Re: [Elecraft] Elecraft K4 and Accessibility
I note that Harry went from Elecraft to Japanese radios, Flex and Anan. I presume he means the Flex M radios and the newly released Mk 2 Anan which do have knobs while the predecessors do not. I thought about my recent usage of my K3. After pressing the power button, I set the output power to drive my alpha amp, and while operating adjusted the audio level control and infrequently the audio passband filter, turned on XIT 20 Hz low when pouncing or used RIT when running, rarely touched high and low cut, and used the VFO. Using N1MM I am able to tune the radio, change bands, adjust the keyer speed, clear the RIT and toggle it on and off, and even spot tune a CW signal. I like the organization of the knobs and buttons that it does have. Those that are dual function do not confuse me at all. I do not find the buttons too small and they are definitely not too cluttered. I operate portable a lot in the summer. The compact size and light weight are a plus. I am older than Rick T. You commented about the 6700’s place on the Sherwood tables. Yes, it is in second place for 2 KHz offset dynamic range, but not for 20 KHz offset. Oh, did you read footnote “y” ? Watsonville, I am ready to play K4 music. Bob R – N7WY __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
K4 should succeed in that it appears to build upon K3/P3/KRX3 (highly successful) with added color screen, direct-sampling SDR, and increased I/O. The same K3 "upgradeable approach" applies to K4. If you are not into contesting then K4 SDR may be all you wish (especially if you already have a K3 for contesting). You do have to pay for the upgradeable approach even if you are not interested in upgrading. This is the advantage of Elecraft IMHO. I purchased my first k3 in 2008, and it is as good in 2019 as my K3s. An upgradeable radio also helps with radio repair cost, in addition to NOT purchasing a new model radio just to obtain improved performance. Before I ended up with K3/P3 so2r in 2015, I went through a new board to improve K3 audio, the replacement of the pins affecting the KPA3 module, and new synthesizers (plus a few minor mods). My K3 eventually replaced ft1000mp, Omni VI, and (finally) Orion. I'm satisfied using K3 so2r more so than at any point in the past. Based on my past experience I suspect K4 has a bright future! 73, Will, wj9b PS: This is not the same as saying that I do not like other radios. I still have Orion and a broken Omni VI that I hope to repair. CWops #1085 CWA Advisor levels II and II,: http://cwops.org On Sun, 5/26/19, Rick Tavan wrote: Subject: Re: [Elecraft] Elecraft K4 and Accessibility To: hwhi...@maine.rr.com Cc: "Elecraft Reflector" , k...@yahoogroups.com, elecraft...@groups.io Date: Sunday, May 26, 2019, 12:55 PM Wow. Your preference seems to be in a minority, Harry, although I have to admit that my opinion is subjective and based mainly on what I've read on this reflector which may well be biased by folks like me who *like* the K3. I think Elecraft retained in the K4 many of the design points that made the K3 very successful and enduring, including its light weight and small size which are two major complaints on your list. So it may be a chocolate vs. vanilla situation - some people (like me) value those characteristics while other people (like you) dislike them. Of course, you're right that many prospective buyers are aging and some may come to dislike smaller knobs, I for one still find the knobs and buttons plenty big enough and I'm now 70 years old. I once measured the K3 button size and spacing against my prior favorite rig, the FT-1000MP, and found them practically the same. I never had trouble operating the K3 and its menu structure was logical, rarely needed, and self-documenting. The new K4 screen is plenty large enough for me and comparable to many current, competitive radios'. It can also be blown up to as large as you like through the addition of an in expensive, external, HDMI monitor or a tablet. I've seen it and it was gorgeous. So you're certainly correct that some people like big, heavy radios with "substantial" knobs and they may not buy the K4. Others like radios they can lift without back strain, carry to vacation homes and field sites, operate remotely with minimal external hardware, and expect to survive through upgrades for a decade. Many of them, like me, have been K3 fans for 12 years or so and will be delighted to buy the K4. The market will decide. I think the K4 will be highly successful and I'm rooting for it. We'll see. 73, /Rick N6XI -- Rick Tavan Truckee, CA On Fri, May 24, 2019 at 5:00 PM wrote: > Wayne and interested others, > > Way back when, I bought a loaded K3. I believe the S/N was around 4K? It > was back in the day when almost every DXpedition was using K3's so it was > obviously the radio to own. (Around 2009?) It was at the top of the > Sherwood ratings. Owner's bragged, incessantly, about its Sherwood rating. > > After a period of time I grew to really dislike that radio. The audio was > just plain awful and the man/machine interface was the worst I have ever > seen. I detest bar graphs. I suppose if you play at ham radio 8 hours a > day, seven days a week, the interface is "normal", even usable. For those > of us who might get on the air for an hour or two a week, the controls were > a mystery. Tap this button to do this, hold the same button for three > seconds to do that, the list goes on. NOTHING was intuitive. It did not > help that it was an incredibly ugly, too light and unsubstantial, radio. > It's looks may have been barely acceptable when first introduced but it > aged badly, rapidly. Over a ten year period it's price has become a real > problem. > > There were many, many questions on this reflector regarding the controls, > the same questions about the same controls, over and over and over again. > That should have been a very large hint that the controls should be > massively improved in any new r
Re: [Elecraft] Elecraft K4 and Accessibility
Jim, I feel like a newbie. Only 56 years for me. But I agree. When I haul the K3 to KP2M the only knobs I use when I am on frequency are the AF gain and RIT for those who are off frequency. N2TK, Tony -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Jim Brown Sent: Sunday, May 26, 2019 2:29 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] Elecraft K4 and Accessibility On 5/24/2019 5:00 PM, hwhi...@maine.rr.com wrote: > I suggest you double the size of the radio and change your design criteria. This is exactly the opposite of how I feel about radios -- I'll be 78 in the fall, but I'm still an active guy dragging my gear to portable setups, and my shack is a SO2R contesting setup (single op, two radios). For both reasons, I am VERY happy with the light weight and small footprint of the K3 (as well as it's predecessor, the K2, and relatives, the KX3 and KX2). I don't want big knobs or even a lot of knobs -- when I'm operating, the only knobs I'm using are the gain controls and whatever changes frequency, including RIT or XIT. But what do I know -- I've only been doing it for 63 years. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
would not be a huge cost driver. Remember who your customers are. And when the Flex 6700 kicked the K3 out of first place in the Sherwood ratings in 2014, the Koolaid drinkers on this reflector were heard to say, "People put too much faith in numbers". Hypocrisy is thy name. I haven't stopped laughing. This email pertains to only the second and third paragraphs of Wayne's reply below. I wish Elecraft well with the K4 but I really think your minimalist/too complex way of designing needs to change. You've probably already guessed that I won't be a customer of the K4 as currently proposed. And you really, really ought to improve this reflector... 73, Harry K1RSA -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Wayne Burdick Sent: Friday, May 24, 2019 2:03 PM To: Elecraft Reflector ; k...@yahoogroups.com; elecraft...@groups.io Subject: [Elecraft] Elecraft K4 and Accessibility Hi Buddy et al, We've definitely been thinking about this. There's a paradigm shift going on in transceiver design, and we reached a point where we needed to embrace it. This shift is not entirely aligned with accessibility, as you know. I'll address alternatives in this email. As for the K4 specifically, its user interface is dependent in part on use of the touch screen. This was simply the only way to integrate an equivalent of the K3S, P3, and all of the new hardware/software required to implement a direct-sampling radio. The use of a touch screen allows context sensitivity (physical overloading) for controls, making the K4 the equivalent of a much larger radio without touch. The resulting compact size is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a hallmark of Elecraft transceivers. Regarding accessibility, there are three possible approaches: 1. The K4's entire complement of controls, both hard and touch, will be represented by a set of "2-letter" commands. This API will be fully public as it is for our other transceivers. Presumably external devices or computers will be able to immediately make use of these commands to effect a flexible accessible interface. 2. In theory we could implement a large-target version of the LCD's touch controls, with proximity-based audio feedback and no panadapter. This would be a very ambitious project requiring ongoing support, similar to that needed for mobile/fixed app development. We don't have the staff to support this, so we'd need to engage the wider community to find a developer with suitable skills and motivation. The API or spec for such an effort doesn't exist at this time. 3. The K3S has very similar strong-signal performance and similar basic features, without touch. Since many of the added features of the K4 are panadapter-centric, a blind ham may very well find that the K3S is a viable alternative. No doubt there will be more used K3's and K3S's on the market over the next year. The KX3 and KX2 provide audio CW feedback on most controls and are another non-touch alternative. I hope the alternatives I've suggested to use of the K4's normal UI will be helpful in most cases. 73, Wayne N6KR On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] < kx3-nore...@yahoogroups.com> wrote: [Sorry, sent this to Gary instead of the list] Hey Gary, I’m curious about this as well, as are others…see K8HSY’s post on the blind-hams list. See also my response full of speculation (below). Wayne, please feel free to comment on my comments and correct me where I erred: I’ve been beating the accessibility drum on the Elecraft reflector for ages, and Wayne has assured that they would not go to all touch screen access, for that very reason. Elecraft has, in the person of one of their tech support people in the past, and Wayne in emails to me, committed to doing what they can in design parameters to make accessibility attainable, and they have been super cooperative with people like the Hampod folks and others who want to design accessibility tools. The K4 has a full GNU/Linux computer built into it, and it’s got a client/server architecture, with network access available, so it seems to me accessibility should be possible, even relatively easy, to implement. Especially given that there are still a wide range of physical buttons and knobs on board. And, unlike Yaecomwoodlincotec, the principals at Elecraft are not only available by email, but very responsive besides. If you’re really interested in a perspective direct from the horse’s mouth, write to Wayne directly at n...@elecraft.com. He really does answer email. Buddy Brannan, KB5ELV - Erie, PA Email: bu...@brannan.name Mobile: (814) 431-0962 On May 23, 2019, at 1:47 PM, Gary Lee kb9...@arrl.net [KX3] < kx3-nore...@yahoogroups.com> wrote: could someone describe the front panel of the k4 with reference to that of the k3? With the added touch screen, I am wondering about usability for
Re: [Elecraft] Elecraft K4 and Accessibility
On 5/26/2019 11:55 AM, Rick Tavan wrote: I never had trouble operating the K3 and its menu structure was logical, rarely needed, and self-documenting. The new K4 screen is plenty large enough for me and comparable to many current, competitive radios'. It can also be blown up to as large as you like through the addition of an in expensive, external, HDMI monitor or a tablet. I've seen it and it was gorgeous. In addition to being a very smart engineer, Rick is a great operator who has competed in several WRTCs. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
to only the second and third paragraphs of Wayne's > reply below. > > I wish Elecraft well with the K4 but I really think your minimalist/too > complex way of designing needs to change. You've probably already guessed > that I won't be a customer of the K4 as currently proposed. And you really, > really ought to improve this reflector... > > 73, > > Harry K1RSA > > -Original Message- > From: elecraft-boun...@mailman.qth.net > On Behalf Of Wayne Burdick > Sent: Friday, May 24, 2019 2:03 PM > To: Elecraft Reflector ; k...@yahoogroups.com; > elecraft...@groups.io > Subject: [Elecraft] Elecraft K4 and Accessibility > > Hi Buddy et al, > > We've definitely been thinking about this. > > There's a paradigm shift going on in transceiver design, and we reached a > point where we needed to embrace it. This shift is not entirely aligned > with accessibility, as you know. I'll address alternatives in this email. > > As for the K4 specifically, its user interface is dependent in part on use > of the touch screen. This was simply the only way to integrate an > equivalent of the K3S, P3, and all of the new hardware/software required to > implement a direct-sampling radio. The use of a touch screen allows context > sensitivity (physical overloading) for controls, making the K4 the > equivalent of a much larger radio without touch. The resulting compact size > is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and > power-efficient), a hallmark of Elecraft transceivers. > > Regarding accessibility, there are three possible approaches: > > 1. The K4's entire complement of controls, both hard and touch, will be > represented by a set of "2-letter" commands. This API will be fully public > as it is for our other transceivers. Presumably external devices or > computers will be able to immediately make use of these commands to effect > a flexible accessible interface. > > 2. In theory we could implement a large-target version of the LCD's touch > controls, with proximity-based audio feedback and no panadapter. This would > be a very ambitious project requiring ongoing support, similar to that > needed for mobile/fixed app development. We don't have the staff to support > this, so we'd need to engage the wider community to find a developer with > suitable skills and motivation. The API or spec for such an effort doesn't > exist at this time. > > 3. The K3S has very similar strong-signal performance and similar basic > features, without touch. Since many of the added features of the K4 are > panadapter-centric, a blind ham may very well find that the K3S is a viable > alternative. No doubt there will be more used K3's and K3S's on the market > over the next year. The KX3 and KX2 provide audio CW feedback on most > controls and are another non-touch alternative. > > I hope the alternatives I've suggested to use of the K4's normal UI will > be helpful in most cases. > > 73, > Wayne > N6KR > > > > > > On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] < > kx3-nore...@yahoogroups.com> wrote: > > > > [Sorry, sent this to Gary instead of the list] Hey Gary, > > > > I’m curious about this as well, as are others…see K8HSY’s post on the > blind-hams list. See also my response full of speculation (below). Wayne, > please feel free to comment on my comments and correct me where I erred: > > > > I’ve been beating the accessibility drum on the Elecraft reflector for > ages, and Wayne has assured that they would not go to all touch screen > access, for that very reason. Elecraft has, in the person of one of their > tech support people in the past, and Wayne in emails to me, committed to > doing what they can in design parameters to make accessibility attainable, > and they have been super cooperative with people like the Hampod folks and > others who want to design accessibility tools. > > > > The K4 has a full GNU/Linux computer built into it, and it’s got a > client/server architecture, with network access available, so it seems to > me accessibility should be possible, even relatively easy, to implement. > Especially given that there are still a wide range of physical buttons and > knobs on board. > > > > And, unlike Yaecomwoodlincotec, the principals at Elecraft are not only > available by email, but very responsive besides. If you’re really > interested in a perspective direct from the horse’s mouth, write to Wayne > directly at n...@elecraft.com. He really does answer email. > > > > Buddy Brannan, KB5ELV - Erie, PA > > Email: bu...@brannan.name > > Mobile: (814) 431-0962 > >
Re: [Elecraft] Elecraft K4 and Accessibility
> This email pertains to only the second and third paragraphs of Wayne's > reply below. > > I wish Elecraft well with the K4 but I really think your minimalist/too > complex way of designing needs to change. You've probably already guessed > that I won't be a customer of the K4 as currently proposed. And you really, > really ought to improve this reflector... > > 73, > > Harry K1RSA > > -Original Message- > From: elecraft-boun...@mailman.qth.net > On Behalf Of Wayne Burdick > Sent: Friday, May 24, 2019 2:03 PM > To: Elecraft Reflector ; k...@yahoogroups.com; > elecraft...@groups.io > Subject: [Elecraft] Elecraft K4 and Accessibility > > Hi Buddy et al, > > We've definitely been thinking about this. > > There's a paradigm shift going on in transceiver design, and we reached a > point where we needed to embrace it. This shift is not entirely aligned > with accessibility, as you know. I'll address alternatives in this email. > > As for the K4 specifically, its user interface is dependent in part on use > of the touch screen. This was simply the only way to integrate an > equivalent of the K3S, P3, and all of the new hardware/software required to > implement a direct-sampling radio. The use of a touch screen allows context > sensitivity (physical overloading) for controls, making the K4 the > equivalent of a much larger radio without touch. The resulting compact size > is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and > power-efficient), a hallmark of Elecraft transceivers. > > Regarding accessibility, there are three possible approaches: > > 1. The K4's entire complement of controls, both hard and touch, will be > represented by a set of "2-letter" commands. This API will be fully public > as it is for our other transceivers. Presumably external devices or > computers will be able to immediately make use of these commands to effect > a flexible accessible interface. > > 2. In theory we could implement a large-target version of the LCD's touch > controls, with proximity-based audio feedback and no panadapter. This would > be a very ambitious project requiring ongoing support, similar to that > needed for mobile/fixed app development. We don't have the staff to support > this, so we'd need to engage the wider community to find a developer with > suitable skills and motivation. The API or spec for such an effort doesn't > exist at this time. > > 3. The K3S has very similar strong-signal performance and similar basic > features, without touch. Since many of the added features of the K4 are > panadapter-centric, a blind ham may very well find that the K3S is a viable > alternative. No doubt there will be more used K3's and K3S's on the market > over the next year. The KX3 and KX2 provide audio CW feedback on most > controls and are another non-touch alternative. > > I hope the alternatives I've suggested to use of the K4's normal UI will > be helpful in most cases. > > 73, > Wayne > N6KR > > > > > > On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] < > kx3-nore...@yahoogroups.com> wrote: > > > > [Sorry, sent this to Gary instead of the list] Hey Gary, > > > > I’m curious about this as well, as are others…see K8HSY’s post on the > blind-hams list. See also my response full of speculation (below). Wayne, > please feel free to comment on my comments and correct me where I erred: > > > > I’ve been beating the accessibility drum on the Elecraft reflector for > ages, and Wayne has assured that they would not go to all touch screen > access, for that very reason. Elecraft has, in the person of one of their > tech support people in the past, and Wayne in emails to me, committed to > doing what they can in design parameters to make accessibility attainable, > and they have been super cooperative with people like the Hampod folks and > others who want to design accessibility tools. > > > > The K4 has a full GNU/Linux computer built into it, and it’s got a > client/server architecture, with network access available, so it seems to > me accessibility should be possible, even relatively easy, to implement. > Especially given that there are still a wide range of physical buttons and > knobs on board. > > > > And, unlike Yaecomwoodlincotec, the principals at Elecraft are not only > available by email, but very responsive besides. If you’re really > interested in a perspective direct from the horse’s mouth, write to Wayne > directly at n...@elecraft.com. He really does answer email. > > > > Buddy Brannan, KB5ELV - Erie, PA > > Email: bu...@brannan.name > > Mobile: (814) 431-0962 > >
Re: [Elecraft] Elecraft K4 and Accessibility
On 5/24/2019 5:00 PM, hwhi...@maine.rr.com wrote: I suggest you double the size of the radio and change your design criteria. This is exactly the opposite of how I feel about radios -- I'll be 78 in the fall, but I'm still an active guy dragging my gear to portable setups, and my shack is a SO2R contesting setup (single op, two radios). For both reasons, I am VERY happy with the light weight and small footprint of the K3 (as well as it's predecessor, the K2, and relatives, the KX3 and KX2). I don't want big knobs or even a lot of knobs -- when I'm operating, the only knobs I'm using are the gain controls and whatever changes frequency, including RIT or XIT. But what do I know -- I've only been doing it for 63 years. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
Good morning Wayne, That's a great idea; trying the K4. See you at Boxboro. Harry K1RSA -Original Message- From: Wayne Burdick Sent: Friday, May 24, 2019 8:21 PM To: hwhi...@maine.rr.com Cc: Elecraft Reflector ; k...@yahoogroups.com; elecraft...@groups.io Subject: Re: [Elecraft] Elecraft K4 and Accessibility > On May 24, 2019, at 5:00 PM, hwhi...@maine.rr.com wrote: > Last week the K4 was announced so I rejoined the reflector. ... From all that I have read, the controls will be even more complex. The K4's controls are actually quite a bit simpler, and more intuitive, thanks to the new display. We were limited to a small display with fixed segments in the K3/K3S, which constrained the ways we could provide visual feedback. Also, as the years went by, we added many new features that, in turn, were constrained by the existing switches/knobs/display. This evolution may not have been ideal from a UI standpoint, but it provided our customers with features they wanted, without the need to continually buy a new radio. We accepted a long time ago that we can't please everyone or satisfy every ergonomic requirement. Our business was forged at Field Day, so portability will remain a high priority. Lifting or carrying a K4 won't hurt aging backs. We (and hundreds who tried the radio at Dayton, expressing delight at the new front panel) feel that the K4's UI is not just a significant advance over the K3/K3S, but also over most other transceivers in its class, regardless of their size and weight. I invite you to try the radio in person if you get the chance. 73, Wayne N6KR --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
Harry, There is no one radio or mfg for all of us. An old FT101 will pretty much work anyone on the air. Your views, needs are interesting and your prentation measured. 73 Doug EI2CNSent from my Samsung Galaxy smartphone. Original message From: Edward R Cole Date: 25/05/2019 08:15 (GMT+00:00) To: Elecraft Reflector Subject: Re: [Elecraft] Elecraft K4 and Accessibility Harry, From what you wrote seems the K3/K4 probably is a poor fit for your ham radio experience. Short time, occasional use probably other radios would be easier since you probably don't need or would use many of the features of these radios.When I bought my K3 (sn4340) in 2010 it took me a few week to fully understand a lot of its features. But I thoroughly love the radio. I use the diversity Rx a lot for my eme operating. I likewise don't care for the sound of the built-in speaker so I either use and external speaker or headphones.I'd liken the K3 to something like a Porshe or Maserati. I would guess you probably prefer a comfortable Mercury or Impala. BTW on cars I chose a Ford pickup as appropriate to my use.73, Ed - KL7UW http://www.kl7uw.comDubus-NA Business mail: dubus...@gmail.com __Elecraft mailing listHome: http://mailman.qth.net/mailman/listinfo/elecraftHelp: http://mailman.qth.net/mmfaq.htmPost: mailto:elecr...@mailman.qth.netThis list hosted by: http://www.qsl.netPlease help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
Harry, From what you wrote seems the K3/K4 probably is a poor fit for your ham radio experience. Short time, occasional use probably other radios would be easier since you probably don't need or would use many of the features of these radios. When I bought my K3 (sn4340) in 2010 it took me a few week to fully understand a lot of its features. But I thoroughly love the radio. I use the diversity Rx a lot for my eme operating. I likewise don't care for the sound of the built-in speaker so I either use and external speaker or headphones. I'd liken the K3 to something like a Porshe or Maserati. I would guess you probably prefer a comfortable Mercury or Impala. BTW on cars I chose a Ford pickup as appropriate to my use. 73, Ed - KL7UW http://www.kl7uw.com Dubus-NA Business mail: dubus...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
Hi Wayne. I am expecting to buy a new radio next year so good discussion on the K4. I expect to use my current upgraded K3 both at home and in the field, perhaps at a field day event so high dynamic range is good. At home we are out in a rural area so the K4 or K4D will be good. I tend to not use tough screen things but if the touch screen was robust as I read is true for the K4 that might be fine. Comments below... On 5/24/2019 11:02 AM, Wayne Burdick wrote: Hi Buddy et al, We've definitely been thinking about this. There's a paradigm shift going on in transceiver design, and we reached a point where we needed to embrace it. This shift is not entirely aligned with accessibility, as you know. I'll address alternatives in this email. As for the K4 specifically, its user interface is dependent in part on use of the touch screen. This was simply the only way to integrate an equivalent of the K3S, P3, and all of the new hardware/software required to implement a direct-sampling radio. The use of a touch screen allows context sensitivity (physical overloading) for controls, making the K4 the equivalent of a much larger radio without touch. The resulting compact size is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a hallmark of Elecraft transceivers. Integrating the P3 is very nice. So having a hybrid touch and knob radio would actually work. Regarding accessibility, there are three possible approaches: 1. The K4's entire complement of controls, both hard and touch, will be represented by a set of "2-letter" commands. This API will be fully public as it is for our other transceivers. Presumably external devices or computers will be able to immediately make use of these commands to effect a flexible accessible interface. Either way this is good as I use digital modes programs, such as fldigi, JS8Call and WSJT-X sometimes. So regardless of #2 or #3 this is good. 2. In theory we could implement a large-target version of the LCD's touch controls, with proximity-based audio feedback and no panadapter. This would be a very ambitious project requiring ongoing support, similar to that needed for mobile/fixed app development. We don't have the staff to support this, so we'd need to engage the wider community to find a developer with suitable skills and motivation. The API or spec for such an effort doesn't exist at this time. Not something I want but for poor eyesight might be handy. 3. The K3S has very similar strong-signal performance and similar basic features, without touch. Since many of the added features of the K4 are panadapter-centric, a blind ham may very well find that the K3S is a viable alternative. No doubt there will be more used K3's and K3S's on the market over the next year. The KX3 and KX2 provide audio CW feedback on most controls and are another non-touch alternative. Well, keep the accessories for a K3 or K3S available and this might be fine. I am sighted but this is important. Thanks for the opportunity to comment. 73, tom w7sua I hope the alternatives I've suggested to use of the K4's normal UI will be helpful in most cases. 73, Wayne N6KR On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] wrote: [Sorry, sent this to Gary instead of the list] Hey Gary, I’m curious about this as well, as are others…see K8HSY’s post on the blind-hams list. See also my response full of speculation (below). Wayne, please feel free to comment on my comments and correct me where I erred: I’ve been beating the accessibility drum on the Elecraft reflector for ages, and Wayne has assured that they would not go to all touch screen access, for that very reason. Elecraft has, in the person of one of their tech support people in the past, and Wayne in emails to me, committed to doing what they can in design parameters to make accessibility attainable, and they have been super cooperative with people like the Hampod folks and others who want to design accessibility tools. The K4 has a full GNU/Linux computer built into it, and it’s got a client/server architecture, with network access available, so it seems to me accessibility should be possible, even relatively easy, to implement. Especially given that there are still a wide range of physical buttons and knobs on board. And, unlike Yaecomwoodlincotec, the principals at Elecraft are not only available by email, but very responsive besides. If you’re really interested in a perspective direct from the horse’s mouth, write to Wayne directly at n...@elecraft.com. He really does answer email. Buddy Brannan, KB5ELV - Erie, PA Email: bu...@brannan.name Mobile: (814) 431-0962 On May 23, 2019, at 1:47 PM, Gary Lee kb9...@arrl.net [KX3] wrote: could someone describe the front panel of the k4 with reference to that of the k3? With the added touch screen, I am wondering about usability for the blind operator.
Re: [Elecraft] Elecraft K4 and Accessibility
Rod, I doubt that the Elecraft Principals and Engineers are such delicate snowflakes that they are unable to deal with some frank feedback from any corner. And, in many ways, critical feedback inviting a review of basic design principles is at least as valuable as pages of Q about work-arounds and detail; it all has its place. Harsh criticism, respectfully delivered as Harry's was, is not trolling. I'm a happy KPA1500 owner but, as you recognize, not everyone warms to all products from a given manufacturer and, despite close examination of Elecraft transceiver offerings, I made alternative choices, most recently involving a TS-890S (which, by the way, also has the RIT/XIT in the right place!). I look forward to the K4 release and have no doubts it will be a great radio. I may yet vote in that direction but I found the way Elecraft handled the K4 announcement (controlled leak?) baffling and reminiscent of Apple and their fanboys. I recall a thread on the K4 being closed a couple of months ago, only for another sanctioned one to emerge and continue, followed by the dribble of actual news about the K4. It was all just odd, in my view. 73, Peter (VK6HP). -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Rod Hardman Sent: Saturday, 25 May 2019 8:17 AM To: hwhi...@maine.rr.com Cc: Elecraft Reflector ; k...@yahoogroups.com; elecraft...@groups.io Subject: Re: [Elecraft] Elecraft K4 and Accessibility Harry, you got they the first time. I respect your right to an opinion and right to vote with your dollars. You represent a market segment that Elecraft May or may not choose to address. It’s Wayne and Eric’s strategy to decide. I for one may represent a different (slightly) younger market segment and I have been drawn to the Elecraft UI and design philosophy. I create computer based products, although mostly software these days and I think Wayne and the development team are spot on. To me, the Elecraft menus just “feel right” compared to the Japanese approach. There’s lots of room for different market segments in this hobby. Everyone should vote with there dollars. Eric, Wayne and the whole team should be mindful of all feedback, but be respectful of their their choices (and others tastes). let’s not come on the Elecraft reflector to troll Elecraft design. It’s not cool to call someone’s kid ugly. I’m sure you were not intending to be hurtful, but I know too well engineers put their whole Hearts into such things and I’m always careful about that / rod, VA3ON On May 24, 2019, at 20:00, wrote: Wayne and interested others, Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was back in the day when almost every DXpedition was using K3's so it was obviously the radio to own. (Around 2009?) It was at the top of the Sherwood ratings. Owner's bragged, incessantly, about its Sherwood rating. After a period of time I grew to really dislike that radio. The audio was just plain awful and the man/machine interface was the worst I have ever seen. I detest bar graphs. I suppose if you play at ham radio 8 hours a day, seven days a week, the interface is "normal", even usable. For those of us who might get on the air for an hour or two a week, the controls were a mystery. Tap this button to do this, hold the same button for three seconds to do that, the list goes on. NOTHING was intuitive. It did not help that it was an incredibly ugly, too light and unsubstantial, radio. It's looks may have been barely acceptable when first introduced but it aged badly, rapidly. Over a ten year period it's price has become a real problem. There were many, many questions on this reflector regarding the controls, the same questions about the same controls, over and over and over again. That should have been a very large hint that the controls should be massively improved in any new radio. I sold my K3 and moved on to the big Japanese three, ANAN, and Flex, over the years. All had many, fairly easy to understand, controls. All were far, far more usable than the K3. Both the ANAN and Flex service departments are as good as Elecraft's. Eventually I left the Elecraft reflector, and that is a whole other story. Last week the K4 was announced so I rejoined the reflector. It sounded like a really great radio. Sadly, I have concluded it will be a dud, mostly because it is designed with the same philosophy as the K3 was, a small, compact, easily transportable radio, "a hallmark of Elecraft transceivers", to quote you, Wayne. From all that I have read, the controls will be even more complex. Ham radio operators are an aging group. Some suffer from the "fat finger" syndrome, others have vision problems, to name just two. The last thing they need or want is a tiny radio with minimal controls, each of which serves two or three or four or five purposes. They favor a radio that has many
Re: [Elecraft] Elecraft K4 and Accessibility
I’ll be interested in hearing what you think after you use a K4. Chuck Jack KE9UW Sent from my iPhone, cjack > On May 24, 2019, at 7:00 PM, "hwhi...@maine.rr.com" > wrote: > > Wayne and interested others, > > Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was > back in the day when almost every DXpedition was using K3's so it was > obviously the radio to own. (Around 2009?) It was at the top of the Sherwood > ratings. Owner's bragged, incessantly, about its Sherwood rating. > > After a period of time I grew to really dislike that radio. The audio was > just plain awful and the man/machine interface was the worst I have ever > seen. I detest bar graphs. I suppose if you play at ham radio 8 hours a day, > seven days a week, the interface is "normal", even usable. For those of us > who might get on the air for an hour or two a week, the controls were a > mystery. Tap this button to do this, hold the same button for three seconds > to do that, the list goes on. NOTHING was intuitive. It did not help that it > was an incredibly ugly, too light and unsubstantial, radio. It's looks may > have been barely acceptable when first introduced but it aged badly, rapidly. > Over a ten year period it's price has become a real problem. > > There were many, many questions on this reflector regarding the controls, the > same questions about the same controls, over and over and over again. That > should have been a very large hint that the controls should be massively > improved in any new radio. > > I sold my K3 and moved on to the big Japanese three, ANAN, and Flex, over the > years. All had many, fairly easy to understand, controls. All were far, far > more usable than the K3. Both the ANAN and Flex service departments are as > good as Elecraft's. > > Eventually I left the Elecraft reflector, and that is a whole other story. > > Last week the K4 was announced so I rejoined the reflector. It sounded like a > really great radio. Sadly, I have concluded it will be a dud, mostly because > it is designed with the same philosophy as the K3 was, a small, compact, > easily transportable radio, "a hallmark of Elecraft transceivers", to quote > you, Wayne. From all that I have read, the controls will be even more complex. > > Ham radio operators are an aging group. Some suffer from the "fat finger" > syndrome, others have vision problems, to name just two. The last thing they > need or want is a tiny radio with minimal controls, each of which serves two > or three or four or five purposes. They favor a radio that has many single or > dual purpose knobs. They want bigger screens, the K4 screens are too small. > > I suggest you double the size of the radio and change your design criteria. > Enlarging the physical size would not be a huge cost driver. Remember who > your customers are. > > And when the Flex 6700 kicked the K3 out of first place in the Sherwood > ratings in 2014, the Koolaid drinkers on this reflector were heard to say, > "People put too much faith in numbers". Hypocrisy is thy name. I haven't > stopped laughing. > > This email pertains to only the second and third paragraphs of Wayne's reply > below. > > I wish Elecraft well with the K4 but I really think your minimalist/too > complex way of designing needs to change. You've probably already guessed > that I won't be a customer of the K4 as currently proposed. And you really, > really ought to improve this reflector... > > 73, > > Harry K1RSA > > -Original Message- > From: elecraft-boun...@mailman.qth.net On > Behalf Of Wayne Burdick > Sent: Friday, May 24, 2019 2:03 PM > To: Elecraft Reflector ; k...@yahoogroups.com; > elecraft...@groups.io > Subject: [Elecraft] Elecraft K4 and Accessibility > > Hi Buddy et al, > > We've definitely been thinking about this. > > There's a paradigm shift going on in transceiver design, and we reached a > point where we needed to embrace it. This shift is not entirely aligned with > accessibility, as you know. I'll address alternatives in this email. > > As for the K4 specifically, its user interface is dependent in part on use of > the touch screen. This was simply the only way to integrate an equivalent of > the K3S, P3, and all of the new hardware/software required to implement a > direct-sampling radio. The use of a touch screen allows context sensitivity > (physical overloading) for controls, making the K4 the equivalent of a much > larger radio without touch. The resulting compact size is still compatible > with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient
Re: [Elecraft] Elecraft K4 and Accessibility
> On May 24, 2019, at 5:00 PM, hwhi...@maine.rr.com wrote: > Last week the K4 was announced so I rejoined the reflector. ... From all that > I have read, the controls will be even more complex. The K4's controls are actually quite a bit simpler, and more intuitive, thanks to the new display. We were limited to a small display with fixed segments in the K3/K3S, which constrained the ways we could provide visual feedback. Also, as the years went by, we added many new features that, in turn, were constrained by the existing switches/knobs/display. This evolution may not have been ideal from a UI standpoint, but it provided our customers with features they wanted, without the need to continually buy a new radio. We accepted a long time ago that we can't please everyone or satisfy every ergonomic requirement. Our business was forged at Field Day, so portability will remain a high priority. Lifting or carrying a K4 won't hurt aging backs. We (and hundreds who tried the radio at Dayton, expressing delight at the new front panel) feel that the K4's UI is not just a significant advance over the K3/K3S, but also over most other transceivers in its class, regardless of their size and weight. I invite you to try the radio in person if you get the chance. 73, Wayne N6KR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
Harry, you got they the first time. I respect your right to an opinion and right to vote with your dollars. You represent a market segment that Elecraft May or may not choose to address. It’s Wayne and Eric’s strategy to decide. I for one may represent a different (slightly) younger market segment and I have been drawn to the Elecraft UI and design philosophy. I create computer based products, although mostly software these days and I think Wayne and the development team are spot on. To me, the Elecraft menus just “feel right” compared to the Japanese approach. There’s lots of room for different market segments in this hobby. Everyone should vote with there dollars. Eric, Wayne and the whole team should be mindful of all feedback, but be respectful of their their choices (and others tastes). let’s not come on the Elecraft reflector to troll Elecraft design. It’s not cool to call someone’s kid ugly. I’m sure you were not intending to be hurtful, but I know too well engineers put their whole Hearts into such things and I’m always careful about that / rod, VA3ON On May 24, 2019, at 20:00, wrote: Wayne and interested others, Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was back in the day when almost every DXpedition was using K3's so it was obviously the radio to own. (Around 2009?) It was at the top of the Sherwood ratings. Owner's bragged, incessantly, about its Sherwood rating. After a period of time I grew to really dislike that radio. The audio was just plain awful and the man/machine interface was the worst I have ever seen. I detest bar graphs. I suppose if you play at ham radio 8 hours a day, seven days a week, the interface is "normal", even usable. For those of us who might get on the air for an hour or two a week, the controls were a mystery. Tap this button to do this, hold the same button for three seconds to do that, the list goes on. NOTHING was intuitive. It did not help that it was an incredibly ugly, too light and unsubstantial, radio. It's looks may have been barely acceptable when first introduced but it aged badly, rapidly. Over a ten year period it's price has become a real problem. There were many, many questions on this reflector regarding the controls, the same questions about the same controls, over and over and over again. That should have been a very large hint that the controls should be massively improved in any new radio. I sold my K3 and moved on to the big Japanese three, ANAN, and Flex, over the years. All had many, fairly easy to understand, controls. All were far, far more usable than the K3. Both the ANAN and Flex service departments are as good as Elecraft's. Eventually I left the Elecraft reflector, and that is a whole other story. Last week the K4 was announced so I rejoined the reflector. It sounded like a really great radio. Sadly, I have concluded it will be a dud, mostly because it is designed with the same philosophy as the K3 was, a small, compact, easily transportable radio, "a hallmark of Elecraft transceivers", to quote you, Wayne. From all that I have read, the controls will be even more complex. Ham radio operators are an aging group. Some suffer from the "fat finger" syndrome, others have vision problems, to name just two. The last thing they need or want is a tiny radio with minimal controls, each of which serves two or three or four or five purposes. They favor a radio that has many single or dual purpose knobs. They want bigger screens, the K4 screens are too small. I suggest you double the size of the radio and change your design criteria. Enlarging the physical size would not be a huge cost driver. Remember who your customers are. And when the Flex 6700 kicked the K3 out of first place in the Sherwood ratings in 2014, the Koolaid drinkers on this reflector were heard to say, "People put too much faith in numbers". Hypocrisy is thy name. I haven't stopped laughing. This email pertains to only the second and third paragraphs of Wayne's reply below. I wish Elecraft well with the K4 but I really think your minimalist/too complex way of designing needs to change. You've probably already guessed that I won't be a customer of the K4 as currently proposed. And you really, really ought to improve this reflector... 73, Harry K1RSA -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Wayne Burdick Sent: Friday, May 24, 2019 2:03 PM To: Elecraft Reflector ; k...@yahoogroups.com; elecraft...@groups.io Subject: [Elecraft] Elecraft K4 and Accessibility Hi Buddy et al, We've definitely been thinking about this. There's a paradigm shift going on in transceiver design, and we reached a point where we needed to embrace it. This shift is not entirely aligned with accessibility, as you know. I'll address alternatives in this email. As for the K4 specifically, its us
Re: [Elecraft] Elecraft K4 and Accessibility
Wayne and interested others, Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was back in the day when almost every DXpedition was using K3's so it was obviously the radio to own. (Around 2009?) It was at the top of the Sherwood ratings. Owner's bragged, incessantly, about its Sherwood rating. After a period of time I grew to really dislike that radio. The audio was just plain awful and the man/machine interface was the worst I have ever seen. I detest bar graphs. I suppose if you play at ham radio 8 hours a day, seven days a week, the interface is "normal", even usable. For those of us who might get on the air for an hour or two a week, the controls were a mystery. Tap this button to do this, hold the same button for three seconds to do that, the list goes on. NOTHING was intuitive. It did not help that it was an incredibly ugly, too light and unsubstantial, radio. It's looks may have been barely acceptable when first introduced but it aged badly, rapidly. Over a ten year period it's price has become a real problem. There were many, many questions on this reflector regarding the controls, the same questions about the same controls, over and over and over again. That should have been a very large hint that the controls should be massively improved in any new radio. I sold my K3 and moved on to the big Japanese three, ANAN, and Flex, over the years. All had many, fairly easy to understand, controls. All were far, far more usable than the K3. Both the ANAN and Flex service departments are as good as Elecraft's. Eventually I left the Elecraft reflector, and that is a whole other story. Last week the K4 was announced so I rejoined the reflector. It sounded like a really great radio. Sadly, I have concluded it will be a dud, mostly because it is designed with the same philosophy as the K3 was, a small, compact, easily transportable radio, "a hallmark of Elecraft transceivers", to quote you, Wayne. From all that I have read, the controls will be even more complex. Ham radio operators are an aging group. Some suffer from the "fat finger" syndrome, others have vision problems, to name just two. The last thing they need or want is a tiny radio with minimal controls, each of which serves two or three or four or five purposes. They favor a radio that has many single or dual purpose knobs. They want bigger screens, the K4 screens are too small. I suggest you double the size of the radio and change your design criteria. Enlarging the physical size would not be a huge cost driver. Remember who your customers are. And when the Flex 6700 kicked the K3 out of first place in the Sherwood ratings in 2014, the Koolaid drinkers on this reflector were heard to say, "People put too much faith in numbers". Hypocrisy is thy name. I haven't stopped laughing. This email pertains to only the second and third paragraphs of Wayne's reply below. I wish Elecraft well with the K4 but I really think your minimalist/too complex way of designing needs to change. You've probably already guessed that I won't be a customer of the K4 as currently proposed. And you really, really ought to improve this reflector... 73, Harry K1RSA -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Wayne Burdick Sent: Friday, May 24, 2019 2:03 PM To: Elecraft Reflector ; k...@yahoogroups.com; elecraft...@groups.io Subject: [Elecraft] Elecraft K4 and Accessibility Hi Buddy et al, We've definitely been thinking about this. There's a paradigm shift going on in transceiver design, and we reached a point where we needed to embrace it. This shift is not entirely aligned with accessibility, as you know. I'll address alternatives in this email. As for the K4 specifically, its user interface is dependent in part on use of the touch screen. This was simply the only way to integrate an equivalent of the K3S, P3, and all of the new hardware/software required to implement a direct-sampling radio. The use of a touch screen allows context sensitivity (physical overloading) for controls, making the K4 the equivalent of a much larger radio without touch. The resulting compact size is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a hallmark of Elecraft transceivers. Regarding accessibility, there are three possible approaches: 1. The K4's entire complement of controls, both hard and touch, will be represented by a set of "2-letter" commands. This API will be fully public as it is for our other transceivers. Presumably external devices or computers will be able to immediately make use of these commands to effect a flexible accessible interface. 2. In theory we could implement a large-target version of the LCD's touch controls, with proximity-based audio feedback and no panadapter. This would be a very ambitious project requiring ongoing supp
Re: [Elecraft] Elecraft K4 and Accessibility
Thanks Wayne, something to look forward to --David -Original Message- From: Wayne Burdick Sent: Friday, May 24, 2019 3:39 PM To: bear...@yahoo.com Cc: Buddy Brannan ; Elecraft Reflector ; k...@yahoogroups.com; blind-h...@groups.io Subject: Re: Elecraft K4 and Accessibility Short answer: yes, but I can't put a date on it yet. Wayne N6KR > On May 24, 2019, at 1:09 PM, David wrote: > > > Is it possible to get the audio CW feedback on the K4, or even the K3/K3S? > > --David > > > -Original Message- > From: elecraft-boun...@mailman.qth.net > On Behalf Of Buddy Brannan > Sent: Friday, May 24, 2019 11:26 AM > To: Wayne Burdick > Cc: Elecraft Reflector ; > k...@yahoogroups.com; blind-h...@groups.io > Subject: Re: [Elecraft] Elecraft K4 and Accessibility > > Hi Wayne, > > Thanks as always for your direct response. I appreciate your forthrightness > on this issue and willingness to tackle the more difficult > questions/aspects/design decision justifications. > > Elecraft has, as I stated in my original email, always been supportive of the > blind ham community inasmuch as design limitations and parameters allow, and > I for one appreciate your continuing commitment to that. Computer control > couldn’t be simpler on the Elecraft rigs I own. The Hampod is also a > fantastic accessory, and we appreciate your working with the developers of > these aids. > > I suspect that, were I able to get a higher end rig, I’d be opting for a K3 > for the exact reasons you specify. But I’m a knob and button kind of guy. I > think, were I interested in going whole hog for a K4, that your option (1) > seems to be the most straightforward path, certainly in the short term, to > get the mostbang for our accessibility buck, as it were. There’s lots of > flexibility there. > > I’m not sure what the state of the art is for touch screen accessibility > under GNU/Linux. I know there is a GNOME-based screen reader, as well as an > Android-based screen reader. Given the right clever people, it might be > possible to have an alternative UI, but, as you say, that would be a pretty > significant support issue for a pretty small market of users. But one could > potentially duplicate those controls on, say, an Amazon Fire or Android > tablet app. I think there really are possibilities for the right clever > people…shame I’m not one such. > > Again, I appreciate that Elecraft at least considers these issues, which is > more than I can say for many, many other companies. > > Vy 73, > > > Buddy Brannan, KB5ELV - Erie, PA > Email: bu...@brannan.name > Mobile: (814) 431-0962 > > > >> On May 24, 2019, at 2:02 PM, Wayne Burdick wrote: >> >> Hi Buddy et al, >> >> We've definitely been thinking about this. >> >> There's a paradigm shift going on in transceiver design, and we reached a >> point where we needed to embrace it. This shift is not entirely aligned with >> accessibility, as you know. I'll address alternatives in this email. >> >> As for the K4 specifically, its user interface is dependent in part on use >> of the touch screen. This was simply the only way to integrate an equivalent >> of the K3S, P3, and all of the new hardware/software required to implement a >> direct-sampling radio. The use of a touch screen allows context sensitivity >> (physical overloading) for controls, making the K4 the equivalent of a much >> larger radio without touch. The resulting compact size is still compatible >> with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a >> hallmark of Elecraft transceivers. >> >> Regarding accessibility, there are three possible approaches: >> >> 1. The K4's entire complement of controls, both hard and touch, will be >> represented by a set of "2-letter" commands. This API will be fully public >> as it is for our other transceivers. Presumably external devices or >> computers will be able to immediately make use of these commands to effect a >> flexible accessible interface. >> >> 2. In theory we could implement a large-target version of the LCD's touch >> controls, with proximity-based audio feedback and no panadapter. This would >> be a very ambitious project requiring ongoing support, similar to that >> needed for mobile/fixed app development. We don't have the staff to support >> this, so we'd need to engage the wider community to find a developer with >> suitable skills and motivation. The API or spec for such an effort doesn't >> exist at this time. >> >> 3. The K3S has very similar strong-signal perfor
Re: [Elecraft] Elecraft K4 and Accessibility
Short answer: yes, but I can't put a date on it yet. Wayne N6KR > On May 24, 2019, at 1:09 PM, David wrote: > > > Is it possible to get the audio CW feedback on the K4, or even the K3/K3S? > > --David > > > -Original Message- > From: elecraft-boun...@mailman.qth.net On > Behalf Of Buddy Brannan > Sent: Friday, May 24, 2019 11:26 AM > To: Wayne Burdick > Cc: Elecraft Reflector ; k...@yahoogroups.com; > blind-h...@groups.io > Subject: Re: [Elecraft] Elecraft K4 and Accessibility > > Hi Wayne, > > Thanks as always for your direct response. I appreciate your forthrightness > on this issue and willingness to tackle the more difficult > questions/aspects/design decision justifications. > > Elecraft has, as I stated in my original email, always been supportive of the > blind ham community inasmuch as design limitations and parameters allow, and > I for one appreciate your continuing commitment to that. Computer control > couldn’t be simpler on the Elecraft rigs I own. The Hampod is also a > fantastic accessory, and we appreciate your working with the developers of > these aids. > > I suspect that, were I able to get a higher end rig, I’d be opting for a K3 > for the exact reasons you specify. But I’m a knob and button kind of guy. I > think, were I interested in going whole hog for a K4, that your option (1) > seems to be the most straightforward path, certainly in the short term, to > get the mostbang for our accessibility buck, as it were. There’s lots of > flexibility there. > > I’m not sure what the state of the art is for touch screen accessibility > under GNU/Linux. I know there is a GNOME-based screen reader, as well as an > Android-based screen reader. Given the right clever people, it might be > possible to have an alternative UI, but, as you say, that would be a pretty > significant support issue for a pretty small market of users. But one could > potentially duplicate those controls on, say, an Amazon Fire or Android > tablet app. I think there really are possibilities for the right clever > people…shame I’m not one such. > > Again, I appreciate that Elecraft at least considers these issues, which is > more than I can say for many, many other companies. > > Vy 73, > > > Buddy Brannan, KB5ELV - Erie, PA > Email: bu...@brannan.name > Mobile: (814) 431-0962 > > > >> On May 24, 2019, at 2:02 PM, Wayne Burdick wrote: >> >> Hi Buddy et al, >> >> We've definitely been thinking about this. >> >> There's a paradigm shift going on in transceiver design, and we reached a >> point where we needed to embrace it. This shift is not entirely aligned with >> accessibility, as you know. I'll address alternatives in this email. >> >> As for the K4 specifically, its user interface is dependent in part on use >> of the touch screen. This was simply the only way to integrate an equivalent >> of the K3S, P3, and all of the new hardware/software required to implement a >> direct-sampling radio. The use of a touch screen allows context sensitivity >> (physical overloading) for controls, making the K4 the equivalent of a much >> larger radio without touch. The resulting compact size is still compatible >> with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a >> hallmark of Elecraft transceivers. >> >> Regarding accessibility, there are three possible approaches: >> >> 1. The K4's entire complement of controls, both hard and touch, will be >> represented by a set of "2-letter" commands. This API will be fully public >> as it is for our other transceivers. Presumably external devices or >> computers will be able to immediately make use of these commands to effect a >> flexible accessible interface. >> >> 2. In theory we could implement a large-target version of the LCD's touch >> controls, with proximity-based audio feedback and no panadapter. This would >> be a very ambitious project requiring ongoing support, similar to that >> needed for mobile/fixed app development. We don't have the staff to support >> this, so we'd need to engage the wider community to find a developer with >> suitable skills and motivation. The API or spec for such an effort doesn't >> exist at this time. >> >> 3. The K3S has very similar strong-signal performance and similar basic >> features, without touch. Since many of the added features of the K4 are >> panadapter-centric, a blind ham may very well find that the K3S is a viable >> alternative. No doubt there will be more used K3's and K3S's on the market >>
Re: [Elecraft] Elecraft K4 and Accessibility
What do people think about voice recognition? Recent Google Android phones do a decent job of voice recognition on the phone itself with no connection to the internet or cloud voice recogniton servers. There are open source voice recognition software applications that run on Linux. No idea how powerful the K4 processor is or how capable it might be to do this, but I'm throwing the idea out there. 73, Mark W7MLG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft K4 and Accessibility
You forgot to mention that "miracle of control" called the K-Pod. Without it, I would be chasing the K3 with a mouse via HRD (mouse or K-Pod sits on the edge of my desk within easy reach). I prefer to run without being tethered to a computer. A few extra buttons on the K-Pod would be great, but it is what it is and I appreciate it for what it is. A suggestion for the touch-screen users out there (IC-7300 and Fire Tablet in my station) is to use a stylus. Very accurate and does not crud up the screen. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Elecraft K4 and Accessibility
Is it possible to get the audio CW feedback on the K4, or even the K3/K3S? --David -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Buddy Brannan Sent: Friday, May 24, 2019 11:26 AM To: Wayne Burdick Cc: Elecraft Reflector ; k...@yahoogroups.com; blind-h...@groups.io Subject: Re: [Elecraft] Elecraft K4 and Accessibility Hi Wayne, Thanks as always for your direct response. I appreciate your forthrightness on this issue and willingness to tackle the more difficult questions/aspects/design decision justifications. Elecraft has, as I stated in my original email, always been supportive of the blind ham community inasmuch as design limitations and parameters allow, and I for one appreciate your continuing commitment to that. Computer control couldn’t be simpler on the Elecraft rigs I own. The Hampod is also a fantastic accessory, and we appreciate your working with the developers of these aids. I suspect that, were I able to get a higher end rig, I’d be opting for a K3 for the exact reasons you specify. But I’m a knob and button kind of guy. I think, were I interested in going whole hog for a K4, that your option (1) seems to be the most straightforward path, certainly in the short term, to get the mostbang for our accessibility buck, as it were. There’s lots of flexibility there. I’m not sure what the state of the art is for touch screen accessibility under GNU/Linux. I know there is a GNOME-based screen reader, as well as an Android-based screen reader. Given the right clever people, it might be possible to have an alternative UI, but, as you say, that would be a pretty significant support issue for a pretty small market of users. But one could potentially duplicate those controls on, say, an Amazon Fire or Android tablet app. I think there really are possibilities for the right clever people…shame I’m not one such. Again, I appreciate that Elecraft at least considers these issues, which is more than I can say for many, many other companies. Vy 73, Buddy Brannan, KB5ELV - Erie, PA Email: bu...@brannan.name Mobile: (814) 431-0962 > On May 24, 2019, at 2:02 PM, Wayne Burdick wrote: > > Hi Buddy et al, > > We've definitely been thinking about this. > > There's a paradigm shift going on in transceiver design, and we reached a > point where we needed to embrace it. This shift is not entirely aligned with > accessibility, as you know. I'll address alternatives in this email. > > As for the K4 specifically, its user interface is dependent in part on use of > the touch screen. This was simply the only way to integrate an equivalent of > the K3S, P3, and all of the new hardware/software required to implement a > direct-sampling radio. The use of a touch screen allows context sensitivity > (physical overloading) for controls, making the K4 the equivalent of a much > larger radio without touch. The resulting compact size is still compatible > with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a > hallmark of Elecraft transceivers. > > Regarding accessibility, there are three possible approaches: > > 1. The K4's entire complement of controls, both hard and touch, will be > represented by a set of "2-letter" commands. This API will be fully public as > it is for our other transceivers. Presumably external devices or computers > will be able to immediately make use of these commands to effect a flexible > accessible interface. > > 2. In theory we could implement a large-target version of the LCD's touch > controls, with proximity-based audio feedback and no panadapter. This would > be a very ambitious project requiring ongoing support, similar to that needed > for mobile/fixed app development. We don't have the staff to support this, so > we'd need to engage the wider community to find a developer with suitable > skills and motivation. The API or spec for such an effort doesn't exist at > this time. > > 3. The K3S has very similar strong-signal performance and similar basic > features, without touch. Since many of the added features of the K4 are > panadapter-centric, a blind ham may very well find that the K3S is a viable > alternative. No doubt there will be more used K3's and K3S's on the market > over the next year. The KX3 and KX2 provide audio CW feedback on most > controls and are another non-touch alternative. > > I hope the alternatives I've suggested to use of the K4's normal UI will be > helpful in most cases. > > 73, > Wayne > N6KR > > > > >> On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] >> wrote: >> >> [Sorry, sent this to Gary instead of the list] Hey Gary, >> >> I’m curious about this as well, as are others…see K8HSY’s post on the
Re: [Elecraft] Elecraft K4 and Accessibility
Hi Wayne, Thanks as always for your direct response. I appreciate your forthrightness on this issue and willingness to tackle the more difficult questions/aspects/design decision justifications. Elecraft has, as I stated in my original email, always been supportive of the blind ham community inasmuch as design limitations and parameters allow, and I for one appreciate your continuing commitment to that. Computer control couldn’t be simpler on the Elecraft rigs I own. The Hampod is also a fantastic accessory, and we appreciate your working with the developers of these aids. I suspect that, were I able to get a higher end rig, I’d be opting for a K3 for the exact reasons you specify. But I’m a knob and button kind of guy. I think, were I interested in going whole hog for a K4, that your option (1) seems to be the most straightforward path, certainly in the short term, to get the mostbang for our accessibility buck, as it were. There’s lots of flexibility there. I’m not sure what the state of the art is for touch screen accessibility under GNU/Linux. I know there is a GNOME-based screen reader, as well as an Android-based screen reader. Given the right clever people, it might be possible to have an alternative UI, but, as you say, that would be a pretty significant support issue for a pretty small market of users. But one could potentially duplicate those controls on, say, an Amazon Fire or Android tablet app. I think there really are possibilities for the right clever people…shame I’m not one such. Again, I appreciate that Elecraft at least considers these issues, which is more than I can say for many, many other companies. Vy 73, Buddy Brannan, KB5ELV - Erie, PA Email: bu...@brannan.name Mobile: (814) 431-0962 > On May 24, 2019, at 2:02 PM, Wayne Burdick wrote: > > Hi Buddy et al, > > We've definitely been thinking about this. > > There's a paradigm shift going on in transceiver design, and we reached a > point where we needed to embrace it. This shift is not entirely aligned with > accessibility, as you know. I'll address alternatives in this email. > > As for the K4 specifically, its user interface is dependent in part on use of > the touch screen. This was simply the only way to integrate an equivalent of > the K3S, P3, and all of the new hardware/software required to implement a > direct-sampling radio. The use of a touch screen allows context sensitivity > (physical overloading) for controls, making the K4 the equivalent of a much > larger radio without touch. The resulting compact size is still compatible > with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a > hallmark of Elecraft transceivers. > > Regarding accessibility, there are three possible approaches: > > 1. The K4's entire complement of controls, both hard and touch, will be > represented by a set of "2-letter" commands. This API will be fully public as > it is for our other transceivers. Presumably external devices or computers > will be able to immediately make use of these commands to effect a flexible > accessible interface. > > 2. In theory we could implement a large-target version of the LCD's touch > controls, with proximity-based audio feedback and no panadapter. This would > be a very ambitious project requiring ongoing support, similar to that needed > for mobile/fixed app development. We don't have the staff to support this, so > we'd need to engage the wider community to find a developer with suitable > skills and motivation. The API or spec for such an effort doesn't exist at > this time. > > 3. The K3S has very similar strong-signal performance and similar basic > features, without touch. Since many of the added features of the K4 are > panadapter-centric, a blind ham may very well find that the K3S is a viable > alternative. No doubt there will be more used K3's and K3S's on the market > over the next year. The KX3 and KX2 provide audio CW feedback on most > controls and are another non-touch alternative. > > I hope the alternatives I've suggested to use of the K4's normal UI will be > helpful in most cases. > > 73, > Wayne > N6KR > > > > >> On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] >> wrote: >> >> [Sorry, sent this to Gary instead of the list] >> Hey Gary, >> >> I’m curious about this as well, as are others…see K8HSY’s post on the >> blind-hams list. See also my response full of speculation (below). Wayne, >> please feel free to comment on my comments and correct me where I erred: >> >> I’ve been beating the accessibility drum on the Elecraft reflector for ages, >> and Wayne has assured that they would not go to all touch screen access, for >> that very reason. Elecraft has, in the person of one of their tech support >> people in the past, and Wayne in emails to me, committed to doing what they >> can in design parameters to make accessibility attainable, and they have >> been super cooperative
[Elecraft] Elecraft K4 and Accessibility
Hi Buddy et al, We've definitely been thinking about this. There's a paradigm shift going on in transceiver design, and we reached a point where we needed to embrace it. This shift is not entirely aligned with accessibility, as you know. I'll address alternatives in this email. As for the K4 specifically, its user interface is dependent in part on use of the touch screen. This was simply the only way to integrate an equivalent of the K3S, P3, and all of the new hardware/software required to implement a direct-sampling radio. The use of a touch screen allows context sensitivity (physical overloading) for controls, making the K4 the equivalent of a much larger radio without touch. The resulting compact size is still compatible with portable use (4.5" x 13.5" x 11", 10 pounds, and power-efficient), a hallmark of Elecraft transceivers. Regarding accessibility, there are three possible approaches: 1. The K4's entire complement of controls, both hard and touch, will be represented by a set of "2-letter" commands. This API will be fully public as it is for our other transceivers. Presumably external devices or computers will be able to immediately make use of these commands to effect a flexible accessible interface. 2. In theory we could implement a large-target version of the LCD's touch controls, with proximity-based audio feedback and no panadapter. This would be a very ambitious project requiring ongoing support, similar to that needed for mobile/fixed app development. We don't have the staff to support this, so we'd need to engage the wider community to find a developer with suitable skills and motivation. The API or spec for such an effort doesn't exist at this time. 3. The K3S has very similar strong-signal performance and similar basic features, without touch. Since many of the added features of the K4 are panadapter-centric, a blind ham may very well find that the K3S is a viable alternative. No doubt there will be more used K3's and K3S's on the market over the next year. The KX3 and KX2 provide audio CW feedback on most controls and are another non-touch alternative. I hope the alternatives I've suggested to use of the K4's normal UI will be helpful in most cases. 73, Wayne N6KR > On May 24, 2019, at 9:20 AM, Buddy Brannan bu...@brannan.name [KX3] > wrote: > > [Sorry, sent this to Gary instead of the list] > Hey Gary, > > I’m curious about this as well, as are others…see K8HSY’s post on the > blind-hams list. See also my response full of speculation (below). Wayne, > please feel free to comment on my comments and correct me where I erred: > > I’ve been beating the accessibility drum on the Elecraft reflector for ages, > and Wayne has assured that they would not go to all touch screen access, for > that very reason. Elecraft has, in the person of one of their tech support > people in the past, and Wayne in emails to me, committed to doing what they > can in design parameters to make accessibility attainable, and they have been > super cooperative with people like the Hampod folks and others who want to > design accessibility tools. > > The K4 has a full GNU/Linux computer built into it, and it’s got a > client/server architecture, with network access available, so it seems to me > accessibility should be possible, even relatively easy, to implement. > Especially given that there are still a wide range of physical buttons and > knobs on board. > > And, unlike Yaecomwoodlincotec, the principals at Elecraft are not only > available by email, but very responsive besides. If you’re really interested > in a perspective direct from the horse’s mouth, write to Wayne directly at > n...@elecraft.com. He really does answer email. > > Buddy Brannan, KB5ELV - Erie, PA > Email: bu...@brannan.name > Mobile: (814) 431-0962 > > > On May 23, 2019, at 1:47 PM, Gary Lee kb9...@arrl.net [KX3] > > wrote: > > > > could someone describe the front panel of the k4 with reference to that of > > the k3? With the added touch screen, I am wondering about usability for the > > blind operator. > > > > > > > > > __._,_.___ > Posted by: Buddy Brannan > Reply via web post• Reply to sender • Reply to group > • Start a New Topic • Messages in this topic (2) > VISIT YOUR GROUP > • Privacy • Unsubscribe • Terms of Use > > SPONSORED LINKS > > > > . > > > __,_._,___ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html