Re: [Elecraft] K3 ATU Problem
HI, After a bit of button pressing I have noticed the following: When doing a first tune using the internal ATU the tuning power is a set 5W. Immediately doing an extended tune the tuning power toggles to 10W. It does indeed flash up in the VFO B window whilst tuning is in progress. This is in no way controlled by any power level set by CONFIG>TUN PWR. My CONFIG>TUN power setting is 18W which I use to preset my Acom 1000 amp tuning. Regards, Mike VP8NO On 08/12/2021 15:42, Rick NK7I wrote: PS When using the tuner in the KPA1500 with the K3, it gets the 10 watts that I have as my default. I've not tested to see if that can be changed to any other value. I also attempted an ATU tune on the K3 into a dummy load, it's too fast for power to be displayed. ;-) 73, Rick NK7I On my K3, (Tech Mode on, just for clarity): Config | TUN PWR is set at 10.0 watts. If I want it set at another level, I turn the main VFO knob to set that level. I just tested that into a dummy load after setting the output per above to 9 watts and got 9 watts out (since reset to my default, 10). 73, Merry Christmas, Rick NK7I On 12/8/2021 8:34 AM, Tom Boucher wrote: *You can set TUN PWR in the K3 Config Menu to something other than 5 watts.73,DrewAF2Z* Drew, Page 60 of K3 Owner's Manual states: "TUN PWR Note 1: *TUN PWR* does not pertain to *ATU TUNE, *which always uses 5 or 10 W and is internally controlled" Does anyone know how to change the 'internal control' to increase from 5 W to 10 W? 73, Tom G3OLB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ATU Problem
PS When using the tuner in the KPA1500 with the K3, it gets the 10 watts that I have as my default. I've not tested to see if that can be changed to any other value. I also attempted an ATU tune on the K3 into a dummy load, it's too fast for power to be displayed. ;-) 73, Rick NK7I On my K3, (Tech Mode on, just for clarity): Config | TUN PWR is set at 10.0 watts. If I want it set at another level, I turn the main VFO knob to set that level. I just tested that into a dummy load after setting the output per above to 9 watts and got 9 watts out (since reset to my default, 10). 73, Merry Christmas, Rick NK7I On 12/8/2021 8:34 AM, Tom Boucher wrote: *You can set TUN PWR in the K3 Config Menu to something other than 5 watts.73,DrewAF2Z* Drew, Page 60 of K3 Owner's Manual states: "TUN PWR Note 1: *TUN PWR* does not pertain to *ATU TUNE, *which always uses 5 or 10 W and is internally controlled" Does anyone know how to change the 'internal control' to increase from 5 W to 10 W? 73, Tom G3OLB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rick.n...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ATU Problem
On my K3, (Tech Mode on, just for clarity): Config | TUN PWR is set at 10.0 watts. If I want it set at another level, I turn the main VFO knob to set that level. I just tested that into a dummy load after setting the output per above to 9 watts and got 9 watts out (since reset to my default, 10). 73, Merry Christmas, Rick NK7I On 12/8/2021 8:34 AM, Tom Boucher wrote: *You can set TUN PWR in the K3 Config Menu to something other than 5 watts.73,DrewAF2Z* Drew, Page 60 of K3 Owner's Manual states: "TUN PWR Note 1: *TUN PWR* does not pertain to *ATU TUNE, *which always uses 5 or 10 W and is internally controlled" Does anyone know how to change the 'internal control' to increase from 5 W to 10 W? 73, Tom G3OLB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rick.n...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ATU Problem
*You can set TUN PWR in the K3 Config Menu to something other than 5 watts.73,DrewAF2Z* Drew, Page 60 of K3 Owner's Manual states: "TUN PWR Note 1: *TUN PWR* does not pertain to *ATU TUNE, *which always uses 5 or 10 W and is internally controlled" Does anyone know how to change the 'internal control' to increase from 5 W to 10 W? 73, Tom G3OLB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ATU problem
If an ATU tune finishes like that, with --, then it did not find a match! (and will be in a random state). You don't have enough power for a successful Tune. Try running the TX gain calibration with the K3 Utility. Or, with a dummy load, ATU in BYP, make sure TUN PWR is at "nor", then set pwr to 5.0 watts exactly and long press XMIT to send a carrier for several seconds. (That will do a manual tx gain cal on that freq). Then engage ATU and do an ATU TUNE and it should find a match. If the TX gain cal fails, something is wrong with the LPA. Keith WE6R Elecraft Tech. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ATU problem
First thought, is your ATU is in bypass? Is the "ATU" icon showing below the 4th digit of VFO A display? 73, Fred ["Skip"] K6DGW Sparks NV DM09dn Washoe County On 1/13/2021 6:43 AM, Eric Rosenberg wrote: When I tap ATU TUNE, I hear the relays clicking, see no output from the radio. The op right corner of the screen shows "--" When I then transit, it appears that the SWR hasn't changed... the tuner hasn't actually done anything, Is there a way to troubleshoot this? Thanks & 73, Eric W3DQ Washington, DC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ATU problem
When I tap ATU TUNE, I hear the relays clicking, see no output from the radio. The op right corner of the screen shows "--" When I then transit, it appears that the SWR hasn't changed... the tuner hasn't actually done anything, Is there a way to troubleshoot this? Thanks & 73, Eric W3DQ Washington, DC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 ATU problem
Mark, Do you have the correct antenna (ANT1/ANT2) selected (this is a per band setting)? Have you tried it by tuning into a dummy load? If it tunes into a dummy load, then you will likely find your problem in your antenna system. 73, Don W3FPR On 4/20/2018 2:01 AM, Bonjour de Marc ! , F4TXR wrote: Hello everyone ! , I have a problem that suddenly happened, my atu on my k3 does not work more correctly! we can hear him agree, but it's like she does not find him as a result, the ROS remains high, regardless of the bands. Everything else seems to work well Maybe a manipulation to do reset Thank you all for your close cooperation, Mark __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 ATU problem
Hello everyone ! , I have a problem that suddenly happened, my atu on my k3 does not work more correctly! we can hear him agree, but it's like she does not find him as a result, the ROS remains high, regardless of the bands. Everything else seems to work well Maybe a manipulation to do reset Thank you all for your close cooperation, Mark -- Pour une petite présentation , n'hésitez pas à visiter ma page sur QRZ.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com