[Elecraft] Trouble with Alignment and Test, Part II - - - MORE INFO
I decided to continuity with the alignment and testing, per the instructions. The BFO test and alignment went fine. But the next step - VFO Linearization, produced the following INFO message when I started the procedure: Info 232. The troubleshooting section says that the message "...is most likely to be displayed if you use CAL PLL without first selecing 40 meters." I am, of course, selecting 40 meters. So it looks like it is not recognizing the fact that 40 meters is selected. I have been going over the RF board, looking for soldering problems, but have found none. What is there that has 40m, 30m and 15m in common - that all would produce bad readings on the VCO Alignment? I have included my original post below. Again, thanks if you can help me. Mike, NJ2OM I ran into a little snag here and if anyone could help, I'd appreciate it. I have ser# 4619, just started the Alignment and Test, Part II. I In the VCO Alignment steps, I obtained the following results (Table 6-1. VCO Voltage Readings): BandLow Freq.VoltageHigh Freq.Voltage 80m 3500 2.04000 6.0 40m 7000.03 7300.03 30m1.03 10150.03 20m14000 2.3 15000 3.89 17m18000 2.99 18200 3.18 15m21000.03 21450.03 12m24800 3.84 25000 4.21 10m28000 3.16 28800 3.97 As you can see, the readings for 40m, 30m and 15m were not within range (1.5v - 7.5v). I checked all components (L30, D21-D26, and C71-C74 and the correct values were installed). T5 has the correct number of turns. I tried adjusting L30, per the instructions to move all the readings upwards, but adjusting L30 had no effect on the voltage reading for the affected bands. Just to repeat that, I adjusted L30 while watching the voltage readings, and it did not change the readings on the 3 affected bands. It did change the readings on all the other bands. If anyone can help, many thanks! Mike, NJ2OM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Trouble with Alignment and Test, Part II - - - MORE INFO
Mike wrote: Info 232. The troubleshooting section says that the message "...is most likely to be displayed if you use CAL PLL without first selecing 40 meters." I am, of course, selecting 40 meters. So it looks like it is not recognizing the fact that 40 meters is selected. Another common cause of this is not having the probe in the correct test point. -- 73, Vic, K2VCO Fresno CA http://www.qsl.net/k2vco ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Trouble with Alignment and Test, Part II - - - MORE INFO
Vic, thanks for the reply. Just rechecked it and that's not the cause. It was in TP1, per the instructions. - Original Message - From: "Vic Rosenthal" <[EMAIL PROTECTED]> To: "Mike" <[EMAIL PROTECTED]> Cc: "Elecraft" Sent: Sunday, January 02, 2005 1:41 PM Subject: Re: [Elecraft] Trouble with Alignment and Test, Part II - - - MORE INFO > Mike wrote: > > > Info 232. The troubleshooting section says that the message "...is most > > likely to be displayed if you use CAL PLL without first selecing 40 meters." > > I am, of course, selecting 40 meters. So it looks like it is not recognizing > > the fact that 40 meters is selected. > > Another common cause of this is not having the probe in the correct test point. > > -- > 73, > Vic, K2VCO > Fresno CA > http://www.qsl.net/k2vco > > ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
FW: [Elecraft] Trouble with Alignment and Test, Part II - - - MORE INFO
It says to linearize with the rig on 40 meters. What it doesn't say is that 40 meters needs to be working. As your VCO voltage reading on 40 meters is broke, so will be the linearization. You've got to get the VCO working first, I imagine. Dan / WG4S / K2 #2456 BandLow Freq.VoltageHigh Freq.Voltage 80m 3500 2.04000 6.0 40m 7000.03 7300.03 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
