Re: [Elecraft] K3/SteppIR setup
Clipped pin 7 wire and all is well. Both DX Lab's radio controller module and the logging module are listening to the K3. Thanks! From: "Joe Subich, W4TV" To: Jack Berry ; Elecraft Reflector Sent: Fri, November 25, 2011 4:04:16 PM Subject: Re: [Elecraft] K3/SteppIR setup On 11/25/2011 4:41 PM, Jack Berry wrote: > Cable from SteppIR is the S-13. The S-13 cable has a problem ... disconnect the wire at pin 7 on the transceiver end. SteppIR loops a TTL copy of RxD out on pin 7 and back in on pin 7. If there is a load on pin 7, the RxD can be compromised. > Tell me about AI, can't find that in the manual. AI is in the Programmer's guide and causes the K3 to send the IF data whenever the frequency/band/mode changes. It will not help if the transceiver is loading the TTL RxD signal. 73, ... Joe, W4TV On 11/25/2011 4:41 PM, Jack Berry wrote: > Cable from SteppIR is the S-13. I have the Y-cable as well but first just >trying > to get the SDA to track the radio. > The K3 has been working fine with DX-Lab logger and controller but not worried > about that yet. > Tell me about AI, can't find that in the manual. > > Thanks! > > > > > > From: "Joe Subich, W4TV" > To: Jack Berry; Elecraft Reflector > > Sent: Fri, November 25, 2011 3:33:09 PM > Subject: Re: [Elecraft] K3/SteppIR setup > > > Elecraft uses a modified Kenwood protocol. > > Have you enabled AI mode in the K3 and is a logging program running? > > What cable are you using to connect the K3 to SDA-100? > > Is the SDA-100 "Auto" mode turned on? > > > 73, > > ... Joe, W4TV > > > On 11/25/2011 4:27 PM, Jack Berry wrote: >> Should the Orion or Kenwood mode be selected when using the K3 with SteppIR's >> SDA-100 controller? Can't get it to work with either mode, just thought I > would >> check with the list. >> >> Thanks! >> Jack - WE5ST >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3/SteppIR setup
On 11/25/2011 4:41 PM, Jack Berry wrote: > Cable from SteppIR is the S-13. The S-13 cable has a problem ... disconnect the wire at pin 7 on the transceiver end. SteppIR loops a TTL copy of RxD out on pin 7 and back in on pin 7. If there is a load on pin 7, the RxD can be compromised. > Tell me about AI, can't find that in the manual. AI is in the Programmer's guide and causes the K3 to send the IF data whenever the frequency/band/mode changes. It will not help if the transceiver is loading the TTL RxD signal. 73, ... Joe, W4TV On 11/25/2011 4:41 PM, Jack Berry wrote: > Cable from SteppIR is the S-13. I have the Y-cable as well but first just > trying > to get the SDA to track the radio. > The K3 has been working fine with DX-Lab logger and controller but not worried > about that yet. > Tell me about AI, can't find that in the manual. > > Thanks! > > > > > > From: "Joe Subich, W4TV" > To: Jack Berry; Elecraft Reflector > > Sent: Fri, November 25, 2011 3:33:09 PM > Subject: Re: [Elecraft] K3/SteppIR setup > > > Elecraft uses a modified Kenwood protocol. > > Have you enabled AI mode in the K3 and is a logging program running? > > What cable are you using to connect the K3 to SDA-100? > > Is the SDA-100 "Auto" mode turned on? > > > 73, > > ... Joe, W4TV > > > On 11/25/2011 4:27 PM, Jack Berry wrote: >> Should the Orion or Kenwood mode be selected when using the K3 with SteppIR's >> SDA-100 controller? Can't get it to work with either mode, just thought I > would >> check with the list. >> >> Thanks! >> Jack - WE5ST >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3/SteppIR setup
Hi Jack, See K3 manual page 44 under Automatic Antenna Control. Set CONFIG:AUTOINF to Auto 1 73, Mike K2MK Jack Berry wrote > > Cable from SteppIR is the S-13. I have the Y-cable as well but first just > trying > to get the SDA to track the radio. > The K3 has been working fine with DX-Lab logger and controller but not > worried > about that yet. > Tell me about AI, can't find that in the manual. > > Thanks! > > > From: "Joe Subich, W4TV" <lists@> > To: Jack Berry <jlberry@>; Elecraft Reflector > <elecraft@.qth> > Sent: Fri, November 25, 2011 3:33:09 PM > Subject: Re: [Elecraft] K3/SteppIR setup > > > Elecraft uses a modified Kenwood protocol. > Have you enabled AI mode in the K3 and is a logging program running? > What cable are you using to connect the K3 to SDA-100? > Is the SDA-100 "Auto" mode turned on? > > 73, > ... Joe, W4TV > > > On 11/25/2011 4:27 PM, Jack Berry wrote: >> Should the Orion or Kenwood mode be selected when using the K3 with >> SteppIR's >> SDA-100 controller? Can't get it to work with either mode, just thought I > would >> check with the list. >> >> Thanks! >> Jack - WE5ST > -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-SteppIR-setup-tp7032430p7032454.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3/SteppIR setup
Cable from SteppIR is the S-13. I have the Y-cable as well but first just trying to get the SDA to track the radio. The K3 has been working fine with DX-Lab logger and controller but not worried about that yet. Tell me about AI, can't find that in the manual. Thanks! From: "Joe Subich, W4TV" To: Jack Berry ; Elecraft Reflector Sent: Fri, November 25, 2011 3:33:09 PM Subject: Re: [Elecraft] K3/SteppIR setup Elecraft uses a modified Kenwood protocol. Have you enabled AI mode in the K3 and is a logging program running? What cable are you using to connect the K3 to SDA-100? Is the SDA-100 "Auto" mode turned on? 73, ... Joe, W4TV On 11/25/2011 4:27 PM, Jack Berry wrote: > Should the Orion or Kenwood mode be selected when using the K3 with SteppIR's > SDA-100 controller? Can't get it to work with either mode, just thought I would > check with the list. > > Thanks! > Jack - WE5ST > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3/SteppIR setup
Elecraft uses a modified Kenwood protocol. Have you enabled AI mode in the K3 and is a logging program running? What cable are you using to connect the K3 to SDA-100? Is the SDA-100 "Auto" mode turned on? 73, ... Joe, W4TV On 11/25/2011 4:27 PM, Jack Berry wrote: > Should the Orion or Kenwood mode be selected when using the K3 with SteppIR's > SDA-100 controller? Can't get it to work with either mode, just thought I > would > check with the list. > > Thanks! > Jack - WE5ST > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3/SteppIR setup
Should the Orion or Kenwood mode be selected when using the K3 with SteppIR's SDA-100 controller? Can't get it to work with either mode, just thought I would check with the list. Thanks! Jack - WE5ST __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html