[Flexradio] Flex 5000
I just installed new console,firmware and firewire driver. Main receiver works as normal. 2nd Receiver comes up on the screen but no signals present. I have in the ant menu the rx1 tap checked. Firmware 1.2.1.10. Before installation of new software and firmware all worked as normal. What am I missing? Thanks for the help in advance. Dave ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Announcing an important new firmware/driver/PowerSDRrelease
One clarification: The new PowerSDR release is v1.14.0. The second reference to PowerSDR v1.12.2 is an error. Gerald Youngblood, K5SDR President FlexRadio Systems 13091 Pond Springs Rd. #250 Austin, TX 78729 Phone: 512-535-4713 -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Gerald Youngblood Sent: Tuesday, September 02, 2008 4:18 PM To: FlexRadio List Subject: [Flexradio] Announcing an important new firmware/driver/PowerSDRrelease Dear FlexRadio customers, We are pleased to announce an important new Official Release of FLEX-5000(TM) firmware (v1.2.1.10), FLEX-5000 driver (v3.2.0.1556) and PowerSDR(TM) (v1.14.0) that are recommended for all customers. While there are a number of performance and feature improvements contained in this release, I would like to point out a few of the most important ones: 1. Improved CW keying (FLEX-5000 only) - We have incorporated an enhanced debounce algorithm in the firmware that eliminates key bounce problems incurred when using some types of paddles, including the Begali. Our beta testers report excellent results at very high keying rates using all of the reported problem paddles. 2. Lower latency and CPU loading (FLEX-5000 only) - The new firmware and drivers result in lower latency for all operating modes. We have also seen a significant reduction in CPU loading, which means that the software will perform better on lower end machines than in the past. With the lower CPU loading, we have found that more aggressive buffer and driver mode settings have been possible further reducing latency. 3. Vista 64-bit support (FLEX-5000 only) - The new drivers support 64-bit Vista but we consider this capability to be in Beta test. Since we have had limited testing in this area, we would appreciate direct feedback from customers who can test this configuration. 4. New driver interface with built in DPC monitor (FLEX-5000 only) - The user interface and setup automation for the FLEX-5000 has been improved. A built in DPC monitor is now included, which helps in isolating latency problems caused by other devices and/or software found on an individual PC configuration. 5. New display modes (FLEX-5000 & SDR-1000) - We have added PanaFall and PanaScope modes that allow the Panadapter over Waterfall and Panadapater over Oscilloscope with a single receiver. 6. Automated local EEPROM backup (FLEX-5000 only) - PowerSDR will now create a backup of the radio's EEPROM calibration data to the working directory the first time the software is loaded. 7. SO2R transmit frequency selection controls (FLEX-5000 only) - Controls have been added on the VFOA and VFOB to allow simple switching of the transmit frequency when RX2 is installed. 8. Simplified "Default" TX Profile settings (FLEX-5000 & SDR-1000) - We now provide two standard default settings for voice modes, which are optimized for normal voice communications and DX operations respectively. For a full list of enhancements please read the PowerSDR v1.12.2 - Release Notes at: http://kc.flex-radio.com/KnowledgebaseArticle50344.aspx You may download all of the files directly from the link on the FlexRadio Systems home page at www.flex-radio.com. IMPORTANT: Please read the following Knowledge Base article before installing: FLEX-5000 Firmware 1.2.1.10 Upgrade Procedure http://kc.flex-radio.com/KnowledgebaseArticle50339.aspx NOTE: To use the new PowerSDR v1.12.2, FLEX-5000 owners must upgrade both the FLEX-5000 driver and firmware to the latest release referenced above. If you have problems with installation of the new release, please contact customer support at [EMAIL PROTECTED] or call 512-250-8595. We would like to thank those of you who have contributed to coding, bug reporting, beta testing for this important release. Regards, Gerald Gerald Youngblood, K5SDR President FlexRadio Systems 13091 Pond Springs Rd. #250 Austin, TX 78729 Phone: 512-535-4713 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] Announcing an important new firmware/driver/PowerSDR release
Dear FlexRadio customers, We are pleased to announce an important new Official Release of FLEX-5000(TM) firmware (v1.2.1.10), FLEX-5000 driver (v3.2.0.1556) and PowerSDR(TM) (v1.14.0) that are recommended for all customers. While there are a number of performance and feature improvements contained in this release, I would like to point out a few of the most important ones: 1. Improved CW keying (FLEX-5000 only) - We have incorporated an enhanced debounce algorithm in the firmware that eliminates key bounce problems incurred when using some types of paddles, including the Begali. Our beta testers report excellent results at very high keying rates using all of the reported problem paddles. 2. Lower latency and CPU loading (FLEX-5000 only) - The new firmware and drivers result in lower latency for all operating modes. We have also seen a significant reduction in CPU loading, which means that the software will perform better on lower end machines than in the past. With the lower CPU loading, we have found that more aggressive buffer and driver mode settings have been possible further reducing latency. 3. Vista 64-bit support (FLEX-5000 only) - The new drivers support 64-bit Vista but we consider this capability to be in Beta test. Since we have had limited testing in this area, we would appreciate direct feedback from customers who can test this configuration. 4. New driver interface with built in DPC monitor (FLEX-5000 only) - The user interface and setup automation for the FLEX-5000 has been improved. A built in DPC monitor is now included, which helps in isolating latency problems caused by other devices and/or software found on an individual PC configuration. 5. New display modes (FLEX-5000 & SDR-1000) - We have added PanaFall and PanaScope modes that allow the Panadapter over Waterfall and Panadapater over Oscilloscope with a single receiver. 6. Automated local EEPROM backup (FLEX-5000 only) - PowerSDR will now create a backup of the radio's EEPROM calibration data to the working directory the first time the software is loaded. 7. SO2R transmit frequency selection controls (FLEX-5000 only) - Controls have been added on the VFOA and VFOB to allow simple switching of the transmit frequency when RX2 is installed. 8. Simplified "Default" TX Profile settings (FLEX-5000 & SDR-1000) - We now provide two standard default settings for voice modes, which are optimized for normal voice communications and DX operations respectively. For a full list of enhancements please read the PowerSDR v1.12.2 - Release Notes at: http://kc.flex-radio.com/KnowledgebaseArticle50344.aspx You may download all of the files directly from the link on the FlexRadio Systems home page at www.flex-radio.com. IMPORTANT: Please read the following Knowledge Base article before installing: FLEX-5000 Firmware 1.2.1.10 Upgrade Procedure http://kc.flex-radio.com/KnowledgebaseArticle50339.aspx NOTE: To use the new PowerSDR v1.12.2, FLEX-5000 owners must upgrade both the FLEX-5000 driver and firmware to the latest release referenced above. If you have problems with installation of the new release, please contact customer support at [EMAIL PROTECTED] or call 512-250-8595. We would like to thank those of you who have contributed to coding, bug reporting, beta testing for this important release. Regards, Gerald Gerald Youngblood, K5SDR President FlexRadio Systems 13091 Pond Springs Rd. #250 Austin, TX 78729 Phone: 512-535-4713 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Using MMTTY and APRS with two Sound Cards(HELP)
What is your Windows default sound card? I should not be either of the VAC channels. -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Howard Benjamin Sent: Tuesday, September 02, 2008 3:06 AM To: flexradio@flex-radio.biz Subject: [Flexradio] Using MMTTY and APRS with two Sound Cards(HELP) I am using the FlexRadio 1K with the Delta M44 sound card and operate MMTTY sucessfully via The VAC software. However, I am having probems in connecting my external VHF radioAPRS to the built in Realtec soundcard. I have tried the control panel sounds and audio devices but can only get either the M44 or realtec soundcards to work independently. The probem is to get the MMTTY to work via the VAC from the Flex 1K and to get the APRS audio from my VHF receiver to connect via the mic or line jack on the PC to the realtec or even to the Delta M44. Can anyone please help? 73 de Howard 5B4AHX ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
Re: [Flexradio] Using MMTTY and APRS with two Sound Cards(HELP)
I use direct cables for everything - had major problems with VAC in the beginning, decided to just wire them up directly. I ran cables between the cards, replacing VAC. Works for me (and better performance than VAC). Jerry W4UK At 03:06 AM 9/2/2008, Howard Benjamin wrote: >I am using the FlexRadio 1K with the Delta M44 sound card and operate MMTTY >sucessfully via The VAC software. However, I am having probems in connecting >my external VHF radioAPRS to the built in Realtec soundcard. I have tried >the control panel sounds and audio devices but can only get either the M44 >or realtec soundcards to work independently. > >The probem is to get the MMTTY to work via the VAC from the Flex 1K and to >get the APRS audio from my VHF receiver to connect via the mic or line jack >on the PC to the realtec or even to the Delta M44. > >Can anyone please help? > >73 de Howard 5B4AHX > > > >___ >FlexRadio Systems Mailing List >FlexRadio@flex-radio.biz >http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz >Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ >Knowledge Base: http://kb.flex-radio.com/ Homepage: >http://www.flex-radio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] Help wanted.
Flexers: Looking for FLEX-5000 owner with good people skills to help man booth at Pacificon Oct 17-19. Compensation will be provided. If you are interested, please call or email John or Matt at 512 535-4713. John P. Basilotto W5GI Chief Operating Officer Marketing and Sales Office 512 535-5266 Fax 512-233-5143 13901 Pond Springs Rd Suite 250 Austin, TX 78729 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
[Flexradio] Using MMTTY and APRS with two Sound Cards(HELP)
I am using the FlexRadio 1K with the Delta M44 sound card and operate MMTTY sucessfully via The VAC software. However, I am having probems in connecting my external VHF radioAPRS to the built in Realtec soundcard. I have tried the control panel sounds and audio devices but can only get either the M44 or realtec soundcards to work independently. The probem is to get the MMTTY to work via the VAC from the Flex 1K and to get the APRS audio from my VHF receiver to connect via the mic or line jack on the PC to the realtec or even to the Delta M44. Can anyone please help? 73 de Howard 5B4AHX ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/