Re: [Elecraft] K3 - WSJT-X help
Steve, The KX3 has a built-in protection against audio overload. If there is too much audio, it shuts down the audio chain. Take a look at your mic gain setting on the KX3 - it is best set to mid-range. The resolution between steps is much greater at the low end and high end of the mic gain, and you may have difficulty setting for the proper number of ALC bars (in other words, the gain control is "touchy"). At mid-range, the steps are smaller and proper adjustment is easier. So if you have the mic gain set to a low level, work with the computer soundcard audio levels and the WSJT-X Power slider (misnamed because it is really an audio level control) to get them near a mid-position and allow the KX3 mic gain control will have a better range. 73, Don W3FPR On 12/7/2019 2:09 PM, stephen shearer wrote: YES, on my KX3.. I have seen (when I change modes, often) that I have zero ALC (not 4/5 bars). IF I turn the mike gain up, still zero. AT THIS POINT, I turn the mike gain to zero and start turning it up. The mike gain was too high and starting over works... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
YES, on my KX3.. I have seen (when I change modes, often) that I have zero ALC (not 4/5 bars). IF I turn the mike gain up, still zero. AT THIS POINT, I turn the mike gain to zero and start turning it up. The mike gain was too high and starting over works... FT8 is working again. I also run wsjt-x with 20db att so that I have "range" with the mike gain. OR what ever it might be with the K3... 73, steve WB3LGC On 11/13/19 7:39 AM, Don Wilhelm wrote: Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to sm.shearer...@gmail.com . __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
As I brought up this discussion, I should add: Many of the suggestions that the folks gave me really help with getting me going, but the one issue that should not have been an issue was the Audio settings in WJST. I had selected the K3 Audio out USB (I renamed my audio devices in Win10 so I know which USB sound device is which) My setting should have worked but it did not. I fixed it by setting audio output device as my computer speakers. Saved that settings. The went right back in and changed it to K3 Audio out. That fixed it. I would consider that issue is with WJST not the K3USB stuff. Rich On 11/13/2019 12:06 PM, N2TK via Elecraft wrote: Hi Bob, What is puzzling is why the audio settings were changed on WSJT. I surely wouldn't have gone into the program and make a change like that while running stations. 73, N2TK, Tony -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Bob McGraw K4TAX Sent: Wednesday, November 13, 2019 9:31 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Using Windows 10 Pro, I do use the computer for other audio activities, editing music, choir performances, listening to music and such. This will change the audio parameter settings of Windows.Thus one needs to understand the various selections and audio level values for the computer, the software and the radio. I use the USB input on my K3S and have a single USB cable which connects to the computer. I do not have or use a separate interface. I find this keeps things more reliable and less complex. The WSJT-X software sets the radio parameters when I open the application. I may need to tweak the computer levels a bit, depending on what I was doing last. Otherwise, it is solid and reliable. 73 Bob, K4TAX On 11/13/2019 8:22 AM, N4ZR wrote: I run into this over and over with Windows 10, and I'm embarrassed to say I often don't know what makes the difference. I use the microphone input and speakers output on an outboard USB sound card, and generally find myself just dinking around with the various sound settings until I find something that causes it to start working. My suspicion is that Windows 10 update has a nasty habit of resetting audio arrangements to some arbitrary set of "defaults." 73, Pete N4ZR Check out the Reverse Beacon Network at <http://reversebeacon.net>, now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX cluster. On 11/13/2019 8:10 AM, N2TK via Elecraft wrote: Don, Tnx for the reminder on checking the audio on the ALC meter. It was so long since I had a problem I forgot about doing that. There was no audio shown on the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. Changed it to what it was supposed to be and now I am fine. I have no idea what changed the setting as I was working station after station when this happened. Weird. 73, N2TK, Tony -Original Message- From: Don Wilhelm Sent: Wednesday, November 13, 2019 7:40 AM To: tony@verizon.net; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@comcast.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo
Re: [Elecraft] K3 - WSJT-X help
And if you are using a beam / directional antenna, the position of the antenna may affect the RF level at the operating position. 73 Bob, K4TAX On 11/13/2019 11:04 AM, N2TK via Elecraft wrote: I was on 20M at the time the problem arose. Will watch to see if it happens again as to what band and which antenna I am using. 73, N2TK, Tony From: Carl Yaffey Sent: Wednesday, November 13, 2019 10:40 AM To: tony@verizon.net Cc: Bob Gibson via Elecraft Subject: Re: [Elecraft] K3 - WSJT-X help I have had this happen intermittently when using the KPA1500 with my K3S. I’m pretty sure it’s an RF feedback issue with the PC + WSJT-X. Never happens when NOT on FT8. On Nov 13, 2019, at 7:04 AM, N2TK via Elecraft mailto:elecraft@mailman.qth.net> > wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. The typical setup is LP-Bridge, DXBase, DXBridge, WSJT-X. Yes, I know I need to update to DXLab to properly interface. So I closed everything but WSJT-X and have it talking directly to the K3. No difference. Also using the USB interface on the K3. Any ideas what could have happened and any suggestions? Maybe I bumped something? N2TK, Tony __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to cyaf...@gmail.com <mailto:cyaf...@gmail.com> Carl Yaffey K8NU Recording studio. cyaffey at gmail.com <http://gmail.com> 614 268 6353, Columbus OH http://www.carl-yaffey.com http://www.grassahol.com http://www.bluesswing.com Https://www.columbusfolkmusicsociety.org http://www.timbrewolves.carl-yaffey.com http://www.columbusshotokankarate.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
Hi Pete, Maybe it is just magic? 73, N2TK, Tony -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of N4ZR Sent: Wednesday, November 13, 2019 9:23 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help I run into this over and over with Windows 10, and I'm embarrassed to say I often don't know what makes the difference. I use the microphone input and speakers output on an outboard USB sound card, and generally find myself just dinking around with the various sound settings until I find something that causes it to start working. My suspicion is that Windows 10 update has a nasty habit of resetting audio arrangements to some arbitrary set of "defaults." 73, Pete N4ZR Check out the Reverse Beacon Network at <http://reversebeacon.net>, now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX cluster. On 11/13/2019 8:10 AM, N2TK via Elecraft wrote: > Don, > Tnx for the reminder on checking the audio on the ALC meter. It was so long > since I had a problem I forgot about doing that. There was no audio shown on > the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The > OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to > SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. > Changed it to what it was supposed to be and now I am fine. I have no idea > what changed the setting as I was working station after station when this > happened. > Weird. > > 73, > N2TK, Tony > > -Original Message- > From: Don Wilhelm > Sent: Wednesday, November 13, 2019 7:40 AM > To: tony@verizon.net; elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 - WSJT-X help > > Tony, > > Soundcard problem or K3 problem. This is most commonly a problem with audio > into the K3. > > How many bars illuminate on the ALC meter? It should be 4 with the 5th bar > flashing. If not, look at the audio levels. > > See the article on my website www.w3fpr.com > > 73, > Don W3FPR > > On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: >> Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, >> v2.0.1 when I no longer would get power out. >> >> WSJT is keying the K3 (Red transmit light is on) but no power out. >> The >> K3 keys fine with power out in CW or other modes is fine. WSJT is >> talking to the K3. WSJT shows the correct frequency, it is decoding >> and when I go into Settings > Radio and hit Test CAT it goes green. >> When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes >> on. But no power out. >> > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > n...@comcast.net > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to tony@verizon.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
Hi Bob, What is puzzling is why the audio settings were changed on WSJT. I surely wouldn't have gone into the program and make a change like that while running stations. 73, N2TK, Tony -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Bob McGraw K4TAX Sent: Wednesday, November 13, 2019 9:31 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Using Windows 10 Pro, I do use the computer for other audio activities, editing music, choir performances, listening to music and such. This will change the audio parameter settings of Windows.Thus one needs to understand the various selections and audio level values for the computer, the software and the radio. I use the USB input on my K3S and have a single USB cable which connects to the computer. I do not have or use a separate interface. I find this keeps things more reliable and less complex. The WSJT-X software sets the radio parameters when I open the application. I may need to tweak the computer levels a bit, depending on what I was doing last. Otherwise, it is solid and reliable. 73 Bob, K4TAX On 11/13/2019 8:22 AM, N4ZR wrote: > I run into this over and over with Windows 10, and I'm embarrassed to > say I often don't know what makes the difference. I use the > microphone input and speakers output on an outboard USB sound card, > and generally find myself just dinking around with the various sound > settings until I find something that causes it to start working. My > suspicion is that Windows 10 update has a nasty habit of resetting > audio arrangements to some arbitrary set of "defaults." > > 73, Pete N4ZR > Check out the Reverse Beacon Network > at <http://reversebeacon.net>, now > spotting RTTY activity worldwide. > For spots, please use your favorite > "retail" DX cluster. > > On 11/13/2019 8:10 AM, N2TK via Elecraft wrote: >> Don, >> Tnx for the reminder on checking the audio on the ALC meter. It was >> so long since I had a problem I forgot about doing that. There was no >> audio shown on the K3. What happened is that in WSJT-X > Settings > >> Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio >> CODEC). Somehow it changed to SPEAKERS (Realtek High Definition >> Audio), which is my audio for my pc. Changed it to what it was >> supposed to be and now I am fine. I have no idea what changed the >> setting as I was working station after station when this happened. >> Weird. >> >> 73, >> N2TK, Tony >> >> -----Original Message- >> From: Don Wilhelm >> Sent: Wednesday, November 13, 2019 7:40 AM >> To: tony@verizon.net; elecraft@mailman.qth.net >> Subject: Re: [Elecraft] K3 - WSJT-X help >> >> Tony, >> >> Soundcard problem or K3 problem. This is most commonly a problem >> with audio into the K3. >> >> How many bars illuminate on the ALC meter? It should be 4 with the >> 5th bar flashing. If not, look at the audio levels. >> >> See the article on my website www.w3fpr.com >> >> 73, >> Don W3FPR >> >> On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: >>> Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, >>> v2.0.1 when I no longer would get power out. >>> >>> WSJT is keying the K3 (Red transmit light is on) but no power out. >>> The >>> K3 keys fine with power out in CW or other modes is fine. WSJT is >>> talking to the K3. WSJT shows the correct frequency, it is decoding >>> and when I go into Settings > Radio and hit Test CAT it goes green. >>> When I hit TUNE on WSJT it turns to red and the red TX light on the >>> K3 comes on. But no power out. >>> >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net Please help support this >> email list: http://www.qsl.net/donate.html Message delivered to >> n...@comcast.net >> > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraf
Re: [Elecraft] K3 - WSJT-X help
I was on 20M at the time the problem arose. Will watch to see if it happens again as to what band and which antenna I am using. 73, N2TK, Tony From: Carl Yaffey Sent: Wednesday, November 13, 2019 10:40 AM To: tony@verizon.net Cc: Bob Gibson via Elecraft Subject: Re: [Elecraft] K3 - WSJT-X help I have had this happen intermittently when using the KPA1500 with my K3S. I’m pretty sure it’s an RF feedback issue with the PC + WSJT-X. Never happens when NOT on FT8. On Nov 13, 2019, at 7:04 AM, N2TK via Elecraft mailto:elecraft@mailman.qth.net> > wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. The typical setup is LP-Bridge, DXBase, DXBridge, WSJT-X. Yes, I know I need to update to DXLab to properly interface. So I closed everything but WSJT-X and have it talking directly to the K3. No difference. Also using the USB interface on the K3. Any ideas what could have happened and any suggestions? Maybe I bumped something? N2TK, Tony __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to cyaf...@gmail.com <mailto:cyaf...@gmail.com> Carl Yaffey K8NU Recording studio. cyaffey at gmail.com <http://gmail.com> 614 268 6353, Columbus OH http://www.carl-yaffey.com http://www.grassahol.com http://www.bluesswing.com Https://www.columbusfolkmusicsociety.org http://www.timbrewolves.carl-yaffey.com http://www.columbusshotokankarate.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
I have had this happen intermittently when using the KPA1500 with my K3S. I’m pretty sure it’s an RF feedback issue with the PC + WSJT-X. Never happens when NOT on FT8. > On Nov 13, 2019, at 7:04 AM, N2TK via Elecraft > wrote: > > Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 > when I no longer would get power out. > > WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 > keys fine with power out in CW or other modes is fine. WSJT is talking to > the K3. WSJT shows the correct frequency, it is decoding and when I go into > Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it > turns to red and the red TX light on the K3 comes on. But no power out. > > > > The typical setup is LP-Bridge, DXBase, DXBridge, WSJT-X. Yes, I know I need > to update to DXLab to properly interface. So I closed everything but WSJT-X > and have it talking directly to the K3. No difference. Also using the USB > interface on the K3. > > > > Any ideas what could have happened and any suggestions? Maybe I bumped > something? > > N2TK, Tony > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to cyaf...@gmail.com Carl Yaffey K8NU Recording studio. cyaffey at gmail.com 614 268 6353, Columbus OH http://www.carl-yaffey.com http://www.grassahol.com http://www.bluesswing.com Https://www.columbusfolkmusicsociety.org http://www.timbrewolves.carl-yaffey.com http://www.columbusshotokankarate.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
On my Macintosh, if I don't have the K3 USB connector plugged in at both ends when I start wsjt-x, it automatically reverts to the internal microphone and speaker. I usually catch the problem during my A to Z check of all the possible settings. 73 Bill AE6JV/1 On 11/13/19 at 8:10 AM, elecraft@mailman.qth.net (N2TK via Elecraft) wrote: Tnx for the reminder on checking the audio on the ALC meter. It was so long since I had a problem I forgot about doing that. There was no audio shown on the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. Changed it to what it was supposed to be and now I am fine. I have no idea what changed the setting as I was working station after station when this happened. --- Bill Frantz|The nice thing about standards| Periwinkle (408)356-8506 |is there are so many to choose| 16345 Englewood Ave www.pwpconsult.com |from. - Andrew Tanenbaum| Los Gatos, CA 95032 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
Using Windows 10 Pro, I do use the computer for other audio activities, editing music, choir performances, listening to music and such. This will change the audio parameter settings of Windows. Thus one needs to understand the various selections and audio level values for the computer, the software and the radio. I use the USB input on my K3S and have a single USB cable which connects to the computer. I do not have or use a separate interface. I find this keeps things more reliable and less complex. The WSJT-X software sets the radio parameters when I open the application. I may need to tweak the computer levels a bit, depending on what I was doing last. Otherwise, it is solid and reliable. 73 Bob, K4TAX On 11/13/2019 8:22 AM, N4ZR wrote: I run into this over and over with Windows 10, and I'm embarrassed to say I often don't know what makes the difference. I use the microphone input and speakers output on an outboard USB sound card, and generally find myself just dinking around with the various sound settings until I find something that causes it to start working. My suspicion is that Windows 10 update has a nasty habit of resetting audio arrangements to some arbitrary set of "defaults." 73, Pete N4ZR Check out the Reverse Beacon Network at <http://reversebeacon.net>, now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX cluster. On 11/13/2019 8:10 AM, N2TK via Elecraft wrote: Don, Tnx for the reminder on checking the audio on the ALC meter. It was so long since I had a problem I forgot about doing that. There was no audio shown on the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. Changed it to what it was supposed to be and now I am fine. I have no idea what changed the setting as I was working station after station when this happened. Weird. 73, N2TK, Tony -Original Message- From: Don Wilhelm Sent: Wednesday, November 13, 2019 7:40 AM To: tony@verizon.net; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@comcast.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
I run into this over and over with Windows 10, and I'm embarrassed to say I often don't know what makes the difference. I use the microphone input and speakers output on an outboard USB sound card, and generally find myself just dinking around with the various sound settings until I find something that causes it to start working. My suspicion is that Windows 10 update has a nasty habit of resetting audio arrangements to some arbitrary set of "defaults." 73, Pete N4ZR Check out the Reverse Beacon Network at <http://reversebeacon.net>, now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX cluster. On 11/13/2019 8:10 AM, N2TK via Elecraft wrote: Don, Tnx for the reminder on checking the audio on the ALC meter. It was so long since I had a problem I forgot about doing that. There was no audio shown on the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. Changed it to what it was supposed to be and now I am fine. I have no idea what changed the setting as I was working station after station when this happened. Weird. 73, N2TK, Tony -Original Message- From: Don Wilhelm Sent: Wednesday, November 13, 2019 7:40 AM To: tony@verizon.net; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@comcast.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
Don, Tnx for the reminder on checking the audio on the ALC meter. It was so long since I had a problem I forgot about doing that. There was no audio shown on the K3. What happened is that in WSJT-X > Settings > Audio > Soundcard, The OUTPUT was no longer Speakers (USB Audio CODEC). Somehow it changed to SPEAKERS (Realtek High Definition Audio), which is my audio for my pc. Changed it to what it was supposed to be and now I am fine. I have no idea what changed the setting as I was working station after station when this happened. Weird. 73, N2TK, Tony -Original Message- From: Don Wilhelm Sent: Wednesday, November 13, 2019 7:40 AM To: tony@verizon.net; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 - WSJT-X help Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: > Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, > v2.0.1 when I no longer would get power out. > > WSJT is keying the K3 (Red transmit light is on) but no power out. The > K3 keys fine with power out in CW or other modes is fine. WSJT is > talking to the K3. WSJT shows the correct frequency, it is decoding > and when I go into Settings > Radio and hit Test CAT it goes green. > When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes > on. But no power out. > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - WSJT-X help
Tony, Soundcard problem or K3 problem. This is most commonly a problem with audio into the K3. How many bars illuminate on the ALC meter? It should be 4 with the 5th bar flashing. If not, look at the audio levels. See the article on my website www.w3fpr.com 73, Don W3FPR On 11/13/2019 7:04 AM, N2TK via Elecraft wrote: Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 - WSJT-X help
Scratching my head. I was making Q's on FT8 with my K3 and WSJT-X, v2.0.1 when I no longer would get power out. WSJT is keying the K3 (Red transmit light is on) but no power out. The K3 keys fine with power out in CW or other modes is fine. WSJT is talking to the K3. WSJT shows the correct frequency, it is decoding and when I go into Settings > Radio and hit Test CAT it goes green. When I hit TUNE on WSJT it turns to red and the red TX light on the K3 comes on. But no power out. The typical setup is LP-Bridge, DXBase, DXBridge, WSJT-X. Yes, I know I need to update to DXLab to properly interface. So I closed everything but WSJT-X and have it talking directly to the K3. No difference. Also using the USB interface on the K3. Any ideas what could have happened and any suggestions? Maybe I bumped something? N2TK, Tony __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
