Re: [Fwd: Config Network Setting]
Craig White wrote: On Sun, 2008-09-28 at 22:53 +0800, [EMAIL PROTECTED] wrote: Dear All, I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? looks OK except that I would recommend that you use a FQDN in /etc/sysconfig/network and not just a name... i.e. srv1.mynetwork.com obviously /dev/eth0 is not going to be loaded at boot time - but that may be your intentions. BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? shouldn't be any difference as either should modify the same /etc/sysconfig/network-scripts/ifcfg-ethX file system-config-network does have the ability to also edit your 'hosts' file (/etc/hosts), you dns resolution configuration (/etc/resolv.conf) at one session. Craig Hello, How can we enable and verify the Network Interface working with full duplex mode ? Thanks Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Aldo Foot wrote: On Sun, Sep 28, 2008 at 7:53 AM, [EMAIL PROTECTED] wrote: Dear All, I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? The system-config-network is just a GUI to make it easier to configure the devices. What kind of network devices do you have? are they PCI cards or attached to the motherboard? ~af /etc/modprobe.conf : aliases eth0 8139too aliases eth1 r8169 For 8139too driver, it is a network interface PCI card ( 10/100M half duplex )... For r8169 driver, it is attached to the motherboard ( ASUS Desktop Barebone : P2-P5945GCX, 1.0G )... The System is FC8... So, any more help for me ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
[EMAIL PROTECTED] wrote: I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? looks OK except that I would recommend that you use a FQDN in /etc/sysconfig/network and not just a name... i.e. srv1.mynetwork.com obviously /dev/eth0 is not going to be loaded at boot time - but that may be your intentions. BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? shouldn't be any difference as either should modify the same /etc/sysconfig/network-scripts/ifcfg-ethX file system-config-network does have the ability to also edit your 'hosts' file (/etc/hosts), you dns resolution configuration (/etc/resolv.conf) at one session. Craig Hello, How can we enable and verify the Network Interface working with full duplex mode ? Run ethtool to display the current settings. You can also include ETHTOOL_OPTS in your ifcfg-ethX file to force a setting but if the other end of the connection is set to autonegotiate both ends must negotiate - and current equipment usually gets it right. -- Les Mikesell [EMAIL PROTECTED] -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Les Mikesell wrote: [EMAIL PROTECTED] wrote: I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? looks OK except that I would recommend that you use a FQDN in /etc/sysconfig/network and not just a name... i.e. srv1.mynetwork.com obviously /dev/eth0 is not going to be loaded at boot time - but that may be your intentions. BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? shouldn't be any difference as either should modify the same /etc/sysconfig/network-scripts/ifcfg-ethX file system-config-network does have the ability to also edit your 'hosts' file (/etc/hosts), you dns resolution configuration (/etc/resolv.conf) at one session. Craig Hello, How can we enable and verify the Network Interface working with full duplex mode ? Run ethtool to display the current settings. You can also include ETHTOOL_OPTS in your ifcfg-ethX file to force a setting but if the other end of the connection is set to autonegotiate both ends must negotiate - and current equipment usually gets it right. Hello, How to enable the NIC with full duplex mode by using option ETHTOOL_OPTS in ifcfg-ethx file ? Is there sample config for reference ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Les Mikesell wrote: [EMAIL PROTECTED] wrote: I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? looks OK except that I would recommend that you use a FQDN in /etc/sysconfig/network and not just a name... i.e. srv1.mynetwork.com obviously /dev/eth0 is not going to be loaded at boot time - but that may be your intentions. BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? shouldn't be any difference as either should modify the same /etc/sysconfig/network-scripts/ifcfg-ethX file system-config-network does have the ability to also edit your 'hosts' file (/etc/hosts), you dns resolution configuration (/etc/resolv.conf) at one session. Craig Hello, How can we enable and verify the Network Interface working with full duplex mode ? Run ethtool to display the current settings. You can also include ETHTOOL_OPTS in your ifcfg-ethX file to force a setting but if the other end of the connection is set to autonegotiate both ends must negotiate - and current equipment usually gets it right. Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Mon, Sep 29, 2008 at 7:05 AM, [EMAIL PROTECTED] wrote: Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? In a previous reply you said: For 8139too driver, it is a network interface PCI card For r8169 driver, it is attached to the motherboard I have seen before that the OS will change the device if you have a PCI and a built-in NIC. If you unplug the PCI NIC, the built-in NIC becomes eth0. With the PCI NIC plugged in, the built-in NIC becomes eth1 and the PCI becomes eth0. Try unplugging the PCI NIC to check whether this is the case with your machine; take note of the MAC address with the ifconfig command to track which one is which. I have not understood why this happens though. Maybe someone can shed some light here. ~af -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Aldo Foot wrote: On Mon, Sep 29, 2008 at 7:05 AM, [EMAIL PROTECTED] wrote: Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? In a previous reply you said: For 8139too driver, it is a network interface PCI card For r8169 driver, it is attached to the motherboard I have seen before that the OS will change the device if you have a PCI and a built-in NIC. If you unplug the PCI NIC, the built-in NIC becomes eth0. With the PCI NIC plugged in, the built-in NIC becomes eth1 and the PCI becomes eth0. Try unplugging the PCI NIC to check whether this is the case with your machine; take note of the MAC address with the ifconfig command to track which one is which. I have not understood why this happens though. Maybe someone can shed some light here. ~af Hello, Is this problem in FC8 System only ? So, have you tried to find doc though the net ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Mon, Sep 29, 2008 at 9:46 AM, [EMAIL PROTECTED] wrote: Aldo Foot wrote: On Mon, Sep 29, 2008 at 7:05 AM, [EMAIL PROTECTED] wrote: Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? In a previous reply you said: For 8139too driver, it is a network interface PCI card For r8169 driver, it is attached to the motherboard I have seen before that the OS will change the device if you have a PCI and a built-in NIC. If you unplug the PCI NIC, the built-in NIC becomes eth0. With the PCI NIC plugged in, the built-in NIC becomes eth1 and the PCI becomes eth0. Try unplugging the PCI NIC to check whether this is the case with your machine; take note of the MAC address with the ifconfig command to track which one is which. I have not understood why this happens though. Maybe someone can shed some light here. ~af Hello, Is this problem in FC8 System only ? So, have you tried to find doc though the net ? disclamer I have not done this and I don't know whether that is accurate. /disclaimer I did some reading. It appears that udev does the device switching. But if desired, the devices can be tied to a specific mac address. See this old thread --notice what they say about /etc/modprobe.conf. http://www.redhat.com/archives/k12osn/2005-September/msg00354.html Read this Debian related page: http://www.debianhelp.co.uk/udev.htm I don't now whether the problem is with F8 only. I haven't tried all the flavors. ~af -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Aldo Foot wrote: On Mon, Sep 29, 2008 at 9:46 AM, [EMAIL PROTECTED] wrote: Aldo Foot wrote: On Mon, Sep 29, 2008 at 7:05 AM, [EMAIL PROTECTED] wrote: Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? In a previous reply you said: For 8139too driver, it is a network interface PCI card For r8169 driver, it is attached to the motherboard I have seen before that the OS will change the device if you have a PCI and a built-in NIC. If you unplug the PCI NIC, the built-in NIC becomes eth0. With the PCI NIC plugged in, the built-in NIC becomes eth1 and the PCI becomes eth0. Try unplugging the PCI NIC to check whether this is the case with your machine; take note of the MAC address with the ifconfig command to track which one is which. I have not understood why this happens though. Maybe someone can shed some light here. ~af Hello, Is this problem in FC8 System only ? So, have you tried to find doc though the net ? disclamer I have not done this and I don't know whether that is accurate. /disclaimer I did some reading. It appears that udev does the device switching. But if desired, the devices can be tied to a specific mac address. See this old thread --notice what they say about /etc/modprobe.conf. http://www.redhat.com/archives/k12osn/2005-September/msg00354.html Read this Debian related page: http://www.debianhelp.co.uk/udev.htm I don't now whether the problem is with F8 only. I haven't tried all the flavors. ~af Hello, How can we disable the udev for switching the device with FC8 System ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
Aldo Foot wrote: On Mon, Sep 29, 2008 at 9:46 AM, [EMAIL PROTECTED] wrote: Aldo Foot wrote: On Mon, Sep 29, 2008 at 7:05 AM, [EMAIL PROTECTED] wrote: Dear All, I just found a message for /var/log/messages : kernel : udev: renamed network interface eth0 to eth1 So, how to solve this problem ? In a previous reply you said: For 8139too driver, it is a network interface PCI card For r8169 driver, it is attached to the motherboard I have seen before that the OS will change the device if you have a PCI and a built-in NIC. If you unplug the PCI NIC, the built-in NIC becomes eth0. With the PCI NIC plugged in, the built-in NIC becomes eth1 and the PCI becomes eth0. Try unplugging the PCI NIC to check whether this is the case with your machine; take note of the MAC address with the ifconfig command to track which one is which. I have not understood why this happens though. Maybe someone can shed some light here. ~af Hello, Is this problem in FC8 System only ? So, have you tried to find doc though the net ? disclamer I have not done this and I don't know whether that is accurate. /disclaimer I did some reading. It appears that udev does the device switching. But if desired, the devices can be tied to a specific mac address. See this old thread --notice what they say about /etc/modprobe.conf. http://www.redhat.com/archives/k12osn/2005-September/msg00354.html Read this Debian related page: http://www.debianhelp.co.uk/udev.htm I don't now whether the problem is with F8 only. I haven't tried all the flavors. ~af Hello, If disbale the onboard lan and install another INC, then, is there still the problem ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Sun, 2008-09-28 at 22:53 +0800, [EMAIL PROTECTED] wrote: Dear All, I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? looks OK except that I would recommend that you use a FQDN in /etc/sysconfig/network and not just a name... i.e. srv1.mynetwork.com obviously /dev/eth0 is not going to be loaded at boot time - but that may be your intentions. BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? shouldn't be any difference as either should modify the same /etc/sysconfig/network-scripts/ifcfg-ethX file system-config-network does have the ability to also edit your 'hosts' file (/etc/hosts), you dns resolution configuration (/etc/resolv.conf) at one session. Craig -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Sun, Sep 28, 2008 at 7:53 AM, [EMAIL PROTECTED] wrote: Dear All, I just have the problem of Destination Host Unreachable from eth1 ( ping to other same network segment internal machine ) as the following setting : [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=no [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static BROADCAST=192.168.0.255 IPADDR=192.168.0.254 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [EMAIL PROTECTED] network-scripts]# [EMAIL PROTECTED] network-scripts]# cat ../network NETWORKING=yes HOSTNAME=svr1 [EMAIL PROTECTED] network-scripts]# So, what is the problem of the current setting ? BTW, what different between modify ifcfg-eth? and running the tools of system-config-network ? The system-config-network is just a GUI to make it easier to configure the devices. What kind of network devices do you have? are they PCI cards or attached to the motherboard? ~af -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
[Fwd: Config Network Setting]
Dear All, After modify the config files, I can't restart the network controll by using /etc/rc.d/init.d/network restart... Thanks ! Edward. Original Message Subject:Config Network Setting Date: Sat, 27 Sep 2008 14:43:32 +0800 From: [EMAIL PROTECTED] Reply-To: Community assistance, encouragement, and advice for using Fedora. fedora-list@redhat.com To: fedora-list@redhat.com fedora-list@redhat.com Dear All, Mine is FC8 System... So, if I want to modify the config of controller card, then I need to edit the following files ? /etc/sysconifg/network-scripts/ifcfg-eth? /etc/modprobe.conf And what else other profile also need to be modified ? Thanks ! Edward. -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines __ NOD32 3475 (20080926) Information __ This message was checked by NOD32 antivirus system. http://www.nod32.com.hk -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Sat, 2008-09-27 at 15:08 +0800, [EMAIL PROTECTED] wrote: Dear All, After modify the config files, I can't restart the network controll by using /etc/rc.d/init.d/network restart... Thanks ! Edward. Original Message Subject: Config Network Setting Date: Sat, 27 Sep 2008 14:43:32 +0800 From: [EMAIL PROTECTED] Reply-To: Community assistance, encouragement, and advice for using Fedora. fedora-list@redhat.com To: fedora-list@redhat.com fedora-list@redhat.com Dear All, Mine is FC8 System... So, if I want to modify the config of controller card, then I need to edit the following files ? /etc/sysconifg/network-scripts/ifcfg-eth? /etc/modprobe.conf And what else other profile also need to be modified ? crystal ball cloudy... why did you modify /etc/modprobe.conf? what is error in /var/log/messages? what is output of... cat /etc/sysconfig/network-scripts/ifcfg-eth* cat /etc/modprobe.conf Craig -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
Re: [Fwd: Config Network Setting]
On Sat, Sep 27, 2008 at 12:08 AM, [EMAIL PROTECTED] wrote: Mine is FC8 System... So, if I want to modify the config of controller card, then I need to edit the following files ? /etc/sysconifg/network-scripts/ifcfg-eth? /etc/modprobe.conf And what else other profile also need to be modified ? /etc/modprobe.conf has nothing to do with your network settings. First --- look here http://docs.fedoraproject.org/install-guide/f8/en_US/ch-networkconfig.html Then --- As root launch /usr/sbin/system-config-network and configure your netcard, which by default is eth0. ~af -- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
