[Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and FPU 1.4(?) and now today I notice that my SSB output is down about 3 dB. I can only coax about 50 Watts peak out of it and I've made no changes to microphone, TX EQ, Mic Gain, Compression, or output power (set to 100 W). CONFIG:TXG VCE is set to 1.0 dB as before. On CW I get a full 100 Watts peak. Anyone else seeing this? 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Power fine here with 4.17. Get full 100W PEP out on both CW and SSB and the drive power that I normally use for my amp is as accurate as it always was. Checked two K3s with an Alpha 4510, an LP-100A and an Array Solutions PowerMaster. I don't see anything different at all regarding power calibration (what it should be putting out versus what it atually is) or PEP out on two K3s and checked with three different meters. Greg K2UM __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Additional testing shows that when I set my power down to 5 Watts and then back up to 100 Watts results in a max peak output of 50 Watts on SSB on both an external and the K3's Wattmeter. Setting the mode to CW results in 100 Watts output and reverting back to SSB I can get about 75 Watts peak on both meters. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Nate, have you tried reloading the firmware? I'd give that a shot first. If that doesn't help, revert to the previous version and test again. In my case, latest beta firmware installed with no issues to report. 73 de James K2QI --Original Message-- From: Nate Bargmann Sender: elecraft-boun...@mailman.qth.net To: Elecraft Reflector Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? Sent: Nov 4, 2010 13:32 Additional testing shows that when I set my power down to 5 Watts and then back up to 100 Watts results in a max peak output of 50 Watts on SSB on both an external and the K3's Wattmeter. Setting the mode to CW results in 100 Watts output and reverting back to SSB I can get about 75 Watts peak on both meters. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Sent via BlackBerry from T-Mobile __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
In a word, yes Jim, W4ATK On Nov 4, 2010, at 12:18 PM, Nate Bargmann wrote: > I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and > FPU > 1.4(?) and now today I notice that my SSB output is down about 3 > dB. I > can only coax about 50 Watts peak out of it and I've made no changes > to > microphone, TX EQ, Mic Gain, Compression, or output power (set to > 100 W). > CONFIG:TXG VCE is set to 1.0 dB as before. > > On CW I get a full 100 Watts peak. > > Anyone else seeing this? > > 73, de Nate >> > > -- > > "The optimist proclaims that we live in the best of all > possible worlds. The pessimist fears this is true." > > Ham radio, Linux, bikes, and more: http://n0nb.us/index.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html JIM ROGERS w4...@bellsouth.net http://web.me.com/jimrogers_w4atk __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I went through the CONFIG menus to see what might have changed while in SSB. I found DUAL PB had APF on. I was unable to turn it off while in SSB, so went back to CW mode turned the APF off (nor) and returned to SSB and all was normal. Full output. I have confirmed you can only turn APF on/off while in CW mode. It would then seem that APF should be turned off automatically when in any mode other than CW. JIM ROGERS jimrogers_w4...@me.com http://web.me.com/jimrogers_w4atk JIM ROGERS w4...@bellsouth.net http://web.me.com/jimrogers_w4atk __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I'm new to all this. I noticed a lower output last night as well, after the ...17 load. Should we do a calibration and configuration after a FW update? Time to get out the SG2 again? ...bc BTW: the APF looks real cool. I'm not a CW operator, but this makes me drool a little bit. ..nr4c Quoting JAMES ROGERS : > In a word, yes > > > Jim, W4ATK > > On Nov 4, 2010, at 12:18 PM, Nate Bargmann wrote: > >> I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and >> FPU >> 1.4(?) and now today I notice that my SSB output is down about 3 >> dB. I >> can only coax about 50 Watts peak out of it and I've made no changes >> to >> microphone, TX EQ, Mic Gain, Compression, or output power (set to >> 100 W). >> CONFIG:TXG VCE is set to 1.0 dB as before. >> >> On CW I get a full 100 Watts peak. >> >> Anyone else seeing this? >> >> 73, de Nate >> >> >> -- >> >> "The optimist proclaims that we live in the best of all >> possible worlds. The pessimist fears this is true." >> >> Ham radio, Linux, bikes, and more: http://n0nb.us/index.html >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > JIM ROGERS > w4...@bellsouth.net > http://web.me.com/jimrogers_w4atk > > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I don't have any lack of ssb power output here after the new download with APF enabled in config. IO have to say I think the new APF is very good indeed. Running 4.17 on the K3 and 00.41 on the P3. 73 Stephen G4SJP On 04/11/2010 18:56, "n...@widomaker.com" wrote: > > I'm new to all this. I noticed a lower output last night as well, > after the ...17 load. Should we do a calibration and configuration > after a FW update? Time to get out the SG2 again? > > ...bc > > BTW: the APF looks real cool. I'm not a CW operator, but this makes > me drool a little bit. > > > ..nr4c > Quoting JAMES ROGERS : > >> In a word, yes >> >> >> Jim, W4ATK >> >> On Nov 4, 2010, at 12:18 PM, Nate Bargmann wrote: >> >>> I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and >>> FPU >>> 1.4(?) and now today I notice that my SSB output is down about 3 >>> dB. I >>> can only coax about 50 Watts peak out of it and I've made no changes >>> to >>> microphone, TX EQ, Mic Gain, Compression, or output power (set to >>> 100 W). >>> CONFIG:TXG VCE is set to 1.0 dB as before. >>> >>> On CW I get a full 100 Watts peak. >>> >>> Anyone else seeing this? >>> >>> 73, de Nate >> >>> >>> -- >>> >>> "The optimist proclaims that we live in the best of all >>> possible worlds. The pessimist fears this is true." >>> >>> Ham radio, Linux, bikes, and more: http://n0nb.us/index.html >>> __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >> >> JIM ROGERS >> w4...@bellsouth.net >> http://web.me.com/jimrogers_w4atk >> >> >> >> >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
* On 2010 04 Nov 14:06 -0500, Stephen Prior wrote: > I don't have any lack of ssb power output here after the new download with > APF enabled in config. Interesting. Thanks to Jim for finding that setting Dual PB to Nor will correct this. Hopefully, Wayne is reading this thread. :-) > IO have to say I think the new APF is very good indeed. Running 4.17 on the > K3 and 00.41 on the P3. I agree. I think it's a worthwhile addition even with this small bug. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I am unable to duplicate your conditions, I am only able to get APF on in CW mode. Wonder if this would be something where a previously uncontrolled memory bit is in an undetermined state, leaving a strange "remembered" condition when those bits are used for the first time? 73, Guy. On Thu, Nov 4, 2010 at 2:50 PM, JAMES ROGERS wrote: > I went through the CONFIG menus to see what might have changed while > in SSB. I found DUAL PB had APF on. I was unable to turn it off while > in SSB, so went back to CW mode turned the APF off (nor) and returned > to SSB and all was normal. Full output. > > I have confirmed you can only turn APF on/off while in CW mode. > It would then seem that APF should be turned off automatically when in > any mode other than CW. > > JIM ROGERS > jimrogers_w4...@me.com > http://web.me.com/jimrogers_w4atk > > > > JIM ROGERS > w4...@bellsouth.net > http://web.me.com/jimrogers_w4atk > > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I had no loss of SSB power output after the 4.17 Beta install. The APF works wonderfully, with only a hint of ringing to my ears. Really nice addition to the K3. --Dave, W8OV On 11/4/2010 3:11 PM, Nate Bargmann wrote: > * On 2010 04 Nov 14:06 -0500, Stephen Prior wrote: >> I don't have any lack of ssb power output here after the new download with >> APF enabled in config. > Interesting. Thanks to Jim for finding that setting Dual PB to Nor will > correct this. Hopefully, Wayne is reading this thread. :-) > >> IO have to say I think the new APF is very good indeed. Running 4.17 on the >> K3 and 00.41 on the P3. > I agree. I think it's a worthwhile addition even with this small bug. > > 73, de Nate>> > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: > I had no loss of SSB power output after the 4.17 Beta install. The APF > works wonderfully, with only a hint of ringing to my ears. Really nice > addition to the K3. At least some of you aren't seeing this. :-) James Rogers suggested turning the Mic gain to 0 and then back up and he was getting good output. After I did that, I could only get about 25 Watts peak on both meters. I switched to CW mode, transmitted a short carrier which showed 100 Watts on both meters (power control set to 100). Switching back to SSB both meters showed about 70 Watts. I have since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts peak on each meter (I say four in a normal voice to get the K3's meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 dB. I'm not sure that rolling back to the last stable firmware would solve this or be fraught with other issues. Generally, roll-backs don't work all that well in other devices. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Please retry TX gain calibration on affected bands. This is the usual cure for a difference between CW and SSB power output. Wayne N6KR http://www.elecraft.com On Nov 4, 2010, at 4:30 PM, Nate Bargmann wrote: > * On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >> I had no loss of SSB power output after the 4.17 Beta install. The >> APF >> works wonderfully, with only a hint of ringing to my ears. Really >> nice >> addition to the K3. > > At least some of you aren't seeing this. :-) > > James Rogers suggested turning the Mic gain to 0 and then back up > and he > was getting good output. After I did that, I could only get about 25 > Watts peak on both meters. I switched to CW mode, transmitted a short > carrier which showed 100 Watts on both meters (power control set to > 100). Switching back to SSB both meters showed about 70 Watts. I > have > since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 > Watts > peak on each meter (I say four in a normal voice to get the K3's > meter to stabilize for a bit). I had previously had TXG VCE set to > 1.0 > dB. > > I'm not sure that rolling back to the last stable firmware would solve > this or be fraught with other issues. Generally, roll-backs don't > work > all that well in other devices. > > 73, de Nate >> > > -- > > "The optimist proclaims that we live in the best of all > possible worlds. The pessimist fears this is true." > > Ham radio, Linux, bikes, and more: http://n0nb.us/index.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Well, rolling back is worth a shot. I've never had problems reverting to previous versions. Plus, look at it this way - what variables have changed? If this issue manifested itself after the last fw update, then that should be a good place to start. James K2QI Sent via BlackBerry from T-Mobile -Original Message- From: Nate Bargmann Sender: elecraft-boun...@mailman.qth.net Date: Thu, 4 Nov 2010 18:30:44 To: Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? * On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: > I had no loss of SSB power output after the 4.17 Beta install. The APF > works wonderfully, with only a hint of ringing to my ears. Really nice > addition to the K3. At least some of you aren't seeing this. :-) James Rogers suggested turning the Mic gain to 0 and then back up and he was getting good output. After I did that, I could only get about 25 Watts peak on both meters. I switched to CW mode, transmitted a short carrier which showed 100 Watts on both meters (power control set to 100). Switching back to SSB both meters showed about 70 Watts. I have since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts peak on each meter (I say four in a normal voice to get the K3's meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 dB. I'm not sure that rolling back to the last stable firmware would solve this or be fraught with other issues. Generally, roll-backs don't work all that well in other devices. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I am seeing the same reduction in SSB output power. I installed 4.17 Beta last night. It appears that the reduced power only occurs when I have APF activated. I have twice restored SSB power by doing the following: 1). Changing mode back to CW, 2). Going to Dual PB in Config menu and turning APF off, 3). exiting Config menu, 4). changing mode back to SSB. Power is restored back to a full 100 watts. With APF set to on, SSB power is reduced to about 70 watts. I confirmed this on 17M by repeating the process twice, and I then tried 20 M SSB and the power was back to 70 watts (after I had turned APF back on.) Is this a problem with the beta release? I saw Wayne's suggestion to do a TX gain calibration, but it seems strange that I would only need to do this after installing Beta 4.17. APF works great, but I need to resolve this SSB power issue. I may try RTTY next to see what happens in that mode. Dave, N4QS - Original Message - From: "Nate Bargmann" To: Sent: Thursday, November 04, 2010 6:30 PM Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? >* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >> I had no loss of SSB power output after the 4.17 Beta install. The APF >> works wonderfully, with only a hint of ringing to my ears. Really nice >> addition to the K3. > > At least some of you aren't seeing this. :-) > > James Rogers suggested turning the Mic gain to 0 and then back up and he > was getting good output. After I did that, I could only get about 25 > Watts peak on both meters. I switched to CW mode, transmitted a short > carrier which showed 100 Watts on both meters (power control set to > 100). Switching back to SSB both meters showed about 70 Watts. I have > since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts > peak on each meter (I say four in a normal voice to get the K3's > meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 > dB. > > I'm not sure that rolling back to the last stable firmware would solve > this or be fraught with other issues. Generally, roll-backs don't work > all that well in other devices. > > 73, de Nate >> > > -- > > "The optimist proclaims that we live in the best of all > possible worlds. The pessimist fears this is true." > > Ham radio, Linux, bikes, and more: http://n0nb.us/index.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Hi Dave, In CW mode, in CONFIG:PB CTRL, what value is in SHIFT= ?? Thanks, Guy. On Thu, Nov 4, 2010 at 8:34 PM, Dave Perry N4QS wrote: > I am seeing the same reduction in SSB output power. I installed 4.17 Beta > last night. It appears that the reduced power only occurs when I have APF > activated. I have twice restored SSB power by doing the following: 1). > Changing mode back to CW, 2). Going to Dual PB in Config menu and turning > APF off, 3). exiting Config menu, 4). changing mode back to SSB. Power is > restored back to a full 100 watts. With APF set to on, SSB power is reduced > to about 70 watts. I confirmed this on 17M by repeating the process twice, > and I then tried 20 M SSB and the power was back to 70 watts (after I had > turned APF back on.) Is this a problem with the beta release? I saw > Wayne's suggestion to do a TX gain calibration, but it seems strange that I > would only need to do this after installing Beta 4.17. > > APF works great, but I need to resolve this SSB power issue. I may try RTTY > next to see what happens in that mode. > > Dave, N4QS > > > - Original Message - > From: "Nate Bargmann" > To: > Sent: Thursday, November 04, 2010 6:30 PM > Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? > > >>* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >>> I had no loss of SSB power output after the 4.17 Beta install. The APF >>> works wonderfully, with only a hint of ringing to my ears. Really nice >>> addition to the K3. >> >> At least some of you aren't seeing this. :-) >> >> James Rogers suggested turning the Mic gain to 0 and then back up and he >> was getting good output. After I did that, I could only get about 25 >> Watts peak on both meters. I switched to CW mode, transmitted a short >> carrier which showed 100 Watts on both meters (power control set to >> 100). Switching back to SSB both meters showed about 70 Watts. I have >> since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts >> peak on each meter (I say four in a normal voice to get the K3's >> meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 >> dB. >> >> I'm not sure that rolling back to the last stable firmware would solve >> this or be fraught with other issues. Generally, roll-backs don't work >> all that well in other devices. >> >> 73, de Nate >> >> >> -- >> >> "The optimist proclaims that we live in the best of all >> possible worlds. The pessimist fears this is true." >> >> Ham radio, Linux, bikes, and more: http://n0nb.us/index.html >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Now I seem to have a real problem. I did a TX Gain calibration using the K3 Utility for both 5 and 50 watts. I worked perfectly and tx gain appeared to be right on all bands. I then did some testing into a dummy load with RTTY. I noticed that power would start out at 25 watts and it would take several transmissions to get it up to 70 to 100 watts. So I decided to do a wattmeter calibration. I had selected WMTR LP and was attempting to do the 5.0 W calibration into a dummy load. But I could not get the output power to change much and after several tries I got a high current reading. Now I can get audio only out of the left side of headphones and when I attempt to reselect the WTMR parameter it is no longer there. The selection in Config skips from VFO OFS to XVn ON. I assume I have blown something out. However, I am considering reverting back to MCU version 4.14. Any other suggestions? Thanks in advance. I would hate to see the K3 go down right before the SS CW weekend. Dave, N4QS - Original Message - From: "Dave Perry N4QS" To: "Nate Bargmann" ; Sent: Thursday, November 04, 2010 7:34 PM Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? >I am seeing the same reduction in SSB output power. I installed 4.17 Beta > last night. It appears that the reduced power only occurs when I have APF > activated. I have twice restored SSB power by doing the following: 1). > Changing mode back to CW, 2). Going to Dual PB in Config menu and turning > APF off, 3). exiting Config menu, 4). changing mode back to SSB. Power is > restored back to a full 100 watts. With APF set to on, SSB power is > reduced > to about 70 watts. I confirmed this on 17M by repeating the process > twice, > and I then tried 20 M SSB and the power was back to 70 watts (after I had > turned APF back on.) Is this a problem with the beta release? I saw > Wayne's suggestion to do a TX gain calibration, but it seems strange that > I > would only need to do this after installing Beta 4.17. > > APF works great, but I need to resolve this SSB power issue. I may try > RTTY > next to see what happens in that mode. > > Dave, N4QS > > > - Original Message - > From: "Nate Bargmann" > To: > Sent: Thursday, November 04, 2010 6:30 PM > Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? > > >>* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >>> I had no loss of SSB power output after the 4.17 Beta install. The APF >>> works wonderfully, with only a hint of ringing to my ears. Really nice >>> addition to the K3. >> >> At least some of you aren't seeing this. :-) >> >> James Rogers suggested turning the Mic gain to 0 and then back up and he >> was getting good output. After I did that, I could only get about 25 >> Watts peak on both meters. I switched to CW mode, transmitted a short >> carrier which showed 100 Watts on both meters (power control set to >> 100). Switching back to SSB both meters showed about 70 Watts. I have >> since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts >> peak on each meter (I say four in a normal voice to get the K3's >> meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 >> dB. >> >> I'm not sure that rolling back to the last stable firmware would solve >> this or be fraught with other issues. Generally, roll-backs don't work >> all that well in other devices. >> >> 73, de Nate >> >> >> -- >> >> "The optimist proclaims that we live in the best of all >> possible worlds. The pessimist fears this is true." >> >> Ham radio, Linux, bikes, and more: http://n0nb.us/index.html >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
OK, my SSB output was low too. I'm on phone so rarely, were it not for the reflector, I'd probably never have checked and when I did find out, the thread would have already died. I did the TX Gain calibration as Wayne suggested, all seems to be well on all bands. Apparently, the DL in my MFJ tuner isn't all that 50 ohms-ish on 6m, but the trusty Heath Cantenna is. The APF feature is really quite amazing. I have to miss SS CW, family stuff, but I'm anxious to try it out for real. It already got me 9U0A, he was whisper weak, maybe S[minus]1, I got "9A" and wondered why the pileup on a 9A? APF in, he sounded S5. S-meter was still on the peg however. 73, Fred K6DGW - Northern California Contest Club - CU in the 2011 Cal QSO Party 1-2 Oct 2011 - www.cqp.org On 11/4/2010 10:32 AM, Nate Bargmann wrote: > Additional testing shows that when I set my power down to 5 Watts and > then back up to 100 Watts results in a max peak output of 50 Watts on > SSB on both an external and the K3's Wattmeter. Setting the mode to CW > results in 100 Watts output and reverting back to SSB I can get about 75 > Watts peak on both meters. > > 73, de Nate>> > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Guy, I solved the audio problem. Speakers had somehow been set to 1. Turned it back to 2. But WMTR parameter is totally missing. So I guess I will try reverting back to 4.14. Dave - Original Message - From: "Guy Olinger K2AV" To: "Dave Perry N4QS" Sent: Thursday, November 04, 2010 9:16 PM Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? This is so completely wierd On Thu, Nov 4, 2010 at 10:07 PM, Dave Perry N4QS wrote: > Now I seem to have a real problem. I did a TX Gain calibration using the > K3 > Utility for both 5 and 50 watts. I worked perfectly and tx gain appeared > to > be right on all bands. I then did some testing into a dummy load with > RTTY. > I noticed that power would start out at 25 watts and it would take several > transmissions to get it up to 70 to 100 watts. So I decided to do a > wattmeter calibration. I had selected WMTR LP and was attempting to do the > 5.0 W calibration into a dummy load. But I could not get the output power > to change much and after several tries I got a high current reading. Now I > can get audio only out of the left side of headphones and when I attempt > to > reselect the WTMR parameter it is no longer there. The selection in Config > skips from VFO OFS to XVn ON. I assume I have blown something out. > However, I am considering reverting back to MCU version 4.14. Any other > suggestions? > > Thanks in advance. I would hate to see the K3 go down right before the SS > CW weekend. > > Dave, N4QS > > - Original Message - > From: "Dave Perry N4QS" > To: "Nate Bargmann" ; > Sent: Thursday, November 04, 2010 7:34 PM > Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? > > >>I am seeing the same reduction in SSB output power. I installed 4.17 Beta >> last night. It appears that the reduced power only occurs when I have APF >> activated. I have twice restored SSB power by doing the following: 1). >> Changing mode back to CW, 2). Going to Dual PB in Config menu and turning >> APF off, 3). exiting Config menu, 4). changing mode back to SSB. Power is >> restored back to a full 100 watts. With APF set to on, SSB power is >> reduced >> to about 70 watts. I confirmed this on 17M by repeating the process >> twice, >> and I then tried 20 M SSB and the power was back to 70 watts (after I had >> turned APF back on.) Is this a problem with the beta release? I saw >> Wayne's suggestion to do a TX gain calibration, but it seems strange that >> I >> would only need to do this after installing Beta 4.17. >> >> APF works great, but I need to resolve this SSB power issue. I may try >> RTTY >> next to see what happens in that mode. >> >> Dave, N4QS >> >> >> - Original Message - >> From: "Nate Bargmann" >> To: >> Sent: Thursday, November 04, 2010 6:30 PM >> Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? >> >> >>>* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >>>> I had no loss of SSB power output after the 4.17 Beta install. The APF >>>> works wonderfully, with only a hint of ringing to my ears. Really nice >>>> addition to the K3. >>> >>> At least some of you aren't seeing this. :-) >>> >>> James Rogers suggested turning the Mic gain to 0 and then back up and he >>> was getting good output. After I did that, I could only get about 25 >>> Watts peak on both meters. I switched to CW mode, transmitted a short >>> carrier which showed 100 Watts on both meters (power control set to >>> 100). Switching back to SSB both meters showed about 70 Watts. I have >>> since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts >>> peak on each meter (I say four in a normal voice to get the K3's >>> meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 >>> dB. >>> >>> I'm not sure that rolling back to the last stable firmware would solve >>> this or be fraught with other issues. Generally, roll-backs don't work >>> all that well in other devices. >>> >>> 73, de Nate >> >>> >>> -- >>> >>> "The optimist proclaims that we live in the best of all >>> possible worlds. The pessimist fears this is true." >>> >>> Ham radio, Linux, bikes, and more: http://n0nb.us/index.html >>> __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> He
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
* On 2010 04 Nov 21:10 -0500, Dave Perry N4QS wrote: > Now I seem to have a real problem. I did a TX Gain calibration using the K3 > Utility for both 5 and 50 watts. I worked perfectly and tx gain appeared to > be right on all bands. I then did some testing into a dummy load with RTTY. > I noticed that power would start out at 25 watts and it would take several > transmissions to get it up to 70 to 100 watts. This is precisely what I had been seeing, Dave. On lyle's suggestion I rolled the MCU back to 4.14 and the FPF to 1.13 and left the DSP at 2.65. The SSB ouput power persisted so I rolled the DSP back to 2.60 and SSB power is back to normal matching CW power again. The improvement was immediate. > Thanks in advance. I would hate to see the K3 go down right before the SS > CW weekend. Sorry to hear of your issues. At Wayne's suggestion I had done the TX Gain calibration on the beta firmware with no change in behavior. I will, however, bump back up to the beta before SS. Now that I know what's going on I can work with it. 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Same thing to me, I was noticed it when put my Amp w/GU84B on, need 20w+ to obtain 500w in ssb instead of my normal 16w. MH2 Mic dynamics was also affected and obliged to increase the Mic gain consequently. When back to NOR Dual PB features it comes back almost to normal power but seems a bit lack of dynamic. When download back the 4.14, everything returns to "normal". I have download again the 4.17 and same "problem" occurs but let it like this the time a solution will be available on line. Anyway the APF is really impressive to extract the weak signal and really enjoyed it. It is also a must to catch the beacons qrg's. Bst 73s Philippe A65BI >>> "Dave Perry N4QS" 05-11-2010 4:34 >>> I am seeing the same reduction in SSB output power. I installed 4.17 Beta last night. It appears that the reduced power only occurs when I have APF activated. I have twice restored SSB power by doing the following: 1). Changing mode back to CW, 2). Going to Dual PB in Config menu and turning APF off, 3). exiting Config menu, 4). changing mode back to SSB. Power is restored back to a full 100 watts. With APF set to on, SSB power is reduced to about 70 watts. I confirmed this on 17M by repeating the process twice, and I then tried 20 M SSB and the power was back to 70 watts (after I had turned APF back on.) Is this a problem with the beta release? I saw Wayne's suggestion to do a TX gain calibration, but it seems strange that I would only need to do this after installing Beta 4.17. APF works great, but I need to resolve this SSB power issue. I may try RTTY next to see what happens in that mode. Dave, N4QS - Original Message - From: "Nate Bargmann" To: Sent: Thursday, November 04, 2010 6:30 PM Subject: Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? >* On 2010 04 Nov 18:23 -0500, Dave, W8OV wrote: >> I had no loss of SSB power output after the 4.17 Beta install. The APF >> works wonderfully, with only a hint of ringing to my ears. Really nice >> addition to the K3. > > At least some of you aren't seeing this. :-) > > James Rogers suggested turning the Mic gain to 0 and then back up and he > was getting good output. After I did that, I could only get about 25 > Watts peak on both meters. I switched to CW mode, transmitted a short > carrier which showed 100 Watts on both meters (power control set to > 100). Switching back to SSB both meters showed about 70 Watts. I have > since bumped TXG VCE up to the max, 3.0 dB and am getting about 90 Watts > peak on each meter (I say four in a normal voice to get the K3's > meter to stabilize for a bit). I had previously had TXG VCE set to 1.0 > dB. > > I'm not sure that rolling back to the last stable firmware would solve > this or be fraught with other issues. Generally, roll-backs don't work > all that well in other devices. > > 73, de Nate >> > > -- > > "The optimist proclaims that we live in the best of all > possible worlds. The pessimist fears this is true." > > Ham radio, Linux, bikes, and more: http://n0nb.us/index.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
We're working on the SSB problem. 73, Wayne N6KR On Nov 4, 2010, at 9:49 PM, Philippe Trottet wrote: > Same thing to me, I was noticed it when put my Amp w/GU84B on, need > 20w+ to obtain 500w in ssb instead of my normal 16w... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
I have the same experience that Philippe has. I thought I had one or both 3cx800A7 tubes going flat in my amp when I had to increase the drive to a level I never have been close to approaching to get 1KW out. It's great to hear that you guys are on this new glitch so quickly. Tim On Thu, Nov 4, 2010 at 9:54 PM, Wayne Burdick wrote: > We're working on the SSB problem. > > 73, > Wayne > N6KR > > On Nov 4, 2010, at 9:49 PM, Philippe Trottet wrote: > > > Same thing to me, I was noticed it when put my Amp w/GU84B on, need > > 20w+ to obtain 500w in ssb instead of my normal 16w... > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
After many tries, on Dummy load first then with distant Ham friends, conclusion was to re-installed MCU 4.14. Instead of giving the same dynamic with the MH2 microphone, with my Amp on, using 12w drive, using Mic=2 COMP=20, pronouncing the number 6 slowly, I have seen immediately the difference. For me, using a Amp w/GU84B tetrode, 12w drive on ssb give 500~600w on normal voice operation. With MCU 4.17 it gave only 300~400w and the power increase with difficulty on a single whistle to 500w. and when I pushed to maxi drive 65~70w I was unable to achieve the normal 64dBm+ of the Amp with normal voice. Normal cw tune procedure seems not affected and I can achieve the maxi as normal. The most important: It has been reported to me during the test on the air, some alteration of the modulation, like a RFI ground phenomena on the microphone or like a under voltage problem during transmitting. I've checked all connections from A to Z and no problem founded. re-load 4.17, installed it 2 times, with no changes. When re-installing the MCU 4.14 everything is back to normal with the very clear voice provided by the K3. Sure Wayne will share with us what's happened, .APF is a so great add-up in weak signal environment ! Bst 73's Philippe A65BI >>> Tim Tucker 05-11-2010 20:02 >>> I have the same experience that Philippe has. I thought I had one or both 3cx800A7 tubes going flat in my amp when I had to increase the drive to a level I never have been close to approaching to get 1KW out. It's great to hear that you guys are on this new glitch so quickly. Tim On Thu, Nov 4, 2010 at 9:54 PM, Wayne Burdick wrote: > We're working on the SSB problem. > > 73, > Wayne > N6KR > > On Nov 4, 2010, at 9:49 PM, Philippe Trottet wrote: > > > Same thing to me, I was noticed it when put my Amp w/GU84B on, need > > 20w+ to obtain 500w in ssb instead of my normal 16w... > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Same thing..with 4.17 beta my SSB output dropped to 50W...reverted back to 4.14 everything is ok. APF was great though ;) Olli OH6CT -Alkuperäinen viesti- Lähettäjä: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] Puolesta Nate Bargmann Lähetetty: 4. marraskuuta 2010 19:19 Vastaanottaja: Elecraft list Aihe: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output? I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and FPU 1.4(?) and now today I notice that my SSB output is down about 3 dB. I can only coax about 50 Watts peak out of it and I've made no changes to microphone, TX EQ, Mic Gain, Compression, or output power (set to 100 W). CONFIG:TXG VCE is set to 1.0 dB as before. On CW I get a full 100 Watts peak. Anyone else seeing this? 73, de Nate >> -- "The optimist proclaims that we live in the best of all possible worlds. The pessimist fears this is true." Ham radio, Linux, bikes, and more: http://n0nb.us/index.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
We're working on the SSB issue. Wayne On Nov 5, 2010, at 10:51 AM, Olli Tuppurainen wrote: > Same thing..with 4.17 beta my SSB output dropped to 50W...reverted > back to > 4.14 everything is ok. > APF was great though ;) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Phillippe, You state the mic gain setting and the compression, but for the K3, the most important setting is to obtain 5 to 7 bars on the ALC meter with the compression turned to zero. If that is not done as the first step, then the K3 cannot properly control its power output. After setting the mic gain level for those 5 to 7 bars, then increase the compression to whatever you want. You may want to recheck to be sure your mic gain is set correctly (even though an SSB bug apparently came along with 4.17. BTW, thank you for trying the beta firmware - it is good to give Elecraft feedback on problems like this one. While I am not saying this is your problem, we need frequent reminders of this initial requirement because many instructions for amplifiers and for digital interface boxes (use 4 to 5 bars for digital) will lead you to believe that you should control power output with the mic gain setting. While that is true for many transceivers, it is not good advice for the K3. From the many posts on the reflector, there was a problem for SSB power output (bug) that happened in MCU 4.17, and Wayne has said he is working on it. 73, Don W3FPR On 11/5/2010 1:45 PM, Philippe Trottet wrote: > After many tries, on Dummy load first then with distant Ham friends, > conclusion was to re-installed MCU 4.14. > Instead of giving the same dynamic with the MH2 microphone, with my Amp on, > using 12w drive, using Mic=2 COMP=20, pronouncing the number 6 slowly, I have > seen immediately the difference. > For me, using a Amp w/GU84B tetrode, 12w drive on ssb give 500~600w on normal > voice operation. > With MCU 4.17 it gave only 300~400w and the power increase with difficulty on > a single whistle to 500w. and when I pushed to maxi drive 65~70w I was unable > to achieve the normal 64dBm+ of the Amp with normal voice. > Normal cw tune procedure seems not affected and I can achieve the maxi as > normal. > > The most important: > It has been reported to me during the test on the air, some alteration of the > modulation, like a RFI ground phenomena on the microphone or like a under > voltage problem during transmitting. > I've checked all connections from A to Z and no problem founded. re-load > 4.17, installed it 2 times, with no changes. > When re-installing the MCU 4.14 everything is back to normal with the very > clear voice provided by the K3. > Sure Wayne will share with us what's happened, .APF is a so great add-up in > weak signal environment ! > Bst 73's > Philippe A65BI > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Nate et all, I stand corrected. Looks like K3 #2730 also has this issue. I didn't notice at first, but then noticed it last night. Performing a TX calibration didn't really fix it completely, although it did help. Glad to know that the boys at Aptos are working on it. 73 de James K2QI On Thu, Nov 4, 2010 at 2:02 PM, wrote: > Nate, have you tried reloading the firmware? I'd give that a shot first. If > that doesn't help, revert to the previous version and test again. > > In my case, latest beta firmware installed with no issues to report. > > 73 de James K2QI > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Successfully downloaded MCU4.17 and began experimenting with APV. It took awhile to find a weak CW signal - 20m band must be in good shape. I did find one that was pretty spotty reception in 2.8-KHz bw; a bit better with 400-Hz. Then is turned on the APV. I could see a definite improvement once I got familiar with how to use it; signal went S=0 to S=2. That is a nice enhancement in the firmware. I will be doing primarily weak-signal CW with my K3 on 144-MHz and 1296-MHz eme. The 400-Hz filter takes some getting use to compared with 400-Hz DSP bw on my FT-847 (i.e. there is NO comparison). The 8-pole K3 xtal filter just "chops off" everything outside the narrow band. Background noise drops significantly, too. I may want to do my eme search in 2.8, then narrow bw once I find a signal to copy. Fortunately, Ihave sw can detect a carrier way below audio threshold (down to SNR= - 28 dB in a 2.8-KHz band). I tested my SSB Tx levels using TUNE and the mic (on 20m) and they indicate normal RF output so not seeing any issue on my K3/10 (16w max output) (#4030). I did play with CONFIG: PB CTRL 0.05 or 0.01; the 0.01 seemed to work with APV nicer. --- Sidenote: My new 1296/28 transverter was shipped on Wed. Just confirmed that I will be receiving a prototype dual-RX transverter for 144/28 MHz. Steve at Downeast Microwwave is using me as beta-tester for this new model. I will run it with my dual-polarity 2m antenna array to capture polarity-angle information using Linrad sw. This will utilize the dual-Rx in my K3. I guess you could say this will make my eme station a polarity diversity receiver. Early details: http://www.kl7uw.com/eme144.htm 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 144-800*w, 432-100w, 1296-QRT*, 3400-winter? DUBUS Magazine USA Rep dubus...@hotmail.com == *temp not in service __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
We've now fixed this and are re-testing the code. Should have a new beta release later this evening. Wayne __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 MCU 4.17 (APF beta) kills SSB output?
Hi Wayne, Just downloaded MCU 4.18. Great improvement and everything is ok now. Once again many thanks for the tremendous support of the Elecraft team. Bst 73's Philippe A65BI Elecraft, by Hams, for HamsWhat else ! >>> Wayne Burdick 05-11-2010 8:54 >>> We're working on the SSB problem. 73, Wayne N6KR On Nov 4, 2010, at 9:49 PM, Philippe Trottet wrote: > Same thing to me, I was noticed it when put my Amp w/GU84B on, need > 20w+ to obtain 500w in ssb instead of my normal 16w... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html