Re: [Emc-users] Another 5i25-7i76 question - spindle encoder this time.
On Wed, 1 Oct 2014, John Alexander Stewart wrote: > Date: Wed, 1 Oct 2014 22:14:16 -0400 > From: John Alexander Stewart > Reply-To: "Enhanced Machine Controller (EMC)" > > To: "Enhanced Machine Controller (EMC)" > Subject: [Emc-users] Another 5i25-7i76 question - spindle encoder this time. > > My 7i76 mill is working very well. > > The last setup before I put everything in its place is to get Andy Pugh's > automatic spindle software gearing to work. > > I have a spindle encoder, that is not-differential, and does not have an > index. 16 pulses per rev. > > I have it wired such that the 3 jumpers (W4, W5, W6) are in the left hand > position (closest to the 25 pin connector), and a wire goes to the ENCA+, > TB3, pin 7. This should put it in TTL mode, with the pulse train going to > ENCA+. > > Between pin 7 and pin 1 (gnd) when spinning the spindle manually, I get > between 0.8v and 5.65v on my digital voltmeter. > > Input power, 7i76 manual, page 49, says Input Common Mode Range -7 to +12 > volts. Input TTL threshold is 1.4 to 1.8v. > > I HAVE NOT connected (or jumpered) any other input wires for this encoder - > they are left floating. > > The encoder.00.counter-mode is set to 1 > encoder.00.filter set to 1 > encoder.00.index-invert set to 0, index-mask-invert to 0, latch-enable to 0 > encoder.00.scale set to 16 > > I see nothing - no counts, no "action" on the input. > > I also don't have much luck googling this stuff - maybe I need to practice > more. > > Does the above look reasonable? Should I jumper the ENCB, IDX, lines > somewhere? > > Yours confusingly, > John A. Stewart. This sounds familiar, can you check the the countermode is indeed set true? I think pncconf sets the counter mode it two places so you think you have counter mode set true but its not... > -- > Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer > Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports > Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper > Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer > http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your (")_(") signature to help him gain world domination. -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] Another 5i25-7i76 question - spindle encoder this time.
My 7i76 mill is working very well. The last setup before I put everything in its place is to get Andy Pugh's automatic spindle software gearing to work. I have a spindle encoder, that is not-differential, and does not have an index. 16 pulses per rev. I have it wired such that the 3 jumpers (W4, W5, W6) are in the left hand position (closest to the 25 pin connector), and a wire goes to the ENCA+, TB3, pin 7. This should put it in TTL mode, with the pulse train going to ENCA+. Between pin 7 and pin 1 (gnd) when spinning the spindle manually, I get between 0.8v and 5.65v on my digital voltmeter. Input power, 7i76 manual, page 49, says Input Common Mode Range -7 to +12 volts. Input TTL threshold is 1.4 to 1.8v. I HAVE NOT connected (or jumpered) any other input wires for this encoder - they are left floating. The encoder.00.counter-mode is set to 1 encoder.00.filter set to 1 encoder.00.index-invert set to 0, index-mask-invert to 0, latch-enable to 0 encoder.00.scale set to 16 I see nothing - no counts, no "action" on the input. I also don't have much luck googling this stuff - maybe I need to practice more. Does the above look reasonable? Should I jumper the ENCB, IDX, lines somewhere? Yours confusingly, John A. Stewart. -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Spindle Synchronized Motion Problem
I think this thread has grown in scope. I did use Halscope to look at the signals as suggested by Chris Radek and it showed a discontinuity in the encoder velocity. This led me to looking at the regularity of the index pulse which was found to be flawed. I didn't take any pictures of the Halscope measurements so I assume the post you saw was from another user's problem. In any case, I can't expect the tapping cycle to be reliable if the signals from my encoder are not being accurately relayed to the computer. I'll focus on getting that right before I look any further into LinuxCNC configuration. Thanks David Nicholls -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] CNC Fest in Houston
On 10/01/2014 08:56 AM, Sebastian Kuzminsky wrote: > On 10/01/2014 04:38 AM, John Thornton wrote: >> When is the fest? > http://wiki.linuxcnc.org/cgi-bin/wiki.pl?LinuxCNC_Fest_2014 > > WOW, how did I miss this entry on the Wiki? (Fortunately, I did know about it, but had to dig through old emails for info.) Anyway, if anyone near Missouri wants to ride with me, that should be possible. Jon -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] CNC Fest in Houston
On 10/01/2014 04:38 AM, John Thornton wrote: > When is the fest? http://wiki.linuxcnc.org/cgi-bin/wiki.pl?LinuxCNC_Fest_2014 I hope you can make it! -- Sebastian Kuzminsky -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] CNC Fest in Houston
I think I saw Saturday 10/18 with a possibility of getting together the evening of the 17th too. What is the address? Where are most folks staying? On Wed, Oct 1, 2014 at 5:38 AM, John Thornton wrote: > When is the fest? > > JT > > On 9/30/2014 11:51 PM, Jon Elson wrote: >> John, >> >> Are you going to the fest in Houston? I am looking for >> another driver. >> My wife is dithering on going, and I am guessing she >> probably won't >> want to leave nobody keeping an eye on the kids for that long. >> >> It appears to be about 13 hours from St. Louis. That's doable >> in one shot for two drivers, but way beyond my capacity for >> punishment all by myself. >> >> Jon >> >> -- >> Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer >> Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports >> Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper >> Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer >> http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk >> ___ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > -- > Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer > Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports > Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper > Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer > http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users -- ><> ... Jack "Whatever you do, work at it with all your heart"... Colossians 3:23 "If you are not part of the solution, you are part of the precipitate" - Henry J. Tillman "Anyone who has never made a mistake, has never tried anything new." - Albert Einstein "You don't manage people; you manage things. You lead people." - Admiral Grace Hopper, USN "a nanosecond is the time it takes electrons to propigate 11.8 inches" - " - http://youtu.be/JEpsKnWZrJ8 "Life is complex: it has a real part and an imaginary part." - Martin Terma -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] CNC Fest in Houston
When is the fest? JT On 9/30/2014 11:51 PM, Jon Elson wrote: > John, > > Are you going to the fest in Houston? I am looking for > another driver. > My wife is dithering on going, and I am guessing she > probably won't > want to leave nobody keeping an eye on the kids for that long. > > It appears to be about 13 hours from St. Louis. That's doable > in one shot for two drivers, but way beyond my capacity for > punishment all by myself. > > Jon > > -- > Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer > Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports > Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper > Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer > http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users -- Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users