[Elecraft] Spectrogram help
Old age must be kicking in :( I originally aligned the K2 using Spectrogram and it worked great. I am doing a realignment and am lost. I am running a DSP unit and it appears that Toms instructions say that if you are running either DSP or Audio options you need to turn the AFIL off in the K2 Menu AND set the in/out switch to OUT on the PC board. Well to start, I dont see a AFIL in the K2 menu and dont see any switches, jumpers, etc on the DSP board. What am I missing? Thanks and 73, Rich kd0zv ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spectrogram help
Well to start, I dont see a AFIL in the K2 menu and dont see any switches, jumpers, etc on the DSP board. Put the DSP in BYPASS mode. 73, Lyle KK7P ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Spectrogram help
Rich, Rather than attempting to walk you through the steps to bypass the KDSP2 (it is in the KDSP2 menu which is kicked in with the DISPLAY button, not AFIL). I suggest you drag out the KDSP2 manual and follow the instructions to put it into bypass state. Actually, I never remember the exact sequence myself, so I just look it up when I need to do it. 73, Don W3FPR -Original Message- Old age must be kicking in :( I originally aligned the K2 using Spectrogram and it worked great. I am doing a realignment and am lost. I am running a DSP unit and it appears that Toms instructions say that if you are running either DSP or Audio options you need to turn the AFIL off in the K2 Menu AND set the in/out switch to OUT on the PC board. Well to start, I dont see a AFIL in the K2 menu and dont see any switches, jumpers, etc on the DSP board. What am I missing? Thanks and 73, Rich kd0zv ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.375 / Virus Database: 268.1.0/269 - Release Date: 2/24/2006 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Spectrogram help
I must be doing something wrong. Have my BFO settings exactly as specified in the K2 manual on CW. Using the noise gen from Elecraft. However, during the BFO settings per the K2 manual, FL2-FL4 at the BFO settings they specify results in almost no audio coming from the speaker using the N-gen. Then, when I go to spectrogram, my entire curve for FL1 is to the right of 600Hz on this display and no matter what I do with the vfo knob, there is no shifting of the curve to speak of and just changes in amplitude. On FL2-FL4, there is no amplitude at all but I can then adjust the VFO and see/hear the Ngen signals coming thru but the entire curve is still to the right of 600Hz. Running spectrogram off the headphone jack to my sound card. During operation, my CW mode audio level is considerably below the LSB or USB level and my receive CW signals seem to turn to clicks at audio freq below 800Hz or so.what have I missed? Thx K5GUS Dan ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spectrogram help
Dan! Pick one filter and start playing with the bfo setting in cal fil. Note the change on spectrogram. Also change to speaker out on rear of the rig and adjust AF to suitable setting. The speaker output will give you full range on audiospectre. If you move bfo and it move wrong way? Simply move it the other way. But first you must decide what pitch you want on cw and begin from there. Pick fl2 and decide bandwith. Put markers in spectrogram. If you want 700bw on fl2 and pitch 600hz you put one marker 350hz below and one marker 350hz higher than 600hz on spectrogram. Now you adjust bfo until bandnoice is sentered within the two markers. Repeat with other modes and filters. Don't forget CW-r and RTTY-r. I think this will do it for you. Have a nice weekend Dan. Tom LA1PHA - Original Message - From: Dan Schieler [EMAIL PROTECTED] To: elecraft@mailman.qth.net Sent: Friday, November 05, 2004 8:11 PM Subject: [Elecraft] Spectrogram help I must be doing something wrong. Have my BFO settings exactly as specified in the K2 manual on CW. Using the noise gen from Elecraft. However, during the BFO settings per the K2 manual, FL2-FL4 at the BFO settings they specify results in almost no audio coming from the speaker using the N-gen. Then, when I go to spectrogram, my entire curve for FL1 is to the right of 600Hz on this display and no matter what I do with the vfo knob, there is no shifting of the curve to speak of and just changes in amplitude. On FL2-FL4, there is no amplitude at all but I can then adjust the VFO and see/hear the Ngen signals coming thru but the entire curve is still to the right of 600Hz. Running spectrogram off the headphone jack to my sound card. During operation, my CW mode audio level is considerably below the LSB or USB level and my receive CW signals seem to turn to clicks at audio freq below 800Hz or so.what have I missed? Thx K5GUS Dan ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spectrogram help
Dan, The BFO settings in the manual are only a starting point. You have to refine them for your particular K2. Since you already have the N-gen and Spectrogram, you have all the tools you need for the task. For detailed instructions on setting your filter/BFOs, look at my website www.qsl.net/w3fpr article on K2 Dial Calibration - the CAL PLL procedures are detailed in Step 3 of that article. Links are provided for additional information if you need it. 73, Don W3FPR - Original Message - I must be doing something wrong. Have my BFO settings exactly as specified in the K2 manual on CW. Using the noise gen from Elecraft. However, during the BFO settings per the K2 manual, FL2-FL4 at the BFO settings they specify results in almost no audio coming from the speaker using the N-gen. Then, when I go to spectrogram, my entire curve for FL1 is to the right of 600Hz on this display and no matter what I do with the vfo knob, there is no shifting of the curve to speak of and just changes in amplitude. On FL2-FL4, there is no amplitude at all but I can then adjust the VFO and see/hear the Ngen signals coming thru but the entire curve is still to the right of 600Hz. Running spectrogram off the headphone jack to my sound card. During operation, my CW mode audio level is considerably below the LSB or USB level and my receive CW signals seem to turn to clicks at audio freq below 800Hz or so.what have I missed? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com