[Elecraft] P3 hole cover
Hi all Can someone confirm that early orders for the P3 are being sent the P3 hole cover for the unused oulets on the rear cover as an upgrade? I also seem to remember a post about the I.F upgarde with the 13k resistor was being sent as well to very early K3 owners, mine being K3 #139. Any info on either appreciated. Oh and while I have your attention a reminder that I posted a video to Youtube showing my P3 during the ANZA Net, see : http://www.youtube.com/watch?v=aiUUO1pzM0k Cheers for now and vry 73 to all Peter ZL1PWD K3#139 P3#33 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] P3 #33 ANZA Net on Youtube
Hi all This is my first effort at uploading to youtube.com. Try: http://www.youtube.com/watch?v=aiUUO1pzM0k It will probably be my last as well until I get a faster connection :( 2+ hours to upload about 100Mb file!!! Anyway it is about 90seconds worth of the ANZA DX Net checkin session with KI6KFB (Kentucky Fried Bannanas) as net control Notice the width and strength of the Chinese OTHR signal which was still there at 07.00z. vry 73 Peter ZL1PWD K3#139 P3#33 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] P3 #33
Hi all P3 #33 arrived today after a week in Customs at Auckland Airport and payment of the requisite dues:( Anyway it all went together after about 2 hours A few issues: 1/ The bottom cover is quite a tight fit against the RJ connector and I may take it apart and adjust it with a small file. 2/ I will have to check if I have the I.F. Buffer Gain Mod. installed as the signals on screen are only visible on very strong ones. 3/ There is a blemish (photo available) on the front panel metal work in the cutout around the screen about 7-8mm up from the bottom on the right hand side.Its like there was a fault in the press that was used to make the cutout. 4/ I notice a red light flashing at about 50-60 hz from the underside thru a join in the steel panels. Any thoughts? vry 73 Peter ZL1PWD K3 #139 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Elecraft at Dayton
Can we have regular updates from attendees as to what is new,whats upgraded etc and all the scuttlebut!!! P3 delivery would also be good as would updates on the KPA 500!! Enjoy Dayton vry 73 Peter ZL1PWD K3#139 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Lineout level
Hi all, Here is an update to my line out problem in which there is no detectable line out signal. I have tested for a signal using headphones connected to the lineout socket and have no output.(Thanks Rich VE3KI) The K3AFMDKT upgade has been made with no improvement or difference in signal. To sumamrise: K3 with 13 khz filter at #1 pos and 2.7 at #2 KRX3 with 2.7 khz filter at # 1 pos KDVR also installed I can confirm that the lineout level was FB before the latest hardware upgrades. Any and all help very much appreciated. Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Lineout level
Hi all, Is there any way of measuring the line output level as I seem to have none that I can see? The reason I ask is I cannot seem to see any signals in the MixW waterfall anymore after upgarding to the 2nd RX and the DVR Full setup is 13.kzh filter in #1 and 2.7 in #2 with just the 2.7 in the second rx Yes i have the latest Elecraft Utility prog and F/W. I have obviously missed something in the config menu and any help appreciated BTW the rig was working FB before the upgrade to the second rx etc. I do have th K3AFMDKT kit at hand so wiil do that if I really have to Any help via the list [digest] or direct (peterdatigrindotcodotnz) tnx vry much Peter ZL1PWD K3#139___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 and MixW audio input volume
Seasons greetings from ZL, I have just upgraded to the 2nd RX and DVR and now get very little signal showing on the MixW waterfall. Not sure if there is a connection Using the latest FW and Menu item MIC SEL = LINE IN Config Item LIN OUT=3 Any thoughts?? TIA and 73 Peter ZL1PWD K3#139___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2-No tx on ssb
Hi all, I have had a query from a friend Bob ZL1VJ who has no tx on ssb in his K2. It has rx on ssb and works fb on cw,both tx and rx. This set was purchased from Ron ZL1TW not long before he became SK so our usual guru in ZL in not available and any advice appreciated. vry 73 Peter ZL1PWD K3 #139 K2 #4092___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] mail-archive.com/elecraft
Is the mail-archive server down or has my link gone bad? It's just that I notice the last listing is dated May 25 0!! 73 Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Major foobar!!
Hi all, I seem to have made a bit of a blue in installing the latest upgrade to the FW 1.88 and need some help! Have not been able to get much output on either PSK31 or SSB since upgrading the FW and would like to do a complete reset and start again, which I know is a PITA.. It WILL be operator error I am sure so just need some insight as to where to go from here. Any info appreciated vry 73 Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3/10 mojo - discovered the source.
Never mind Julian, I am sure there is counselling available under the NHS :) :) Peter Zl1PWD K3#139 G4ILO wrote: Gary Krause wrote: I run 5 to 10 watts on my K2 all the time. So have I for the last 9 years. And my K3 for the last 4 months. But with the current state of the ionosphere it's just too hard going, if you don't have an antenna farm like the ones in the photos. I feel like a traitor but my order has just gone in for the PA upgrade to my K3. -- View this message in context: http://www.nabble.com/K3-10-mojo---discovered-the-source.-tp16980794p16993170.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 memories
Am I missing something or is it buried somewhere how to save memory channels including the power setting;perhaps also filter settings as I have not taken note of that? It does gets a bit tiresome adjusting power settings when changing between SSB and the digi modes where I like to limit my power to about 20 watts. I agree with other posters who have commented on being able to load memories via the com port and with different configurations loaded it would be possible to have unlimited memories over all portions of the HF spectrum. Just a couple of thoughts from ZL 73 Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Ron ZL1TW-SK Funeral Details
UPDATE Funeral Details : Morris and Morris Funeral Directors 199 Kamo Road Whangarei Thursday 1.30 pm 7th February (NZDT) Any messages and cards should be sent to: Willcocks family 35 Puriri St, Kamo Whangarei 0112 NEW ZEALAND Peter ZL1PWD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] ZL1TW (SK)
Hi all, It is with a very heavy heart that I must inform the list that Ron ZL1TW passed away this morning ZL time after a short illness. He was my mentor, the ZL Elecraft guru, great family friend and all round great guy. I shall miss him deeply as will all his family and ham friends here and overseas. Will keep you posted re funeral arrangements etc. Peter ZL1PWD dit dit ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 #395/MM
Hi all, I have just worked WA6CDR/MM 7080 on MV/Braveheart which is on it's way to VP6 Ducie Is. Rob said I was the second K3 he had worked this evening, he was using #395 Cheers and 73 Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 question
Hi Stan, I can confirm the k3 cabinet color is All Black as in the New Zealand rugby football team!! Cheers for now and take care Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 question
That's a bit low Simon!! Cheers for now Peter ZL1PWD K3#139 It sure is a great radio - Original Message - From: Simon Brown (HB9DRV) [EMAIL PROTECTED] To: Peter ZL1PWD [EMAIL PROTECTED]; elecraft@mailman.qth.net Sent: Tuesday, January 08, 2008 9:28 PM Subject: Re: [Elecraft] K3 question - Original Message - From: Peter ZL1PWD [EMAIL PROTECTED] I can confirm the k3 cabinet color is All Black as in the New Zealand rugby football team!! The K3 is, however, a better performer :-) Simon HB9DRV -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.5.516 / Virus Database: 269.17.13/1213 - Release Date: 1/7/2008 9:14 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Re: K3 and MixW (Update)
I am pleased to report the problem is solved Many thanks to Greg AB7R (do you guys ever sleep??) Here is his reply: Pete, What mode do you have the K3 in. PSK-D? If so please change it. PSK-D is not ready just yet (see the errata sheet). PSK work great right now in Data-A mode with MixW. Make sure you use the MENU option MIC SEL and choose Line In. In this setup CMP is locked at zero (you need the current FW from the website). And MIC will control the output level. As you can see it was again a very simple solution.. Many thanks and a Happy New Year to all. Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 and MixW
Hi all and Happy New Year Can someone please show me where I am going wrong trying to get the the K3 in data mode to play nice nice with MixW? I can key the tx no problem but monitoring on my k2 shows about 4 vertical lines and it sounds like a carrier only and there is none of the usual twin vertical lines only of a clean PSK31 signal. The K3 decodes on the lcd readout but I cannot seem to get it to tx any intelligence thru a pc BTW I have connected the K3 to an Audigy2 soundcard per: K3 out===SC Mic In K3 inSC Line Out Any and all help appreciated and acknowledged. vry 73 and HNY Peter ZL1PWD K3#139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] How to clear your K3 through New Zealand Customs
Hi Phil, I am pleased to report that I had no problems at all getting my K3 /100 kit thru NZ Customs. I got a letter in the post, rang the enclosed phone# to pay NZ$381 GST etc and had it on my desk at the saltmine the next morning. The hardest part was looking at it all day at work!!. It went together a treat and works well. Be VERY carefull to completely read and understand the construction manual as I had a problem setting up and callibrating the rig but after a cople of emails to the helpful folk at Aptos all is well. Enjoy the rig and give us shout if you need help or want a K3 to K3 qso!! Cheers for now and HNY Peter ZL1PWD K3#139 Phil Holliday wrote: I was delighted to receive my K3 s/n 138 here in the Land of the Long White Cloud recently. Here are some notes for anyone else in ZL who is waiting for their shipment to clear NZ Customs. 'snip' Phil, zl3pah ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com -- View this message in context: http://www.nabble.com/How-to-clear-your-K3-through-New-Zealand-Customs-tp14511217p14517620.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Re: K3 139
Good afternoon/evening fromZL We have assembled the k3 and run the initial test stages and have run into a problem. During the lowpower wattmeter calibration we appear to have no TX output. Test indicate no RX either. Yes we have upgraded to the latest firmware, 01.49 Any suggestions??? Peter ZL1PWD K3 #0139 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] The word!
Hi all, I have just had the word of the coming dispatch of my K3 in7 to 10 days PTL and all that; YEESS I may have a project over the holiday season!! BTW it was ordered May 2 Cheers for now and 73 Peter ZL1PWD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com