RE: [Elecraft] K3 Help
I am using COM 1 and it is the only one available in the drop down list of the K3 utility. The streaming characters stop when I unplug the COM cable from the rear of the rig. This tells me that the K3 is for some reason sending a solid stream of characters that can be seen in the command tester page. The firmware page continues to say K3 is not responding or unable to communicate with K3. I have no idea why the rig would be sending a stream of characters. Mike Dick Dievendorff wrote: The K3 Utility command tester is showing you the characters it is receiving. Something is sending data over that COM port. Please make sure that the COM port you have selected in the PORTS tab is the one connected to your K3. Try turning your K3's power off (by removing the power connector, if necessary) and see if the data streaming stops. If it doesn't, the data isn't coming from your K3; maybe the COM port is connected to something else, or perhaps there's a defective cable. Dick, K6KR -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mike N8XPQ Sent: Friday, July 04, 2008 6:01 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 Help I have noticed something new as well. When I click on the command tester tab, the window pops up and a strange y with 2 dots over top of it are rapidly scrolling across the screen and filling it up.H very strange? When I disconnect the serial cable from the rig, it stops. Mike Mike N8XPQ wrote: My K3 is stuck in MCU LD mode. I have tried everything in reference to the com port settings. The K3 utility continues to say K3 not communicating. I have the latest version of the utility and have attempted to re-load 2.10 firmware as well as 2.13 with no luck. I have also tried forcing a firmware load per the manual and directions in the firmware help files. Still no luck. Any ideas? I really don't want to be with a dead rig all weekend. Thanks, Mike N8XPQ - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Help-tp18287766p18288055.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Help-tp18287766p18291119.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Help
I have confirmed that the Com port is functioning properly as I have run the programming software for my HT on it. I have also tried several different computers as well as laptops. I am convinced that the problem lies in the K3. It refuses to communicate with the PC's. It seems to be stuck in the MCU loading state and is not accepting any commands from the K3 loader software. The last time the rig was functional it was operating on firmware version 2.10 and I had noticed a possible problem communicating with it via the com port. I attempted to upgrade to the latest firmware and this is now where I am stuck. When the K3 loader starts up it displays a message stating it is unable to communicate with K3. At times when I display the command tester screen it will show a strange y character with 2 dots on top of it scrolling across and filling the screen. That will stop if I disconnect the Com cable from the back of the rig. When I re-connect it and refresh the command tester screen it starts up again displaying the strange character. I have taken out the K3IO board and re-seated it in the rig and the problem persists. ARGH Any help or further suggestions PLEASE!:-) Thanks in advance, Mike N8XPQ Mike N8XPQ wrote: My K3 is stuck in MCU LD mode. I have tried everything in reference to the com port settings. The K3 utility continues to say K3 not communicating. I have the latest version of the utility and have attempted to re-load 2.10 firmware as well as 2.13 with no luck. I have also tried forcing a firmware load per the manual and directions in the firmware help files. Still no luck. Any ideas? I really don't want to be with a dead rig all weekend. Thanks, Mike N8XPQ - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Help-tp18287766p18292637.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Help
My K3 is stuck in MCU LD mode. I have tried everything in reference to the com port settings. The K3 utility continues to say K3 not communicating. I have the latest version of the utility and have attempted to re-load 2.10 firmware as well as 2.13 with no luck. I have also tried forcing a firmware load per the manual and directions in the firmware help files. Still no luck. Any ideas? I really don't want to be with a dead rig all weekend. Thanks, Mike N8XPQ - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Help-tp18287766p18287766.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Help
I have noticed something new as well. When I click on the command tester tab, the window pops up and a strange y with 2 dots over top of it are rapidly scrolling across the screen and filling it up.H very strange? When I disconnect the serial cable from the rig, it stops. Mike Mike N8XPQ wrote: My K3 is stuck in MCU LD mode. I have tried everything in reference to the com port settings. The K3 utility continues to say K3 not communicating. I have the latest version of the utility and have attempted to re-load 2.10 firmware as well as 2.13 with no luck. I have also tried forcing a firmware load per the manual and directions in the firmware help files. Still no luck. Any ideas? I really don't want to be with a dead rig all weekend. Thanks, Mike N8XPQ - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Help-tp18287766p18288055.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Lightness of the K3
They are called push buttons not punch buttons. Go easy young jedi I have yet had the problem of the rig moving on the desk while in use. Lee Buller wrote: What are you doing to solve this problem The K3 is so lightwhen I push a button I move the K3 back. What are you doing to solve that issue? I am thinking of putting a stop behind the rig of some sort. Anyone dealt with this minor inconvenience? lee - K0WA In our day and age it seems that Common Sense is in short supply. If you don't have any Common Sense - get some Common Sense and use it. If you can't find any Common Sense, ask for help from somebody who has some Common Sense. Is Common Sense divine? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Lightness-of-the-K3-tp18195891p18197379.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Possible 2.02 FW glitch
- Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-2.02-FW-glitch-tp18060243p18060243.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Possible 2.02 FW glitch
Ok we will try this again, While on 160 meters if the VFO B knob is touched, the rig jumps uo to 75 meters. Has anyone else noticed this or can you duplicate it? Mike N8XPQ Mike N8XPQ wrote: - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-2.02-FW-glitch-tp18060243p18060272.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Possible 2.02 FW glitch
Yes it is on the K3. I have tested it in all modes and it occurs in all of them. I am not sure if it is related to a certain function I have enabled or not. I will keep digging into it. Let me know if you need further info. Mike Bud Semon N7CW wrote: Mike, I assume you mean for the K3. We probably need more info, but on a simple test, mine does not do that. 73, Bud N7CW -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mike N8XPQ Sent: Sunday, June 22, 2008 4:09 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible 2.02 FW glitch Ok we will try this again, While on 160 meters if the VFO B knob is touched, the rig jumps uo to 75 meters. Has anyone else noticed this or can you duplicate it? Mike N8XPQ Mike N8XPQ wrote: - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-2.02-FW-glitch-tp18060243p18060272.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-2.02-FW-glitch-tp18060243p18060460.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Possible K3 2.02 firmware bug
Has anyone else noticed that when in CW mode and in RX, if you turn on your computer which is connected to the rig or disconnect the USB cable the rig will start sending da's continuously? My conditions are K3 firmware 2.02 Windows XP home edition and a USB/serial converter. This strange operation has been happening also when I wake my laptop from sleep mode. Mike N8XPQ K3 #248 - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-K3-2.02-firmware-bug-tp17877118p17877118.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Possible K3 2.02 firmware bug
HIn fact I do. I had not thought of that. That is a ver good point as I have recently changed that setting to include DTR. Thank you for your suggestion. Mike N8XPQ Dick Dievendorff wrote: Do you have CW keying turned on for the DTR line? Sometimes computers assert DTR on serial ports during initialization. Dick, K6KR -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mike N8XPQ Sent: Monday, June 16, 2008 7:57 PM To: elecraft@mailman.qth.net Subject: [Elecraft] Possible K3 2.02 firmware bug Has anyone else noticed that when in CW mode and in RX, if you turn on your computer which is connected to the rig or disconnect the USB cable the rig will start sending da's continuously? My conditions are K3 firmware 2.02 Windows XP home edition and a USB/serial converter. This strange operation has been happening also when I wake my laptop from sleep mode. Mike N8XPQ K3 #248 - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-K3-2.02-firmware-bug-tp17877118p17877118.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Possible-K3-2.02-firmware-bug-tp17877118p17877470.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] side tone level adjust
Bruce, While in CW mode, hold the MON knob for 1 second. This will display the monitor or side tone level. Twist the knob to your desired setting and send away. I hope this helps. Mike N8XPQ Bruce McLaughlin-2 wrote: I am still having trouble with the rather low audio level of the side tone and spot tone in the CW mode on my new K-3. The other day I received an e-mail from a list member who suggested that those levels could be adjusted by using a config menu entry which specifically controlled and adjusted the side tone level. Try as I might I have yet to locate that entry. That may be because I am not very good at finding such things for some unknown reason. I have now installed version 1.96b firmware. Does anybody know how I can adjust the audio level of both the side tone and spot tone? Eager ears are waiting to know. Bruce-W8FU ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/side-tone-level-adjust-tp17442229p17442801.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] MCU 1.96 Possible Issue
I have noticed that when using my computer headset plugged into the rear connections and SPKR + PH is set to NO, the RX audio into the headset has a hollow or tin cannish sound to it. However when the feature is turned to YES, the oddity goes away. Has anyone else noticed this? Mike N8XPQ - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/MCU-1.96-Possible-Issue-tp17303343p17303343.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] tune pwr
Yes, Hold down the menu key to enter the config menu. Rotate VFO B knob until you find TUN PWR set this setting to your desired tune power. I hope this helps. Mike N8XPQ Todd Ruby wrote: I have just put the K3 on the air for the first time after downloading all firmware upgrades. When I hold TUNE pwr is at 0 and rotating the PWR ctrl gets it to a desired output just fine. when i go to retune it is back at 0 watts and I have to rotate the PWR knob each time. What is the way to have the PWR be at least set to where it was previously? tnx in advance 73 de todd WB2ZAB ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/tune-pwr-tp17152193p17152559.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] VOX sensitivity problem with new firmware
I have just tried the VOX, and I have noticed it as well. I turned the VOX gain up to 100 and it did then in fact TX, but I too had to speak quite loudly to get it to hold. I very rarely use VOX, so it would have been quite some to most likely before I would have noticed that. I am sure this will be repaired soon. Not to worry, Mike N8XPQ KM0O wrote: Before this latest firmware release, I would have said that the K3's VOX is the smoothest and finest I've ever used. But now, even with the sensitivity at 100 (max), I cannot get it to hold in without speaking rather loudly. Has anyone else noticed this? The antivox setting has no effect. - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/VOX-sensitivity-problem-with-new-firmware-tp17070521p17070683.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] firmware help
Check to see if you have the updated USB to serial drivers, if in fact you are using this avenue. Also possibly try to re-load the firmware again or revert back to the last firmware that you had loaded into the rig. I loaded mine without issue last night using windows XP and a USB/serial converter. Good luck, Mike N8XPQ mark crossland wrote: Please help., I've just downloaded the latest firmware and now my receiver is without any signal on any band Mark N1rfb K3--427 Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/firmware-help-tp17045462p17045946.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Firmware Update
The latest update is great, however I am curious as to when some of the more basic functions such as squelch, keypad beep, and ESSB TX will be enabled. I have also noticed that after the update, I can only listen out 4 KHz wide versus the prior 6 KHz with the AM filter installed. Also why not allow RX/TX passband down to 50 or so Hz? My intent is not to poke a sleeping bear, just curious. Also has anyone heard a whisper as to the availability of the DVR by field day? - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Firmware-Update-tp17046385p17046385.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 firmware update
Anyone have any idea how far out we are on the next badly needed firmware update? - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-firmware-update-tp16992743p16992743.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 1.78 Firmware Power Output
Has anyone noticed the power output with the 1.78 version does not seem to be a punchy or responsive? It seems to be very sluggish. I have attempted all parameter possibilities and still have had no luck. I am certain that with the previous versions, the output was much more responsive and was not like this. Unfortunately, it doesn't appear possible to revert back to a prior version. - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-1.78-Firmware-Power-Output-tp16376546p16376546.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 1.78 Firmware Power Output
Mike . . . You need to pay more attention to the reflector. This has been noted ad nauseum and will be corrected in the 1.79 which is due out shortly. K9ZTV (REPLY OFF-LINE) WOW...I guess I have been truly told I wasn't aware there were appointed frequency and reflector cops!! :-) Mike N8XPQ wrote: Has anyone noticed the power output with the 1.78 version does not seem to be a punchy or responsive? It seems to be very sluggish. I have attempted all parameter possibilities and still have had no luck. I am certain that with the previous versions, the output was much more responsive and was not like this. Unfortunately, it doesn't appear possible to revert back to a prior version. - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-1.78-Firmware-Power-Output-tp16376546p16376864.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] New Contest Transceiver
Nice looking rig, Howeverit still only has 1 receiver. Elecraft stated they will eventually have a pan adaptor/bandscope option for the K3. If you've read the recent test results, the K3 meets and sometimes, beats the 7700's big brother. And to add insult to injury, I dare venture that one could purchase 2 fully loaded K3's for the sticker shock price of the new kid on the block. Prove me wrong W7is wrote: If your interested in seeing the latest offering of a contest grade transceiver, take a look at this link. Reading their brochure is a real hoot!! During the next 10 days it will be making its official debut. http://www.icomamerica.com/en/downloads/Default.aspx?Category=180 **It's Tax Time! Get tips, forms, and advice on AOL Money Finance. (http://money.aol.com/tax?NCID=aolprf000301) ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/New-Contest-Transceiver-tp16115409p16121962.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Direct Frequency Entry
It seems that it is not possible to enter a frequency past the second decimal point. Ex: 7.047.50 The way it appears that when you get to the 7.047 entry the rig will beep at you, and not allow any further or more precise frequency entry. Am I missing an easy function or was this an oversight? - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Direct-Frequency-Entry-tp16055604p16055604.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Test message
Test message - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/Test-message-tp15794872p15794872.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Squelch Function
Am I missing something? I can not seem to enable the squelch function in the menu. The setting shows SQ Main --. It seems that I am unable to change this feature. Has anyone else discovered this? - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Squelch-Function-tp15787455p15787455.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Squelch Function
Well that clears it up and makes sense too. I thought I was going crazy! Thanks for the clarification and quick response. Mike N8XPQ Joe Stofko-2 wrote: Hi Mike, You wrote: Am I missing something? I can not seem to enable the squelch function in the menu. snip Nope, you are not missing anything. The squelch feature is not yet enabled in firmware. I do not know if it will be an all-mode squelch, but I expect it will not be available, at all, until FM is enabled. 73, Joe - W1AIU ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com - Mike Koetje N8XPQ -- View this message in context: http://www.nabble.com/K3-Squelch-Function-tp15795085p15797034.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com