[Elecraft] K3S macro
Is there a K3S macro to set the radio to USB? I know about BR0; BR1; BR2; and BR3; Ed W0SD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S Macro Settings
Is it possible to set M1 and M2 to macros? I seem to be able to set M3 and M4 OK to modify TX EQ or FLAT. I’ve not been able to assign to M1 or M2 any macro. On the K3 I assigned them to a sequence of DN7;DN7; … DN7 or the UP7 equivalent so that with those two buttons I could easily QSY up or down 50 kHz. The K3S responds with a “SET” response, but the execution does not work. The macros are a simple sequence of DN7;DN7;DN7 repeated ten times. I figure I’m missing something. Those macros worked FB on the K3. They work FB from the K3 Utility, current version. They can be set FB into the K3S. But the execution is ignored. All help appreciated. 73/Gary W2CS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S macro
Mode up: SWT17; Mode dn: SWT18; LSB: MD1; USB: MD2; __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S macro
MD2; will set the mode to USB From the Programmer's Reference "SET/RSP format: MDn; or MD$n; where n is 1 (LSB), 2 (USB), 3 (CW), 4 (FM), 5 (AM), 6 (DATA), 7 (CWREV), or 9 (DATA-REV)..." Mike - KI0HA On 1/31/2018 23:57, Ed Gray W0SD wrote: Is there a K3S macro to set the radio to USB? I know about BR0; BR1; BR2; and BR3; Ed W0SD __ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S macro
Judging from the context, I would bet the question was asking about the _other_ USB - Universal Serial Bus, which is present in the K3S. No, I don’t know the answer… - Jack, W6FB > On Jan 31, 2018, at 10:56 PM, Michael Eberle wrote: > > MD2; will set the mode to USB > > From the Programmer's Reference > > "SET/RSP format: MDn; or MD$n; where n is 1 (LSB), 2 (USB), 3 (CW), 4 (FM), 5 > (AM), 6 (DATA), 7 (CWREV), or 9 (DATA-REV)..." > > Mike - KI0HA > > > On 1/31/2018 23:57, Ed Gray W0SD wrote: >> Is there a K3S macro to set the radio to USB? I know about BR0; BR1; BR2; >> and BR3; >> >> Ed W0SD >> >> __ > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to jackbrin...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro AUX
Verzonden vanaf mijn Samsung Galaxy-smartphone. I would like to control the Bset AUX with a macro.An SWT command works, but does not give a defined state. It just switches between main and aux.Is there a command which forces AUX in a defined state, no matter its current setting.73 HenkPA0C __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S Macro command XIT
Hi I'm finally diving into setting up command macros, and most are successful. I thought there was a way to not only turn on XIT, but to also be able to set an up or down offset. I've tried several different command combinations, but no luck. XIT turns on but no offset. Is there not a command string that turns on XIT and allows an UP or DN offset? Thanks Gene, N9TF K3S 10057 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S Macro Programming - Rotating Macros
I am trying to program my first "Rotating Macro", where the PF1 Button will set SPLIT+1 the first time it is pressed and held and it will UNSET SPLIT the second time it is pressed and held. I am basing this on the work by W8TN and LA3ZA, and others who have offered support here. I have had PF1 as SPLIT+1 and PF2 as SPLIT+5. They are saved in MACRO1 and MACRO2, respectively. I am trying to add MACRO3 and MACRO4 to CLEAR SPLIT and set to SPLIT+1 and SPLIT+5 again. I added the following to MACRO1 based on the Programmers reference: MN110;SWT20;SWH18;SWT14; #20 is listed as MACRO3, #18 is listed as PF1. But, the SPLIT part of the MACRO works, but the MACRO is not reprogrammed. So, little joy. When I execute the MACROs from K3 Utility, the reprogram things fine. But not when I hold the button. I hope I don't have to "add" these in CONFIG every time. That doesn't make sense. (100) 72, Byron __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro command XIT
To set a specific RIT/XIT offset, you can use the RO command. From the programmer's reference: SET format: ROs where s is +/- and is -. s can also be a space in lieu of +. 73, Wayne N6KR On Jul 7, 2016, at 7:07 PM, "Gene Gabry" wrote: > Hi > > > > I'm finally diving into setting up command macros, and most are successful. > I thought there was a way to not only turn on XIT, but to also be able to > set an up or down offset. I've tried several different command combinations, > but no luck. XIT turns on but no offset. > > Is there not a command string that turns on XIT and allows an UP or DN > offset? > > > > Thanks > > > > Gene, N9TF > > > > K3S 10057 > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to n...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro command XIT
Thanks Wayne! That did it. I don't know how I missed that command string. This phase of the K3S is all pretty much Greek to me, and I've read over the programming manual several times trying to absorb it all before experimenting. After a year of pushing buttons and turning knobs, I am finally writing commands for functions I use most and want a one touch button to get there fast. Thanks again and 73 Gene, N9TF To set a specific RIT/XIT offset, you can use the RO command. From the programmer's reference: SET format: ROs where s is +/- and is -. s can also be a space in lieu of +. 73, Wayne N6KR On Jul 7, 2016, at 7:07 PM, "Gene Gabry" wrote: > Hi > > > > I'm finally diving into setting up command macros, and most are successful. > I thought there was a way to not only turn on XIT, but to also be able > to set an up or down offset. I've tried several different command > combinations, but no luck. XIT turns on but no offset. > > Is there not a command string that turns on XIT and allows an UP or DN > offset? > > > > Thanks > > > > Gene, N9TF > > > > K3S 10057 > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > n...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S Macro Command MICSEL question
I am wondering if there is a more direct command to toggle between the MIC SEL FP and MIC SEL RP other than having to use the UP/DN command? These are the two command statements I am using to switch between the two with FP.H being the normal home position. To switch to RP (Bias and H already activated) = MN053;UP;CP015;MG003;MN255; To switch back to FP.H (H already activated) = MN053;DN;CP018;MG025;MN255; Is there another command or address to directly activate the actual mic location other than toggling MN up and down? I just want to switch between those two locations. Thanks Gene, N9TF K3S 10057 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro Programming - Rotating Macros
This is an RTFM problem. I was confusing the KX3 Table with the K3 Table. When I used the proper values from the K3 Table, it worked perfectly. 73, Byron MACRO1-4: #11, 12, 13, 24 PF1-PF2: #45, 47 On 08/13/2015 08:14 PM, Byron Peebles wrote: I am trying to program my first "Rotating Macro", where the PF1 Button will set SPLIT+1 the first time it is pressed and held and it will UNSET SPLIT the second time it is pressed and held. I am basing this on the work by W8TN and LA3ZA, and others who have offered support here. I have had PF1 as SPLIT+1 and PF2 as SPLIT+5. They are saved in MACRO1 and MACRO2, respectively. I am trying to add MACRO3 and MACRO4 to CLEAR SPLIT and set to SPLIT+1 and SPLIT+5 again. I added the following to MACRO1 based on the Programmers reference: MN110;SWT20;SWH18;SWT14; #20 is listed as MACRO3, #18 is listed as PF1. But, the SPLIT part of the MACRO works, but the MACRO is not reprogrammed. So, little joy. When I execute the MACROs from K3 Utility, the reprogram things fine. But not when I hold the button. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S Macro issue with AGC SLP
I'm trying to set the AGC SLP in a macro. Currently using the K3 utility to test. I have Tech MD On Evoking the following line does NOT change the value for AGC SLP MN017;MP001;SWT14; I've used variations and cannot get the macro to change the setting. When I evoke a similar command for AGC TH it works MN017;MP008;SWT14; After evoking MN017;MP001;SWT14; Issuing the commands MP; returns ?; which per the book indicates the radio is busy. I'm sure it's something I'm doing wrong. Thanks in advance. Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro issue with AGC SLP
And just a heads up. Elecraft support considers macros to be "programming". As a software support engineer I can tell you that statement makes professional programmers drink to excess. If you want/need macro support we're asked to email k3supp...@elecraft.com so the request can be forwarded to their programmer and/or the reflector. Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of ae...@carolinaheli.com Sent: Monday, October 12, 2015 1:54 PM To: k3supp...@elecraft.com Cc: elecraft@mailman.qth.net Subject: [Elecraft] K3S Macro issue with AGC SLP I'm trying to set the AGC SLP in a macro. Currently using the K3 utility to test. I have Tech MD On Evoking the following line does NOT change the value for AGC SLP MN017;MP001;SWT14; I've used variations and cannot get the macro to change the setting. When I evoke a similar command for AGC TH it works MN017;MP008;SWT14; After evoking MN017;MP001;SWT14; Issuing the commands MP; returns ?; which per the book indicates the radio is busy. I'm sure it's something I'm doing wrong. Thanks in advance. Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to je...@carolinaheli.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro issue with AGC SLP
Hi Jerry, I talked to Howard about this and he wasn't trying to say it was 'programming' in the usual software context. :-) Many of our customers refer to Macro's as 'programming' the radio, and he was just talking in that context :-) His request for an email to K3support (which goes immediately to him and several other support engineers) is normal since he isn't an expert in all K3 macros and sending to k3support helps us understand more exactly what you were trying to do, and it gets to all of our support staff -immediately- so the one most qualified to help can respond to you (or get back to Howard to help him respond). 73, Eric /elecraft.com/ On 10/12/2015 11:39 AM, ae...@carolinaheli.com wrote: And just a heads up. Elecraft support considers macros to be "programming". As a software support engineer I can tell you that statement makes professional programmers drink to excess. If you want/need macro support we're asked to email k3supp...@elecraft.com so the request can be forwarded to their programmer and/or the reflector. Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of ae...@carolinaheli.com Sent: Monday, October 12, 2015 1:54 PM To: k3supp...@elecraft.com Cc: elecraft@mailman.qth.net Subject: [Elecraft] K3S Macro issue with AGC SLP I'm trying to set the AGC SLP in a macro. Currently using the K3 utility to test. I have Tech MD On Evoking the following line does NOT change the value for AGC SLP MN017;MP001;SWT14; I've used variations and cannot get the macro to change the setting. When I evoke a similar command for AGC TH it works MN017;MP008;SWT14; After evoking MN017;MP001;SWT14; Issuing the commands MP; returns ?; which per the book indicates the radio is busy. I'm sure it's something I'm doing wrong. Thanks in advance. Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to je...@carolinaheli.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to eric.swa...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro issue with AGC SLP
Jerry, Some K3S/K3 menu entries don't yet support the MP command (remote parameter GET/SET). See Table 5 of the Programmer's Reference. Since you asked, I'll add MP command support for the AGC SLP menu entry in the next firmware release. 73, Wayne N6KR >> >> -Original Message- >> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of >> ae...@carolinaheli.com >> Sent: Monday, October 12, 2015 1:54 PM >> To: k3supp...@elecraft.com >> Cc: elecraft@mailman.qth.net >> Subject: [Elecraft] K3S Macro issue with AGC SLP >> >> I'm trying to set the AGC SLP in a macro. Currently using the K3 utility to >> test. >> >> I have Tech MD On >> >> >> Evoking the following line does NOT change the value for AGC SLP >> >> MN017;MP001;SWT14; __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S Macro issue with AGC SLP
Thanks Eric, It just hit me wrong. I'm a Systems Analyst ($4 title for a high level software support engineer), amateur programmer (.net C#, C), and scripter (MS DOS, DR DOS, Powershell, ASP, VB, Java). My expectation wasn't for support to be a subject matter expert on macros. I just had a basic question because I expect the issue is my syntax. No worries. I have a working macro that's clumsy and not very efficient. I found the DN command for that attribute works. I'd much prefer a direct entry value even if it had to be a hex value 0-F instead of a string of 'DN;'. Playing with the AGC seems to have fixed the concerns I have with the receiver sensitivity. At the defaults the rig works very well but was acting hard of hearing. What I've found is based on the antenna and QTH receive conditions there are settings on the AGC with the DSP engaged that pull the signals out VERY WELL. As expected the issues I'm experiencing are just learning curve type opportunities. I'm glad I purchased the K3 book and have the K3S book on pre-order. It's definitely worth having. Jer Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Eric Swartz - WA6HHQ, Elecraft Sent: Monday, October 12, 2015 4:35 PM To: ae...@carolinaheli.com; k3supp...@elecraft.com Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3S Macro issue with AGC SLP Hi Jerry, I talked to Howard about this and he wasn't trying to say it was 'programming' in the usual software context. :-) Many of our customers refer to Macro's as 'programming' the radio, and he was just talking in that context :-) His request for an email to K3support (which goes immediately to him and several other support engineers) is normal since he isn't an expert in all K3 macros and sending to k3support helps us understand more exactly what you were trying to do, and it gets to all of our support staff -immediately- so the one most qualified to help can respond to you (or get back to Howard to help him respond). 73, Eric /elecraft.com/ On 10/12/2015 11:39 AM, ae...@carolinaheli.com wrote: > And just a heads up. Elecraft support considers macros to be "programming". > As a software support engineer I can tell you that statement makes > professional programmers drink to excess. > > If you want/need macro support we're asked to email k3supp...@elecraft.com > so the request can be forwarded to their programmer and/or the reflector. > > > Jerry Moore > CDXA, INDEXA, SKCC, Fists > AE4PB, K3S - S.N. 010324 > http://www.qrz.com/db/AE4PB > An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and > Patriotic. > > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of > ae...@carolinaheli.com > Sent: Monday, October 12, 2015 1:54 PM > To: k3supp...@elecraft.com > Cc: elecraft@mailman.qth.net > Subject: [Elecraft] K3S Macro issue with AGC SLP > > I'm trying to set the AGC SLP in a macro. Currently using the K3 utility to > test. > > I have Tech MD On > > > > Evoking the following line does NOT change the value for AGC SLP > > MN017;MP001;SWT14; > > > > I've used variations and cannot get the macro to change the setting. > > When I evoke a similar command for AGC TH it works > > MN017;MP008;SWT14; > > > > > > After evoking MN017;MP001;SWT14; > > Issuing the commands MP; returns ?; which per the book indicates the radio > is busy. > > > > I'm sure it's something I'm doing wrong. > > > > Thanks in advance. > > > > > > > > Jerry Moore > > CDXA, INDEXA, SKCC, Fists > > AE4PB, K3S - S.N. 010324 > > http://www.qrz.com/db/AE4PB > > An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and > Patriotic. > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to je...@carolinaheli.com > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Pl
Re: [Elecraft] K3S Macro issue with AGC SLP
Thanks Wayne, I don't expect to change the settings often, just once during a contest, and once outside of contesting. Knowing me I'll likely play with the settings a lot to better understand what they are doing. I'm hearing A LOT more now that I've started adjusting. Jer Jerry Moore CDXA, INDEXA, SKCC, Fists AE4PB, K3S - S.N. 010324 http://www.qrz.com/db/AE4PB An Amateur is - Considerate, Loyal, Progressive, Friendly, Balanced, and Patriotic. -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick Sent: Monday, October 12, 2015 4:47 PM To: ae...@carolinaheli.com Cc: k3supp...@elecraft.com; Elecraft Reflector; Eric Swartz - WA6HHQ, Elecraft Subject: Re: [Elecraft] K3S Macro issue with AGC SLP Jerry, Some K3S/K3 menu entries don't yet support the MP command (remote parameter GET/SET). See Table 5 of the Programmer's Reference. Since you asked, I'll add MP command support for the AGC SLP menu entry in the next firmware release. 73, Wayne N6KR >> >> -Original Message- >> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of >> ae...@carolinaheli.com >> Sent: Monday, October 12, 2015 1:54 PM >> To: k3supp...@elecraft.com >> Cc: elecraft@mailman.qth.net >> Subject: [Elecraft] K3S Macro issue with AGC SLP >> >> I'm trying to set the AGC SLP in a macro. Currently using the K3 >> utility to test. >> >> I have Tech MD On >> >> >> Evoking the following line does NOT change the value for AGC SLP >> >> MN017;MP001;SWT14; __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to je...@carolinaheli.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3S macro to select FrontPanel (mic) or LineIn (codec)?
For phone contesting, I would like to select the LineIn codec, transmit a wav file, then revert to FrontPanel mic input. I have the K3S successfully transmitting the wav audio via its codec input, but not the source switching back-and-forth. The programmer's reference lists a command that enables both LineIn + FrontPanel simultaneously - which is unacceptable. The programmer's reference describes the use of MP and MQ Menu Selections (i.e. MN053) and then refer to using " UP / DN to alter the settings." I do not know how to combine those macros for source switching. Is there a way to make this work? Thanks in advance for any advice, -larry (K8UT) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
