Re: [Flexradio] Parallel Port for F3K
Further, check where the headers go. I have a couple of boards that the header goes to chips that were not installed!! Absolutely. VERY common. You have to wonder why they went to all the trouble to engineer these ports and then make them unusable. There are lots of things that are engineered on mainboards and not used or where either the connectors or the circuitry is not populated. You're designing a main board, you need to have a Southbridge (equivalent) for the USB, SMBus, and other functionality you need, and the part either includes all the serial port logic in it already, or your Southbridge has a connector to a Super I/O chip that has serial and parallel port logic in it. You can't really buy a part that doesn't HAVE these things in it. So, you design your mainboard, you wire-up the traces just in case -- There's no cost to put the traces down. And you can always not populate the socket. And the socket can be useful for various OEMs/IHVs during debugging. So, why not populate them? Because it saves some tenths of a cent, and Microsoft doesn't require it as part of getting the Designed for Windows logo. In fact, Microsoft have been actively DIScouraging parallel and serial ports on systems for years... it's called Legacy Free PC. The general belief is that using these ports tend to confuse the technologically naïve. Seriously. OTOH, back in the days of the IBM Thinkpad, I seem to recall a story about IBM removing the printer port (parallel port) from one of their Thinkpad models, and corporate types howling in protest. How would they print their Powerpoint slides? The parallel port quickly returned on subsequent models. Peter K1PGV ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] FlexRadio Digest, Vol 74, Issue 19
VOX??? I have been playing with SSB on my FLEX 1500 but can't find in the manual or any menu a VOX option. Anyone have any ideas on this or options. I use a boom Goldline Heil Mic and PTT operating is not handy and clicking MOX on and off not happy way to operate either. Carl/K5HK Reno NV On Sun, Jun 19, 2011 at 10:00 AM, flexradio-requ...@flex-radio.biz wrote: Send FlexRadio mailing list submissions to flexradio@flex-radio.biz To subscribe or unsubscribe via the World Wide Web, visit http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz or, via email, send a message with subject or body 'help' to flexradio-requ...@flex-radio.biz You can reach the person managing the list at flexradio-ow...@flex-radio.biz When replying, please edit your Subject line so it is more specific than Re: Contents of FlexRadio digest... Today's Topics: 1. An off-topic inquiry (William H. Fite) 2. 6m FM - deadband? (Michael Ruttenberg) 3. Firewire to USB (Freek Witte) 4. Re: 6m FM - deadband? (Alfred Green) 5. Re: Firewire to USB (Neal Campbell) -- Message: 1 Date: Sat, 18 Jun 2011 15:32:58 -0400 From: William H. Fite omni...@gmail.com To: FlexRadio Reflector flexradio@flex-radio.biz, flexe...@flex-radio.biz Subject: [Flexradio] An off-topic inquiry Message-ID: BANLkTinY+AFcg7gXvtrbDwHW9mcTB2=c...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Please forgive a brief foray off topic. If anyone out there has experience with Emtron amplifiers, built in Australia, would you please contact me off line? Thanks and we now resume our regular programming. Bill -- Message: 2 Date: Sun, 19 Jun 2011 11:21:38 +0100 From: Michael Ruttenberg mjruttenb...@gmail.com To: flexradio@flex-radio.biz Subject: [Flexradio] 6m FM - deadband? Message-ID: BANLkTinv34oFW=vadhhzu-cu9fmrjdm...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Hi all I'm on 6m (51.530Mhz) with a Flex 3000 and I am seeing 6m deadband below the ferquency output on VFO A. What does this mean and how do I make it use NFM. This is a working frequency in the UK (bandplan 50-52Mhz). TIA Mike G7TWC -- Message: 3 Date: Sun, 19 Jun 2011 16:05:56 +0200 (West-Europa (zomertijd)) From: Freek Witte freekwi...@zeelandnet.nl To: flexradio@flex-radio.biz Subject: [Flexradio] Firewire to USB Message-ID: 4DFE0244.03.02688@PA0PAF-DESKTOP Content-Type: Text/Plain; charset=iso-8859-1 Has anyone ever tried this ?thing? to connect a Flex 5000 to a USB port? http://www.pixela.co.jp/en/products/tv_capture/pix_uvcd_u1w/spec.html 73, Fred PA0PAF -- Message: 4 Date: Sun, 19 Jun 2011 07:26:18 -0700 From: Alfred Green n...@cox.net To: flexradio@flex-radio.biz Subject: Re: [Flexradio] 6m FM - deadband? Message-ID: 4dfe070a.2050...@cox.net Content-Type: text/plain; charset=ISO-8859-1; format=flowed On 6/19/2011 3:21 AM, Michael Ruttenberg wrote: Hi all I'm on 6m (51.530Mhz) with a Flex 3000 and I am seeing 6m deadband below the ferquency output on VFO A. What does this mean and how do I make it use NFM. This is a working frequency in the UK (bandplan 50-52Mhz). I have never tried operating in that part of the band, but just tuning there now it says the same thing as you see. However, it looks like just an info text, as there doesn't seem to be any restriction on transmitting there. I can get full power out on FMN across that band segment. As for the text, I imagine it may have something to do with a guard-band between repeater in/out and simplex frequencies. I am not familiar with the US bandplan in that frequency range. The text can be modified by editing the database. GL 73, Alf NU8I Scottsdale AZ DM43an -- Message: 5 Date: Sun, 19 Jun 2011 11:58:42 -0400 From: Neal Campbell abrohamn...@gmail.com To: Freek Witte freekwi...@zeelandnet.nl Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] Firewire to USB Message-ID: banlktimacyesnj4a2aaibzoyawvutnn...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Hi Fred It isn't compatible. Wish it was though! 73 Neal On Sun, Jun 19, 2011 at 10:05 AM, Freek Witte freekwi...@zeelandnet.nl wrote: Has anyone ever tried this ?thing? to connect a Flex 5000 to a USB port? http://www.pixela.co.jp/en/products/tv_capture/pix_uvcd_u1w/spec.html 73, Fred PA0PAF ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- Abroham Neal Software
Re: [Flexradio] FlexRadio Digest, Vol 74, Issue 19
VOX is not a feature of the FLEX-1500 See the Feature Matrix for the features supported by radio type http://www.flexradio.com/Products.aspx?topic=SDR_Feature_Matrix You can connect a hand or footswitch to the FlexWire port for an alternate method of keying the radio. -Tim -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Carl Young Sent: Monday, June 20, 2011 12:43 PM To: flexradio@flex-radio.biz Subject: Re: [Flexradio] FlexRadio Digest, Vol 74, Issue 19 VOX??? I have been playing with SSB on my FLEX 1500 but can't find in the manual or any menu a VOX option. Anyone have any ideas on this or options. I use a boom Goldline Heil Mic and PTT operating is not handy and clicking MOX on and off not happy way to operate either. Carl/K5HK Reno NV On Sun, Jun 19, 2011 at 10:00 AM, flexradio-requ...@flex-radio.biz wrote: Send FlexRadio mailing list submissions to flexradio@flex-radio.biz To subscribe or unsubscribe via the World Wide Web, visit http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz or, via email, send a message with subject or body 'help' to flexradio-requ...@flex-radio.biz You can reach the person managing the list at flexradio-ow...@flex-radio.biz When replying, please edit your Subject line so it is more specific than Re: Contents of FlexRadio digest... Today's Topics: 1. An off-topic inquiry (William H. Fite) 2. 6m FM - deadband? (Michael Ruttenberg) 3. Firewire to USB (Freek Witte) 4. Re: 6m FM - deadband? (Alfred Green) 5. Re: Firewire to USB (Neal Campbell) -- Message: 1 Date: Sat, 18 Jun 2011 15:32:58 -0400 From: William H. Fite omni...@gmail.com To: FlexRadio Reflector flexradio@flex-radio.biz, flexe...@flex-radio.biz Subject: [Flexradio] An off-topic inquiry Message-ID: BANLkTinY+AFcg7gXvtrbDwHW9mcTB2=c...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Please forgive a brief foray off topic. If anyone out there has experience with Emtron amplifiers, built in Australia, would you please contact me off line? Thanks and we now resume our regular programming. Bill -- Message: 2 Date: Sun, 19 Jun 2011 11:21:38 +0100 From: Michael Ruttenberg mjruttenb...@gmail.com To: flexradio@flex-radio.biz Subject: [Flexradio] 6m FM - deadband? Message-ID: BANLkTinv34oFW=vadhhzu-cu9fmrjdm...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Hi all I'm on 6m (51.530Mhz) with a Flex 3000 and I am seeing 6m deadband below the ferquency output on VFO A. What does this mean and how do I make it use NFM. This is a working frequency in the UK (bandplan 50-52Mhz). TIA Mike G7TWC -- Message: 3 Date: Sun, 19 Jun 2011 16:05:56 +0200 (West-Europa (zomertijd)) From: Freek Witte freekwi...@zeelandnet.nl To: flexradio@flex-radio.biz Subject: [Flexradio] Firewire to USB Message-ID: 4DFE0244.03.02688@PA0PAF-DESKTOP Content-Type: Text/Plain; charset=iso-8859-1 Has anyone ever tried this ?thing? to connect a Flex 5000 to a USB port? http://www.pixela.co.jp/en/products/tv_capture/pix_uvcd_u1w/spec.html 73, Fred PA0PAF -- Message: 4 Date: Sun, 19 Jun 2011 07:26:18 -0700 From: Alfred Green n...@cox.net To: flexradio@flex-radio.biz Subject: Re: [Flexradio] 6m FM - deadband? Message-ID: 4dfe070a.2050...@cox.net Content-Type: text/plain; charset=ISO-8859-1; format=flowed On 6/19/2011 3:21 AM, Michael Ruttenberg wrote: Hi all I'm on 6m (51.530Mhz) with a Flex 3000 and I am seeing 6m deadband below the ferquency output on VFO A. What does this mean and how do I make it use NFM. This is a working frequency in the UK (bandplan 50-52Mhz). I have never tried operating in that part of the band, but just tuning there now it says the same thing as you see. However, it looks like just an info text, as there doesn't seem to be any restriction on transmitting there. I can get full power out on FMN across that band segment. As for the text, I imagine it may have something to do with a guard-band between repeater in/out and simplex frequencies. I am not familiar with the US bandplan in that frequency range. The text can be modified by editing the database. GL 73, Alf NU8I Scottsdale AZ DM43an -- Message: 5 Date: Sun, 19 Jun 2011 11:58:42 -0400 From: Neal Campbell abrohamn...@gmail.com To: Freek Witte freekwi...@zeelandnet.nl Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] Firewire to USB Message-ID: banlktimacyesnj4a2aaibzoyawvutnn...@mail.gmail.com Content-Type: text/plain; charset=ISO-8859-1 Hi Fred It isn't compatible. Wish it was though! 73 Neal On Sun, Jun 19, 2011 at 10:05 AM, Freek Witte freekwi...@zeelandnet.nl wrote: Has
[Flexradio] using the flex control
Iam running 2.0.22 on XP ,I gather that I need to run 2.1 or latter,to run the flex control. I don't see 2.1.2 on the web site to down load. I did receive a cd with sdr 2.1.2 RC3. My 1500 runs perfect with 2.0.22. I hesitate to down load another power sdr version,that I don't know anything about and get caught up in another rounds of bug fixs, when 2.0.22 works so good for my application. Is this the only way to run the new control? thanks dale wt4t ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] using the flex control
Hi Dale If you want PowerSDR to use the knob you will have to upgrade. However, you could probably use it via DDUtil and stick with 2.0.22 (I think??) If you normally run DDU then I would try that. 73 Neal On Mon, Jun 20, 2011 at 2:57 PM, y...@aol.com y...@aol.com wrote: Iam running 2.0.22 on XP ,I gather that I need to run 2.1 or latter,to run the flex control. I don't see 2.1.2 on the web site to down load. I did receive a cd with sdr 2.1.2 RC3. My 1500 runs perfect with 2.0.22. I hesitate to down load another power sdr version,that I don't know anything about and get caught up in another rounds of bug fixs, when 2.0.22 works so good for my application. Is this the only way to run the new control? thanks dale wt4t ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- Abroham Neal Software www.abrohamnealsoftware.com Work:(540) 645 5394 Mobile:(540) 645 8171 ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] Parallel Port for F3K
Thanks to all the suggestions. I will first check to see if there is a parallel port on the board, and, if not, will see about ordering another PP card. This may take me a month or so since I just broke my arm in a tractor accident and can only use one hand. Fortunately it is not the hand I use for keying! Thanks again for the help! Bill W4ISH On Jun 19, 2011, at 7:35 PM, William Evans wrote: My computer does not have a parallel port which I need to get the band information out to antenna and amplifier switches. I need ABCD info to come out of the computer when I use my 3K. Has anyone had any luck with this device?: http://www.piexx.com/index.php?main_page=indexcPath=12 I could purchase a parallel port card, but the last one I got did not work, so I am asking before purchasing anything this time. W4ISH Bill ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
[Flexradio] All was well Until
I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] All was well Until
The standard first step after such a major problem. Is Delete the database, and create a new one. That will 'probably' get you going. you will probably have to re-install VSPm first so you have some comports to put into the new database. It's been my experience that it's best to start with a new database. Install one program Check it out Then install the next. Good luck, we have all been dere done dat and have the gray hairs to prove it. On 6/20/11 8:41 PM, Gary Franklin wrote: I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- --- Adam's Rib: The original bone of contention. --- Bill H. in Chicagoland webcams at http://w9ol-towercam.webhop.org weather at http://hhweather.webhop.org live weathercam chat hhweather.chatango.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] All was well Until
Your situation may be different from mine, but I had a similar thing happen to me once. I had to uninstall everything related to the powersdr software and reinstall which took care of the problem. You may just want to do a data base reset first. After that there are those on this list that know better about the deeper aspects and can help you. Just hollar. I doubt that the box is the problem. Vic K4XTT On 6/20/2011 9:41 PM, Gary Franklin wrote: I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] All was well Until
or been there, done that, bought the t-shirt . as we say in Texas... 73, w5xz, dan --- On Tue, 6/21/11, Bill w...@billnjudy.com wrote: From: Bill w...@billnjudy.com Subject: Re: [Flexradio] All was well Until To: flexradio@flex-radio.biz Date: Tuesday, June 21, 2011, 1:56 AM The standard first step after such a major problem. Is Delete the database, and create a new one. That will 'probably' get you going. you will probably have to re-install VSPm first so you have some comports to put into the new database. It's been my experience that it's best to start with a new database. Install one program Check it out Then install the next. Good luck, we have all been dere done dat and have the gray hairs to prove it. On 6/20/11 8:41 PM, Gary Franklin wrote: I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- --- Adam's Rib: The original bone of contention. --- Bill H. in Chicagoland webcams at http://w9ol-towercam.webhop.org weather at http://hhweather.webhop.org live weathercam chat hhweather.chatango.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] All was well Until
with my bodynobody wants to see me in a TEE Shirt! On 6/20/11 9:08 PM, dan edwards wrote: or been there, done that, bought the t-shirt . as we say in Texas... 73, w5xz, dan --- On *Tue, 6/21/11, Bill /w...@billnjudy.com/* wrote: From: Bill w...@billnjudy.com Subject: Re: [Flexradio] All was well Until To: flexradio@flex-radio.biz Date: Tuesday, June 21, 2011, 1:56 AM The standard first step after such a major problem. Is Delete the database, and create a new one. That will 'probably' get you going. you will probably have to re-install VSPm first so you have some comports to put into the new database. It's been my experience that it's best to start with a new database. Install one program Check it out Then install the next. Good luck, we have all been dere done dat and have the gray hairs to prove it. On 6/20/11 8:41 PM, Gary Franklin wrote: I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz /mc/compose?to=FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- --- Adam's Rib: The original bone of contention. --- Bill H. in Chicagoland webcams at http://w9ol-towercam.webhop.org weather at http://hhweather.webhop.org live weathercam chat hhweather.chatango.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz /mc/compose?to=FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- --- Babies are a nice way to start people. --- Bill H. in Chicagoland webcams at http://w9ol-towercam.webhop.org weather at http://hhweather.webhop.org live weathercam chat hhweather.chatango.com ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/
Re: [Flexradio] All was well Until
Tim, I guess the next question maybe what caused the need to reset to factory defaults? The VAC and VSP Manager software seemed to setup as expected but it freaked out PowerSDR. Wondering if I got something out of order while setting up. Gary - Original Message - From: Tim Ellison To: Gary Franklin Sent: Monday, June 20, 2011 10:17 PM Subject: Re: [Flexradio] All was well Until Reset the radio back to factory defaults using the feature in the Setup form. -Tim On Mon, Jun 20, 2011 at 9:41 PM, Gary Franklin franklin6...@att.net wrote: I am running a Flex 5000 on Vista and everything was flawless until! I decided to setup for the digital modes. I downloaded VAC 4.09 and VSP Manager. Installation went according to instructions . I set them both up with no problem then I started Power SDR and it was all down hill from there Power SDR loads but even before I turn on the power the band selection switch pulses between 80 meters and WWV resulting in the frequency display flashing between WWV and 80 meters. The AGC and Drive slider controls also pulsate between half setting to full setting alternately. It gets better when I turn the power switch it really go bonkers! Starts scanning frequency, changes bands, etc. all on its own! Interestingly I have been able to get back to normal operation by energizing the MOX (transmit) as long as It happens in a ham band. This of course does not last... I can turn the power off but I cannot exit PowerSDR with out using the Task Manager to shut down. Reboot and power gives the same result. I uninstalled VAC and VSP Manager no change I suspect I need to deal with the BOX. Any suggestions before I go further. Thanks, Gary K8BKB ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ -- -Tim --- ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/