Re: [Elecraft] K2 digital mode questions
On 2/20/14 at 6:33 PM, w3...@embarqmail.com (Don Wilhelm) wrote: some [digital modes] like PSK31 will work with either [USB or LSB] PSK is a good mode to get working first because it can be inverted. You can use it to get all the details of computer <--> rig connection working and then if some other mode doesn't work, probably just a change of USB/LSB will get it working. (But watch out for speeds in RTTY.) Cheers - Bill, AE6JV --- Bill Frantz| Truth and love must prevail | Periwinkle (408)356-8506 | over lies and hate. | 16345 Englewood Ave www.pwpconsult.com | - Vaclav Havel | Los Gatos, CA 95032 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 digital mode questions
Dennis, Yes, the K2 takes care of the LSB/USB swap for bands 15 meters and above. Whether you want USB or LSB depends on the digital mode you are using. Most modes work in USB (RTTY REV) just fine (some like PSK31 will work with either), but RTTY itself typically uses LSB. 73, Don W3FPR On 2/20/2014 8:26 PM, Dennis Moore wrote: Thanks Don, I think I can get a handle on most of that except the swapping LSB/USB. If my interpretation is correct I should generally set the K2 to RTTY without Rev and it'll automatically select LSB or USB depending upon band? Rev would be used only in special circumstances? I'll dig through the parts box for a capacitor tomorrow, get the filters set up again, and give it a shot. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 digital mode questions
Thanks Don, I think I can get a handle on most of that except the swapping LSB/USB. If my interpretation is correct I should generally set the K2 to RTTY without Rev and it'll automatically select LSB or USB depending upon band? Rev would be used only in special circumstances? I'll dig through the parts box for a capacitor tomorrow, get the filters set up again, and give it a shot. Thanks. 73, Dennis On 2/19/2014 8:44 PM, Don Wilhelm wrote: Dennis, First a clarification - if the band is below 15 meters, RTTY is LSB and RTTY REV is USB. You don't have to worry about that on bands above 15 meters because the K2 automatically makes the corrective swap, but when aligning the filters, use a band below 15 meters so as not to mix the sidebands. Secondly, since you run out of range when aligning the 400 Hz filter width at 1000 Hz, your BFO range is not correct (too high) on the low frequency side. That can usually be corrected by adding a small value capacitor (10 pF to 22 pF) between the junction of the crystals and C174 and ground - a capacitor between pins 6 and 3 of U11 is a good place to insert it. Check the BFO range against the manual range limits after adding the capacitor and adjust the capacitor value as required. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 digital mode questions
Dennis, First a clarification - if the band is below 15 meters, RTTY is LSB and RTTY REV is USB. You don't have to worry about that on bands above 15 meters because the K2 automatically makes the corrective swap, but when aligning the filters, use a band below 15 meters so as not to mix the sidebands. Secondly, since you run out of range when aligning the 400 Hz filter width at 1000 Hz, your BFO range is not correct (too high) on the low frequency side. That can usually be corrected by adding a small value capacitor (10 pF to 22 pF) between the junction of the crystals and C174 and ground - a capacitor between pins 6 and 3 of U11 is a good place to insert it. Check the BFO range against the manual range limits after adding the capacitor and adjust the capacitor value as required. Once you have the BFO range corrected, you will have to re-align *all* your filters - SSB, CW and RTTY. You can refer to the filter alignment information on my website www.w3fpr.com - see part 3 of the K2 Dial Calibration article. The RTTY FL1 settings should be OP1 width, and the BFO settings should normally be the same as used for SSB LSB and USB. That filter will be the one normally used and works well with a full waterfall display. The problem comes in when a strong signal comes into the filter passband and activates the AGC such that the K2 receiver gain is reduced. All signals in the passband will be reduced because of the AGC action. The solution to that problem is to use a narrowed bandwidth (to get the strong signal out of the passband). That is the purpose of the narrow RTTY and RTTY REV filters. To accomplish that, I normally set FL2 to 1000 Hz, FL3 to 700 Hz and FL4 to 400 Hz. Those are the widths that I use, you are free to make your own choices on your desired filter widths. For the BFO frequencies of these narrow filters, the RTTY filters will be in the vicinity of 4912.xx and the RTTY REV filters will be in the vicinity of 4914.xx. Yes, use Spectrogram to set all the filters. The settings in the manual for SSB and CW will produce a workable set of filters, but they will not likely be optimum. One note on the SSB filters, be aware of the actual width of the SSB FL2, FL3 and FL4 filters. Many K2s in the serial number range near yours have varactors that make those filters much wider than indicated by the display on the K2. Make FL2 about 200 Hz more narrow than the FL1 OP1 width, FL3 about 200 Hz more narrow than FL2 and FL4 about 200 Hz even more narrow. Observing the actual filter width with Spectrogram will produce usable filters for reducing QRM from an interfering SSB signal on the high frequency side. The low frequency slope of the SSB filters should be placed close to the 300 Hz point on the Spectrogram display although the FL4 may be placed a bit higher (between 400 and 500 Hz). That will produce a set of SSB filters that can be progressively narrowed to maintain communications in the presence of interfering strong signals slightly off frequency. Now, if you followed all of that, you know as much as I do about aligning the K2 filters. 73, Don W3FPR On 2/19/2014 10:01 PM, Dennis Moore wrote: I'm trying to get my K2 (SN 5711) working on digital modes, initially just WSPR. I have the fixed audio output wired to pin 5 of the Mic header, going to a Signalink USB which is working fine. Audio in/out, keying, all just fine. If I transmit on WSPR my signal is being heard on 80m whether I'm in RTTY or RTTY REV. That in itself seems odd. I'm not able to decode any signals even though I can hear them. I'm having a hard time wrapping my brain around RTTY, RTTY REV, and when to use which mode. Also have questions about setting up the filters using Spectrogram. I've got the manual and I've searched the web for answers which probably just added to the confusion. First issue: RTTY & REV as it applies to USB/LSB On 80m, mode RTTY, am I transmitting on LSB or USB? If RTTY is LSB, when I switch to REV am I then transmitting on USB? Is that true on all bands? I read about sidebands switching above 17m on the K2. What exactly does that mean, and what effect does that have on which sideband I'm transmitting on? When would I use RTTY vs RTTY REV? If digital modes normally use USB, shouldn't I always be set to RTTY REV? Second issue: Setting up filters I read Don's advice regarding setting up filters for JT65 but it wasn't clear to me about BF2, BF3, BF4. Don said to center the filter at 1000 Hz, and that the high value should be used for RTTY REV and the low value should be used for RTTY. Say I have a filter setting of 700 Hz. In Spectrogram I see a 700 Hz wide noise signal, do I center the peak of that signal on 1000 Hz? I know that if I adjust the BF value to center on 1000 Hz at 4912.85 that I can keep adjusting the value until my noise disappears outside the filter and then will reappear and I can center it again on a value of 49
[Elecraft] K2 digital mode questions
I'm trying to get my K2 (SN 5711) working on digital modes, initially just WSPR. I have the fixed audio output wired to pin 5 of the Mic header, going to a Signalink USB which is working fine. Audio in/out, keying, all just fine. If I transmit on WSPR my signal is being heard on 80m whether I'm in RTTY or RTTY REV. That in itself seems odd. I'm not able to decode any signals even though I can hear them. I'm having a hard time wrapping my brain around RTTY, RTTY REV, and when to use which mode. Also have questions about setting up the filters using Spectrogram. I've got the manual and I've searched the web for answers which probably just added to the confusion. First issue: RTTY & REV as it applies to USB/LSB On 80m, mode RTTY, am I transmitting on LSB or USB? If RTTY is LSB, when I switch to REV am I then transmitting on USB? Is that true on all bands? I read about sidebands switching above 17m on the K2. What exactly does that mean, and what effect does that have on which sideband I'm transmitting on? When would I use RTTY vs RTTY REV? If digital modes normally use USB, shouldn't I always be set to RTTY REV? Second issue: Setting up filters I read Don's advice regarding setting up filters for JT65 but it wasn't clear to me about BF2, BF3, BF4. Don said to center the filter at 1000 Hz, and that the high value should be used for RTTY REV and the low value should be used for RTTY. Say I have a filter setting of 700 Hz. In Spectrogram I see a 700 Hz wide noise signal, do I center the peak of that signal on 1000 Hz? I know that if I adjust the BF value to center on 1000 Hz at 4912.85 that I can keep adjusting the value until my noise disappears outside the filter and then will reappear and I can center it again on a value of 4914.74. Should this high value should be used when I'm setting the filter for RTTY or RTTY REV? Third issue: BF4 running out of range As I'm trying to adjust the center of the signal at 1000 Hz the filter seems to run out of tuning range right before I get it centered, and the value of the BF jumps from it's low value to it's high value. I know that a lot of this is pretty basic but I'm just trying to get my thoughts on this straight. It seemed to be a lot easier getting my K3 up on WSPR but I think getting this K2/10 is just the thing for weak signal digital work. Thanks for any and all advice. 73, Dennis NJ6G __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
