[Elecraft] Firmware update process stalled K3
I wanted to install the latest firmware beta release (4.47). The process started, on the K3 display MCU LD appeared, but after a while the message appeared, that the update failed. The K3 stayed in the MCU LD mode and the K3 utility showed that there is a communication problem with the COM port. Trying to reactivate the COM communication failed with all possible COM ports my ELTIMA virtual port cable creates. Turning the K3 on and off didn't change anything, the MCU LD mode stays on. Also reinitializing the ports by turning the computer off and on again didn't change a thing, I could not get the COM port communication started again. Does anybody have an idea how to get back to normal without starting the EE INIT procedure (loosing all parameters)? Thanks in advance for your help!! Axel, DL3ZH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Firmware update process stalled K3
Yes, the firmware load was interrupted. Go through the procedure described in K3 Utility Help, Troubleshooting, MCU Boot Loader. 73 de Dick, K6KR -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Axel Kaiser Sent: Sunday, February 26, 2012 11:59 AM To: Elecraft Reflector Subject: [Elecraft] Firmware update process stalled K3 I wanted to install the latest firmware beta release (4.47). The process started, on the K3 display MCU LD appeared, but after a while the message appeared, that the update failed. The K3 stayed in the MCU LD mode and the K3 utility showed that there is a communication problem with the COM port. Trying to reactivate the COM communication failed with all possible COM ports my ELTIMA virtual port cable creates. Turning the K3 on and off didn't change anything, the MCU LD mode stays on. Also reinitializing the ports by turning the computer off and on again didn't change a thing, I could not get the COM port communication started again. Does anybody have an idea how to get back to normal without starting the EE INIT procedure (loosing all parameters)? Thanks in advance for your help!! Axel, DL3ZH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Firmware update process stalled K3
Thanks Dick for your help! It did do the job, I had to disconnect mymicroham microKeyer II , then it worked. So reading the help files sometimes really helps! Thanks again and 73 Axel, DL3ZH From: die...@comcast.net To: dl2...@hotmail.com; elecraft@mailman.qth.net Subject: RE: [Elecraft] Firmware update process stalled K3 Date: Sun, 26 Feb 2012 12:34:26 -0800 Yes, the firmware load was interrupted. Go through the procedure described in K3 Utility Help, Troubleshooting, MCU Boot Loader. 73 de Dick, K6KR -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Axel Kaiser Sent: Sunday, February 26, 2012 11:59 AM To: Elecraft Reflector Subject: [Elecraft] Firmware update process stalled K3 I wanted to install the latest firmware beta release (4.47). The process started, on the K3 display MCU LD appeared, but after a while the message appeared, that the update failed. The K3 stayed in the MCU LD mode and the K3 utility showed that there is a communication problem with the COM port. Trying to reactivate the COM communication failed with all possible COM ports my ELTIMA virtual port cable creates. Turning the K3 on and off didn't change anything, the MCU LD mode stays on. Also reinitializing the ports by turning the computer off and on again didn't change a thing, I could not get the COM port communication started again. Does anybody have an idea how to get back to normal without starting the EE INIT procedure (loosing all parameters)? Thanks in advance for your help!! Axel, DL3ZH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html