Hi,
"Why doesn’t the P3 signal strength agree with the K3S’s S-meter? You would
think the S-meter on the K3S and the signal displayed on the P3 would be the
same. There are several reasons why this might not be the case that have to do
with your display choices.
1.When the K3S SMTR MD menu is AbS, the K3S S-meter shows the
absolute signal at the antenna and does not change when the preamplifier or
attenuator are engaged. The signal at the antenna has an absolute power and
thus isn’t, nor should it be, affected by the K3S signal processing
preamplifier or attenuator. If the K3S SMTR MD menu is nor, changing the
preamplifier and attenuator will change the signal displayed on the K3S. This
shows you the affect of the preamplifier and attenuator. Meanwhile, if the K3S
and P3 serial ports are connected, the P3 knows the status of the preamplifier
and attenuator and adjusts its display accordingly. That is, the P3 always
operates in absolute mode showing you the power at the K3S antenna. So, when
SMTR MD menu is nor changing the preamplifier and attenuator will affect the
K3S S-meter but not the P3 display.
2.The signal level on the K3S and P3 depends on their respective
effective bandwidths. In the K3S the bandwidth is set by the pass band tuning
control. In the K3S the S-meter gives you a measure of the signal within the
K3S bandwidth. In the P3 the effective bandwidth is approximately the span
divided by 450 (there are 450 pixels displaying signals across the P3
display). In the P3 each pixel gives you a measure of the signal within the
effective bandwidth of the pixel. If the two bandwidths are different, the K3S
and P3 signal displays will be different.
This will particularly be evident with wideband signals such as SSB. Even when
the P3 span is 200 kHz its effective bandwidth per pixel is 440 Hz and it does
not contain the full signal that is seen on the K3S S-meter.
As an exercise, change to a relatively noisy band and change the width of the
pass band tuning. You should see less noise on the K3S display when the
bandwidth is narrower. While doing this you shouldn’t see any change in what
the P3 is displaying.
The bottom line here is “Don’t worry overmuch about the signal strength
readings.” Each display serves a different purpose. The K3S S-meter shows you
the signal strength of the signal(s) within its passband and the P3 shows you
the relative strengths of a number of signals shown in its span."
(excerpt from "The Elecraft K3s and P3").
Cheers,
Fred KE7X
For all KE7X Elecraft books, see www.ke7x.com<http://www.ke7x.com>
From: elecraft-boun...@mailman.qth.net on
behalf of IK4EWX
Sent: Saturday, August 18, 2018 1:00 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Elecraft P3 signal intensity
I have understood that it is normal that P3 with his extremely narrow IF give
lower S-units that the K3/K3S, but is it possible to adjust the P3 to give
same S-meter readings than my K3S?
Is there any way to give coherent signals intensity both K3 and P3?
On My P3 I read S6 a CW signal that is S9 on my k3S with his if 500hz wide.
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to fc...@ke7x.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com