Don,
I installed the .1 microfarad capacitor at C30, but this didn’t change the
output.
After testing the C30 fix, I subsequently changed R30 to 33 ohms and R11 to 4.7
ohms. This did change things, but did not entirely resolve the problem.
At 13.8V input, my power meter shows 3.0 watts on both 20M and 40M.
When I lower the input voltage to 9.0 volts, the meter shows 1.4 watts on 40M
and 1.7 watts on 20M.
I guess this is within or nearly within specs, but it’s odd that there is more
output on 20M than on 40M.
Anything else I should try, or should I just use it like this for a while?
Thanks again,
Lee
KG5VU
On Jun 17, 2015, at 1:02 PM, Don Wilhelm w3...@embarqmail.com wrote:
Lee,
Yes, I would change that capacitor - there is a chance that it will increase
the output of the DDS and solve your power output problem.
There is a difference in some KX1s due to care during construction, component
tolerances, and a host of other factors.
Make certain you counted the toroid turns correctly - a straight wire through
the core is one turn, a full wrap around the core is 2 turns.
Count the turns that go through the core center.
If all else fails, you can install the KX1 power mod. If you have a good
stock of 1/4 watt resistors you may not need to order the kit. Change R11 to
4.7 ohms and R30 to 33 ohms.
If those steps do not solve the power output situation, send me an off-list
email and we can make comparison measurements with my KX1.
The KX1 audio is not 'earbusting', but is normally adequate. Yes, you may
want to try headphones or earbuds with a higher SPL rating.
The Quick Reference is the only place in the KX1 manual where SLO, SHI, and
CAL are mentioned - I guess someone overlooked updating that portion of the
manual since the VERY early days of the KX1. Look at the listing of menu
items on page 65 and you will see DDS, BFO, and SIG to make those settings.
This has been true since firmware rev 1.01. 1.02 is the latest version.
73,
Don W3FPR
On 6/17/2015 10:58 AM, KG5VU wrote:
Hi,
I just finished building KX1 Serial Number 2879 which is the standard
20M/40M version. It's a great little rig but, I have a few issues, one
major and two minor:
A) On final testing I only had about 2.5W on 20M and 2.0W on 40M with power
supply at 13.8V. I tried to compress the winding on L2, as suggested, but
this only degraded the output slightly (2.2W on 20M and 1.8W on 40M).
Checked the components on the board against the schematic and everything
checked out OK. Any ideas on what else I should try? Any idea what RF
voltage levels I should see at each stage? (I have several decent
oscilloscopes for testing if need be.)
B) The receiver is sensitive (I can hear 0.1 microvolt RF signal on 20 40)
but the audio level (particularly for weak signals) is pretty low unless I
advance the AF Gain control to full clockwise. Is this normal? Do I just
need to experiment with different sets of ear-buds?
C) The firmware on my KX1 is version 1.02. The Menu on my unit is different
than the Manual. It does not include SLO, SHI or CAL. Instead there are
SIG, DDS and BFO. Are support documents for revised version available?
For background, I had no difficulty during assembly. The KX1 passed all
tests except the transmit power output.
I did make one mistake during assembly however. I mistakenly inserted a .1
microfarad capacitor at C30 instead of a .01 microfarad capacitor. Since
everything seemed to be working, so I have not corrected this issue. Think
this could be significant?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
