; charset=us-ascii



Hello guys.

I've been using my K3 about a month now and really enjoying it. Since I have
a keen interest in DXing and pulling out weak signals (DXing cw & ragchewing
cw) I'm starting to think about adding the KRX3 second receiver although I
understand that LP-PAN also provides second receiver capability.

I also understand that true K3 'diversity reception' greatly aids weak sig
copy and would only be available with the KRX3 receiver but not with LP-PAN.

Additionally, I use an older, slower desktop for playing radio and would
probably need to a better pc if i go the LP-PAN route, plus the soundcard,
and then the unit itself.

So if you had enough funds for either the KRX3 second receiver or the LPAN
which would you choose. I'm leaning toward the KRX3 but wanted to get the
experts' take on this as well.

Seems that the visual aspect of LP-PAN, while appealing, would be less
beneficial basd on my operating  than the diversity reception.

Is that making sense?

thanks and 73.
chuck
af4xk
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K3 - 15 pin Y-Cable - Thanks info

[Ken Roberson]

Hello,

Thanks to all for the 15 pin Y cable info.

73 Ken K5DNL


  
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Using the 12v OUT Jack

[George & Jan]

I am using the 1/10/08 schematics - it shows a fuse (F2 - 0.6A) for the aux 
12 Out. It is connected after the DC control FET. If the radio is on the 12V 
Out should have voltage.

I'd suggest checking F2 first.

George
AI4VZ

--
There is no voltage on the jack - so how do you turn it on? 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] Using the 12v OUT Jack

[Edward Cole]

There is no voltage on the jack - so how do you turn it on?
page 17 says: "provides up to 0.5 A (switched) for use with accessory 
devices."
Index refers you to page 17
I looked thru the MAIN and CONFIG menus and found nothing to turn on 12v OUT.
No voltage by just turning on the radio
I am trying to power my 6m preamp from this jack as I cannot see 
spending $35 for a special plug for the ACC jack.
BTW good luck in finding AVI jacks (not listed by DigiKey or 
Mouser).  I see some sub-D jacks that look like one.
Radio Shack is useless as source for "anything"
I hope someone knows the solution to the missing voltage at the 12v OUT jack

73, Ed - KL7UW, WD2XSH/45
==
  BP40IQ   500 KHz - 10-GHz   www.kl7uw.com
500-KHz/CW, 144-MHz EME, 1296-MHz EME
DUBUS Magazine USA Rep dubus...@hotmail.com
== 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] LP-PAN and other SDR

[Adam Koczarski]

Make sure you have the correct antenna selected. Also check and see if the
RX antenna is selected by mistake. If you don't have an RX antenna, you get
the symptoms described. DAMHIK :)

Adam
K3ARK

> -Original Message-
> From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
> boun...@mailman.qth.net] On Behalf Of Phil LaMarche
> Sent: Friday, April 09, 2010 8:26 AM
> To: Elecraft@mailman.qth.net
> Cc: lp-...@yahoogroups.com
> Subject: [Elecraft] LP-PAN and other SDR
> 
> Got my K3 back after having the 144 module installed and all hardware
> updates done.  Works wonderful except for one aspect.  I have several
> SDR
> platforms to use and in every one, the panadaptor base line is below
> the
> -140 and I can't see the signals.  Worked fine before.  Any ideas?
> 
> Phil
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] TEST

[Edward Cole]

I have been blocked from access to the list for several days - so trying again

73, Ed - KL7UW, WD2XSH/45
==
  BP40IQ   500 KHz - 10-GHz   www.kl7uw.com
500-KHz/CW, 144-MHz EME, 1296-MHz EME
DUBUS Magazine USA Rep dubus...@hotmail.com
== 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] FS: LP-PAN (K3 version) & E-MU 0202

[W0WOI]

As a package only, a factory wired K3 version of the LP-PAN and E-MU 0202  
audio interface.  Both are less than one month old, excess to my  need.  
Shipped prepaid USPS stateside; $260.
 
Contact Bill off relector;  _w0...@aol.com_ (mailto:w0...@aol.com) , or  
515-386-2262
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - 15 pin Y

[Iain MacDonnell - N6ML]

On Fri, Apr 9, 2010 at 2:32 PM, Ken Roberson  wrote:
> Hello All,
>
>  WOW thanks for the fast response , I'm
> assuming these have all 15 pins hooked up ??

More importantly, you want to make sure that none of the (usually
unused by VGA) pins are shorted to the shield. The cablewholesale.com
one qualifies...

http://n2.nabble.com/HD15-Y-for-splitting-K3-ACC-td3421552.html

Don't know about the other one mentioned... but suspect it's OK too,
based on the recommendations...

~Iain / N6ML
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] EQ per mode?

[Dick Dievendorff]

You can set up a few (admittedly not too many) K3 macros containing EQ value
settings using the TE command and have them available from the front panel
of your K3 with a couple of switch presses.  See the second CUT LO example
at the bottom of the Command Tester/K3 Macros page in K3 Utility Help
(version 1.3.4.3, new on the Elecraft web site yesterday).

73 Dick, K6KR


-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of pd0psb
Sent: Friday, April 09, 2010 8:16 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] EQ per mode?


Oh no, still have to bring a PC!
I thought working *without* Windows was the charm of K3.

Was hoping for a full EQ-per-mode solution,would have made everybody happy
at once :-)

73'
Paul
PD0PSB


>The latest beta firmware has separate EQ for CW. I would like to have it
for all modes as well, not that I >use AM, but for FM RX I certainly don't
want the treble roll-off I prefer on SSB and CW. 
>There is also a new command to set TX EQ programmatically. I suspect that
those who want multiple EQ >settings per mode will need to use a software
application for this.
-- 
View this message in context:
http://n2.nabble.com/EQ-per-mode-tp4875912p4877658.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] LP-PAN and other SDR

[Phil LaMarche]

Got my K3 back after having the 144 module installed and all hardware
updates done.  Works wonderful except for one aspect.  I have several SDR
platforms to use and in every one, the panadaptor base line is below the
-140 and I can't see the signals.  Worked fine before.  Any ideas?
 
Phil
 
Philip LaMarche
 
LaMarche Enterprises, Inc
 
727-944-3226
727-937-8834 Fax
727-510-5038 Cell 
 
www.w9dvm.com  
 
K3 #1605
 
CCA 98-00827
CRA 1701
W9DVM
 
 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Prolific drivers and Mac OS

[David Ferrington, M0XDF]

I don't have any problems with RFI and my K3/Mac at all and I do have some RF 
in my shack.
I do use a microHam DigiKeyer. But I would have thought any opto coupled 
connection and audio transformer isolated connections would be fine.
73 de M0XDF, K3 #174
-- 
A person usually has two reasons for doing something: a good reason and the
real reason. -Thomas Carlyle, historian and essayist (1795-1881)

On 9 Apr 2010, at 13:46, lstavenhagen wrote:

> 
> Well, for what it's worth, I'm still trying to get over my prejudice that
> computers and HF rigs don't mix but that's going with extreme difficulty
> recently hi hi. I've been experimenting with grounding schemes, chokes and
> so on with exasperating results with my macs and the K3. At this point,
> totally ironically, the only thing useful involving a wire between the
> computer and the rig has been my USB->RS-232 adapter to run the K3 utility.
> Everything else involves too much RFI to be able to use the rig/computer for
> any intended purpose and the cables always seem to hop back out of the rig
> and back into the storage boxes.
> Maybe a Faraday cage around the computer would be the next thing to try.
> Moving to a location where I can put up a real antenna a long ways from the
> rig would probably help too, but that's impractical right now hi hi.
> 
> So I've about thrown in the towel on this (again) hi hi and am about to
> surrender and just go back to computerless HF ops. The K3's built-in
> PSK/RTTY decoder/encoder works surprisingly well now that I'm learning how
> to use it and I need to practice my CW sending anyway.
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] EQ per mode?

[pd0psb]

Oh no, still have to bring a PC!
I thought working *without* Windows was the charm of K3.

Was hoping for a full EQ-per-mode solution,would have made everybody happy
at once :-)

73'
Paul
PD0PSB


>The latest beta firmware has separate EQ for CW. I would like to have it
for all modes as well, not that I >use AM, but for FM RX I certainly don't
want the treble roll-off I prefer on SSB and CW. 
>There is also a new command to set TX EQ programmatically. I suspect that
those who want multiple EQ >settings per mode will need to use a software
application for this.
-- 
View this message in context: 
http://n2.nabble.com/EQ-per-mode-tp4875912p4877658.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Prolific drivers and Mac OS

[lstavenhagen]

As I've said to others privately, it's most likely my indoor antenna. So I'm
likely just complaining with the solution already in hand hi hi. Because I
live in apts., I've always been restricted to indoor ants so this goes back
a long ways even back into my PC days.

That said, my macbook pro (the newest generation with the one piece Al
shell) is somewhat quieter than my couple generations old macbook with the
plastic case. That thing really rips up the rigs. 

The fix would clearly be to buy a house and put up a good outside ant., a
solution thats far far outside my budget hi hi. Meanwhile, the workaround
will probably be to just use the built-in decoder/encoder in the K3 for
digital modes. 

But like I said, I'm having no software problems at all, even the demo of
MacLoggerDX works great with my Bill-n-Ted's Excellent adapter and
cocoaModem similarly with the audio cables. 

I might schlep the K3 out portable once with my laptop and just get the ant
as far away from the rig as I can to troubleshoot that aspect of it.

73,
LS
W5QD
-- 
View this message in context: 
http://n2.nabble.com/Prolific-drivers-and-Mac-OS-tp4872457p4877522.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K3 - 15 pin Y

[Ken Roberson]

Hello All,

 WOW thanks for the fast response , I'm 
assuming these have all 15 pins hooked up ??

Thanks Ken K5DNL

  


  
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - 15 Pin Y-Cable

[Joe Subich, W4TV]

Cables Wholesale: 
   http://www.cablewholesale.com/cgi-bin/search.cgi?text=10H1-27708
Altex: 
http://www.altex.com/VGA-Male-to-2-VGA-Females-Y-Adapter-70-568-P142649C10703.
aspx 

73, 

   ... Joe, W4TV 
 


> -Original Message-
> From: elecraft-boun...@mailman.qth.net 
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ken Roberson
> Sent: Friday, April 09, 2010 9:43 AM
> To: Elecraft Elecraft
> Subject: [Elecraft] K3 - 15 Pin Y-Cable
> 
> 
> Hello All,
> 
> Has anyone found a source for 15 pin Y cable ??
> 
> Thanks  Ken K5DNL
> 
> 
>   
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - 15 Pin Y-Cable

[Edward Dickinson, III]

http://www.altex.com/VGA-Male-to-2-VGA-Females-Y-Adapter-70-568-P142649C1070
3.aspx


73,
Dick - KA5KKT



>Hello All,

>Has anyone found a source for 15 pin Y cable ??

>Thanks  Ken K5DNL

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Prolific drivers and Mac OS

[K6LE]

Wow!  what Mac are you using?

I have my iMac (2008 2.8 GHz C2D )  sitting next to my K3 and it is on all the 
time.  

The only noises in the radio that I have experienced are:

A slight hum in the Line In - probably caused by them not being on the same 
plug and/or not bonded together.  Solved it with one of the audio isolators 
that Radio Shack sells for about $15.  Will work on the grounding later.

I get birdies from the ethernet cable - solved by disconnecting it and using 
Wi-Fi.

I hear some nasty birdies from my networked laser printer - I just turn it off 
when not using it.

Other than those solved problems I don't have any interference between the Mac 
and the K3.

I don't know how I could operate "computerless" these days!

Rick
K6LE

On 4/9/2010, at 5:46 , lstavenhagen wrote:

> 
> Well, for what it's worth, I'm still trying to get over my prejudice that
> computers and HF rigs don't mix but that's going with extreme difficulty
> recently hi hi. I've been experimenting with grounding schemes, chokes and
> so on with exasperating results with my macs and the K3. At this point,
> totally ironically, the only thing useful involving a wire between the
> computer and the rig has been my USB->RS-232 adapter to run the K3 utility.
> Everything else involves too much RFI to be able to use the rig/computer for
> any intended purpose and the cables always seem to hop back out of the rig
> and back into the storage boxes.
> Maybe a Faraday cage around the computer would be the next thing to try.
> Moving to a location where I can put up a real antenna a long ways from the
> rig would probably help too, but that's impractical right now hi hi.
> 
> So I've about thrown in the towel on this (again) hi hi and am about to
> surrender and just go back to computerless HF ops. The K3's built-in
> PSK/RTTY decoder/encoder works surprisingly well now that I'm learning how
> to use it and I need to practice my CW sending anyway.
> 
> As for the prolific drivers on MacOS X, the 32 bit releases work great with
> no problems using my Bill-n-Ted's Excellent adapter from BestBuy. I havn't
> worked on the apparent problem with the recent 64 bit version, tho, because
> the 32 versions already work fine. And the error messages I get when trying
> to load it suggest it's a perms thing and not a problem with the driver
> itself.
> 
> PS, I did try this with the non-commercial version of MacLoggerDX and
> everything I tried out with it also worked perfectly with no problems. I
> just couldn't hear any signals because of the noise hi hi.
> 
> 73,
> LS
> W5QD

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] EQ per mode?

[Julian, G4ILO]

The latest beta firmware has separate EQ for CW. I would like to have it for
all modes as well, not that I use AM, but for FM RX I certainly don't want
the treble roll-off I prefer on SSB and CW.

There is also a new command to set TX EQ programmatically. I suspect that
those who want multiple EQ settings per mode will need to use a software
application for this.

-
Julian, G4ILO. K2 #392  K3 #222.
* G4ILO's Shack - http://www.g4ilo.com
* KComm - http://www.g4ilo.com/kcomm.html
* KTune - http://www.g4ilo.com/ktune.html

-- 
View this message in context: 
http://n2.nabble.com/EQ-per-mode-tp4875912p4877143.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] K3 - 15 Pin Y-Cable

[Ken Roberson]

Hello All,

Has anyone found a source for 15 pin Y cable ??

Thanks  Ken K5DNL


  
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Second receiver options ??

[callen1155]

Thank you for the info Tom. I appreciate it.

chuck
73
-- 
View this message in context: 
http://n2.nabble.com/Second-receiver-options-tp4874082p4876892.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KDSP2 F/S or trade

[Mark - W5EZY]

I would like to sell my KDSP2 option w/manual for $150 or trade for a KAF2
plus $100.  This can be a cheap way to get DSP in that K2 wonderbox.  Please
email direct.

-- 
View this message in context: 
http://n2.nabble.com/KDSP2-F-S-or-trade-tp4876835p4876835.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Prolific drivers and Mac OS

[lstavenhagen]

Well, for what it's worth, I'm still trying to get over my prejudice that
computers and HF rigs don't mix but that's going with extreme difficulty
recently hi hi. I've been experimenting with grounding schemes, chokes and
so on with exasperating results with my macs and the K3. At this point,
totally ironically, the only thing useful involving a wire between the
computer and the rig has been my USB->RS-232 adapter to run the K3 utility.
Everything else involves too much RFI to be able to use the rig/computer for
any intended purpose and the cables always seem to hop back out of the rig
and back into the storage boxes.
Maybe a Faraday cage around the computer would be the next thing to try.
Moving to a location where I can put up a real antenna a long ways from the
rig would probably help too, but that's impractical right now hi hi.

So I've about thrown in the towel on this (again) hi hi and am about to
surrender and just go back to computerless HF ops. The K3's built-in
PSK/RTTY decoder/encoder works surprisingly well now that I'm learning how
to use it and I need to practice my CW sending anyway.

As for the prolific drivers on MacOS X, the 32 bit releases work great with
no problems using my Bill-n-Ted's Excellent adapter from BestBuy. I havn't
worked on the apparent problem with the recent 64 bit version, tho, because
the 32 versions already work fine. And the error messages I get when trying
to load it suggest it's a perms thing and not a problem with the driver
itself.

PS, I did try this with the non-commercial version of MacLoggerDX and
everything I tried out with it also worked perfectly with no problems. I
just couldn't hear any signals because of the noise hi hi.

73,
LS
W5QD
-- 
View this message in context: 
http://n2.nabble.com/Prolific-drivers-and-Mac-OS-tp4872457p4876847.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 KXV3-RXA Mod

[VE3NFK]

Thanks for the replies - and Don, I'll leave it in until I next open the rig 
_ I haven't noticed any detriment - but there is no point in having them
both in.

73  John VE3NFK
-- 
View this message in context: 
http://n2.nabble.com/K3-KXV3-RXA-Mod-tp4873179p4876689.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Second receiver options ??

[Tom W8JI]

Chuck,

LP Pan mostly is a spot and click assist to operating, it 
really will not be a better or different second signal 
channel than the K3's audio. There is, of course, no weak 
signal diversity improvement from running LP Pan in one ear 
and the K3 in the other.

Stereo diversity reception that allows significantly 
enhanced weak signals requires significantly different 
antennas for each receiver input and also requires nearly 
exact duplicates of phase, signal processing time delay, and 
bandwidth in both receiver channels for maximum effect. 
Average signal-to-noise of the desired signal on both 
antennas also has to be about the same for maximum effect. 
It does no good to combine mostly noise from one ear with 
signal and some noise from the other.

There is a little improvement from antennas on each channel 
being different in polarization when spacing is close, but 
by far the most significant improvement occurs when the 
receiving antennas are a fairly large distance apart in 
wavelengths. Keep in mind "polarization" does not mean the 
physical layout of the antenna, but rather the actual 
response. For example my Beverages, although long horizontal 
wires, have only vertical polarization in the front lobes. 
If I diversity pair a Beverage with a vertical array, they 
must have large spatial separation (over 1 wavelength) or 
enhancement is far from optimum.

Another use of stereo is filling in holes in receiving 
directional patterns, like listen west and northeast at the 
same time using two different directional patterns.

73 Tom 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] EQ per mode?

[rfenabled]

Oh yes please
Gary
Vk4FD
--Original Message--
From: pd0psb
Sender: elecraft-boun...@mailman.qth.net
To: Elecraft
Subject: [Elecraft] EQ per mode?
Sent: Apr 9, 2010 6:32 PM



Just wondering: is EQ-per-mode still on the list?

Since K3 has also found use for AM-sync BC and VHF FM, different settings
per mode would be even more welcome.

Some time ago I had the impression it was quite high on The List :-)

73'
Paul
PD0PSB
-- 
View this message in context: 
http://n2.nabble.com/EQ-per-mode-tp4875912p4875912.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


Sent via BlackBerry® from Telstra
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] EQ per mode?

[pd0psb]

Just wondering: is EQ-per-mode still on the list?

Since K3 has also found use for AM-sync BC and VHF FM, different settings
per mode would be even more welcome.

Some time ago I had the impression it was quite high on The List :-)

73'
Paul
PD0PSB
-- 
View this message in context: 
http://n2.nabble.com/EQ-per-mode-tp4875912p4875912.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html