Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
i compiled the gentoo gaming kernel instead and was able to boot. what that was a few wasted days. andrew From: "a park" <[EMAIL PROTECTED]> Reply-To: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Subject: [gentoo-user] Kernel panic while booting a new Gentoo installation Date: Thu, 25 Sep 2003 12:39:16 -0400 I received the following message while booting with a kernel that I compiled during the installation of Gentoo 2: hub.c: USB hub found hub.c: 3 ports detected Detected usb-ohci hardware Scanning for hid... usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik ([EMAIL PROTECTED]) hid-core.c: USB HID support drivers Detected hid hardware Kernel panic: Attempted to kill init! I compiled the 2.4.20 kernel that is retreived from gentoo-sources. I used the genkernel command without the --config option. I emerged the following: nvidia-kernel, nforce-net, nforce-audio because I have the following hardware: Athlon XP 2200+, Gigabyte GA-7NNXP (nforce2), 256 MB RAM, 40 GB IDE Harddrive (i think it is 7200rpm), NVidia GeForce 4400, Logitech USB Mouse, cdrom, two additional IDE hard drives. I've looked around the web for some answers and most seem to focus on ACPI / APIC and disabling it. I don't mind disabling it as long as I don't see any performance degredation (which is kind of difficult to judge since my machine is not performing at all). There seems to be three places to disable it: the BIOS, the kernel and the boot command (pci=noacpi noapic) (could i place this in lilo.conf?). What would be the best way to determine if this is the problem? Which would be the best place to disable it at? Would this solve my problems? Here is one of the sources of information that I found on the net: http://www.burocrata.org/newwiki/NvidiaNforce Thank you in advance for any and all assistance. Andrew _ Get MSN 8 Dial-up Internet Service FREE for one month. Limited time offer-- sign up now! http://join.msn.com/?page=dept/dialup -- [EMAIL PROTECTED] mailing list _ Add MSN 8 Internet Software to your existing Internet access and enjoy patented spam protection and more. Sign up now! http://join.msn.com/?page=dept/byoa -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
How come I can boot from the gentoo CD and not my genkernel (no --config) kernel (on my hd)? They both have the 2.4.20 kernel... andrew From: "a park" <[EMAIL PROTECTED]> Reply-To: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Subject: [gentoo-user] Kernel panic while booting a new Gentoo installation Date: Thu, 25 Sep 2003 12:39:16 -0400 I received the following message while booting with a kernel that I compiled during the installation of Gentoo 2: hub.c: USB hub found hub.c: 3 ports detected Detected usb-ohci hardware Scanning for hid... usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik ([EMAIL PROTECTED]) hid-core.c: USB HID support drivers Detected hid hardware Kernel panic: Attempted to kill init! I compiled the 2.4.20 kernel that is retreived from gentoo-sources. I used the genkernel command without the --config option. I emerged the following: nvidia-kernel, nforce-net, nforce-audio because I have the following hardware: Athlon XP 2200+, Gigabyte GA-7NNXP (nforce2), 256 MB RAM, 40 GB IDE Harddrive (i think it is 7200rpm), NVidia GeForce 4400, Logitech USB Mouse, cdrom, two additional IDE hard drives. I've looked around the web for some answers and most seem to focus on ACPI / APIC and disabling it. I don't mind disabling it as long as I don't see any performance degredation (which is kind of difficult to judge since my machine is not performing at all). There seems to be three places to disable it: the BIOS, the kernel and the boot command (pci=noacpi noapic) (could i place this in lilo.conf?). What would be the best way to determine if this is the problem? Which would be the best place to disable it at? Would this solve my problems? Here is one of the sources of information that I found on the net: http://www.burocrata.org/newwiki/NvidiaNforce Thank you in advance for any and all assistance. Andrew _ Get MSN 8 Dial-up Internet Service FREE for one month. Limited time offer-- sign up now! http://join.msn.com/?page=dept/dialup -- [EMAIL PROTECTED] mailing list _ Instant message in style with MSN Messenger 6.0. Download it now FREE! http://msnmessenger-download.com -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
emerge all that you listed below, but got the following errror when rebooting after finishing the installation process (compiling the kernel, etc). hub.c: USB hub found hub.c: 3 ports detected Detected usb-ohci hardware Scanning for hid... usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik ([EMAIL PROTECTED]) hid-core.c: USB HID support drivers Detected hid hardware Kernel panic: Attempted to kill init! From: Ernie Schroder <[EMAIL PROTECTED]> Reply-To: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Subject: Re: [gentoo-user] Kernel panic while booting a new Gentoo installation Date: Thu, 25 Sep 2003 16:50:42 -0400 The one problem I had was that the cd wouldn't boot untill I passed the nonet option. At the live CD boot prompt, I typed "gentoo nonet" and it booted just fine and picked up the onboard nic automagicly. There is a kernel option for nforce DMA though I did not compile it in. I don't think that my UDMA 133 80 Gig 8Mb buffer Maxtor is suffering though. sudo /sbin/hdparm -Tt /dev/hda /dev/hda: Timing buffer-cache reads: 1352 MB in 2.00 seconds = 674.31 MB/sec Timing buffered disk reads: 172 MB in 3.02 seconds = 56.86 MB/sec Hint for your install: Before rebooting, emerge the nforce-net package or you won't have network drivers (module = nvnet) after rebooting, and you'll have to boot back to the CD. There is a nvaudio ebuild too that you'll probably want at some point On Thursday 25 September 2003 03:37 pm, a park wrote: > ernie, > > did you have to make any bios / boot / kernel adjustments to get > your system to work with the nforce2 chip set? > > andrew > > From: Ernie Schroder <[EMAIL PROTECTED]> > > >Reply-To: [EMAIL PROTECTED] > >To: [EMAIL PROTECTED] > >Subject: Re: [gentoo-user] Kernel panic while booting a new Gentoo > >installation > >Date: Thu, 25 Sep 2003 14:30:13 -0400 > > > >Just so folks don't think that Peter's problems are due to the > > Nforce 2 chipset., I'll report no such problems with my > > LeadtekK7NCR18D (nforce2) mother board. DMA is working, USB and > > USB 2 work perfectly my onboard nic is fine, and the onboard > > firewire seems to work too. My last problem is getting lm-sensors > > working. I tend to stay FAR away from VIA chipsets due to AGP > > problems I experienced with 2 different VIA based boards. Nothing > > against Peter's judgement, just my personal experience > >-- > >Regards, Ernie > >100% Microsoft and Intel free > > _ > High-speed Internet access as low as $29.95/month (depending on the > local service providers in your area). Click here. > https://broadband.msn.com > > > -- > [EMAIL PROTECTED] mailing list -- Regards, Ernie 100% Microsoft and Intel free -- [EMAIL PROTECTED] mailing list _ Help protect your PC. Get a FREE computer virus scan online from McAfee. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963 -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
The one problem I had was that the cd wouldn't boot untill I passed the nonet option. At the live CD boot prompt, I typed "gentoo nonet" and it booted just fine and picked up the onboard nic automagicly. There is a kernel option for nforce DMA though I did not compile it in. I don't think that my UDMA 133 80 Gig 8Mb buffer Maxtor is suffering though. sudo /sbin/hdparm -Tt /dev/hda /dev/hda: Timing buffer-cache reads: 1352 MB in 2.00 seconds = 674.31 MB/sec Timing buffered disk reads: 172 MB in 3.02 seconds = 56.86 MB/sec Hint for your install: Before rebooting, emerge the nforce-net package or you won't have network drivers (module = nvnet) after rebooting, and you'll have to boot back to the CD. There is a nvaudio ebuild too that you'll probably want at some point On Thursday 25 September 2003 03:37 pm, a park wrote: > ernie, > > did you have to make any bios / boot / kernel adjustments to get > your system to work with the nforce2 chip set? > > andrew > > From: Ernie Schroder <[EMAIL PROTECTED]> > > >Reply-To: [EMAIL PROTECTED] > >To: [EMAIL PROTECTED] > >Subject: Re: [gentoo-user] Kernel panic while booting a new Gentoo > >installation > >Date: Thu, 25 Sep 2003 14:30:13 -0400 > > > >Just so folks don't think that Peter's problems are due to the > > Nforce 2 chipset., I'll report no such problems with my > > LeadtekK7NCR18D (nforce2) mother board. DMA is working, USB and > > USB 2 work perfectly my onboard nic is fine, and the onboard > > firewire seems to work too. My last problem is getting lm-sensors > > working. I tend to stay FAR away from VIA chipsets due to AGP > > problems I experienced with 2 different VIA based boards. Nothing > > against Peter's judgement, just my personal experience > >-- > >Regards, Ernie > >100% Microsoft and Intel free > > _ > High-speed Internet access as low as $29.95/month (depending on the > local service providers in your area). Click here. > https://broadband.msn.com > > > -- > [EMAIL PROTECTED] mailing list -- Regards, Ernie 100% Microsoft and Intel free -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
ernie, did you have to make any bios / boot / kernel adjustments to get your system to work with the nforce2 chip set? andrew From: Ernie Schroder <[EMAIL PROTECTED]> Reply-To: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Subject: Re: [gentoo-user] Kernel panic while booting a new Gentoo installation Date: Thu, 25 Sep 2003 14:30:13 -0400 Just so folks don't think that Peter's problems are due to the Nforce 2 chipset., I'll report no such problems with my LeadtekK7NCR18D (nforce2) mother board. DMA is working, USB and USB 2 work perfectly my onboard nic is fine, and the onboard firewire seems to work too. My last problem is getting lm-sensors working. I tend to stay FAR away from VIA chipsets due to AGP problems I experienced with 2 different VIA based boards. Nothing against Peter's judgement, just my personal experience -- Regards, Ernie 100% Microsoft and Intel free _ High-speed Internet access as low as $29.95/month (depending on the local service providers in your area). Click here. https://broadband.msn.com -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
On Thursday 25 September 2003 01:44 pm, Peter Ruskin wrote: > On Thursday 25 Sep 2003 17:39, a park wrote: > > Athlon XP 2200+, Gigabyte GA-7NNXP (nforce2), 256 MB RAM, 40 GB > > IDE Harddrive (i think it is 7200rpm), NVidia GeForce 4400, > > Logitech USB Mouse, cdrom, two additional IDE hard drives. > > I finally gave up on the GA-7NNXP because I just couldn't get IDE > working right in linux and this supposedly fast machine felt like a > 386. I also got lots of these messages: > > hda: dma_timer_expiry: dma status == 0x64 > hda: lost interrupt > hda: dma_intr: bad DMA status (dma_stat=70) > hda: dma_intr: status=0x50 { DriveReady SeekComplete } > > ...and substantial disk corruption. It performs great in Windows, > but linux :--( > > The on-board USB and LAN didn't work either, nor did AGPGART. I > swapped the board for a GA-7VT600 1394. That uses the VIA KT600 > chipset and is much more compatible. > > Peter Just so folks don't think that Peter's problems are due to the Nforce 2 chipset., I'll report no such problems with my LeadtekK7NCR18D (nforce2) mother board. DMA is working, USB and USB 2 work perfectly my onboard nic is fine, and the onboard firewire seems to work too. My last problem is getting lm-sensors working. I tend to stay FAR away from VIA chipsets due to AGP problems I experienced with 2 different VIA based boards. Nothing against Peter's judgement, just my personal experience -- Regards, Ernie 100% Microsoft and Intel free -- [EMAIL PROTECTED] mailing list
Re: [gentoo-user] Kernel panic while booting a new Gentoo installation
On Thursday 25 Sep 2003 17:39, a park wrote: > Athlon XP 2200+, Gigabyte GA-7NNXP (nforce2), 256 MB RAM, 40 GB IDE > Harddrive (i think it is 7200rpm), NVidia GeForce 4400, Logitech USB > Mouse, cdrom, two additional IDE hard drives. I finally gave up on the GA-7NNXP because I just couldn't get IDE working right in linux and this supposedly fast machine felt like a 386. I also got lots of these messages: hda: dma_timer_expiry: dma status == 0x64 hda: lost interrupt hda: dma_intr: bad DMA status (dma_stat=70) hda: dma_intr: status=0x50 { DriveReady SeekComplete } ...and substantial disk corruption. It performs great in Windows, but linux :--( The on-board USB and LAN didn't work either, nor did AGPGART. I swapped the board for a GA-7VT600 1394. That uses the VIA KT600 chipset and is much more compatible. Peter -- == Gentoo: Portage 2.0.49-r3 (default-x86-1.4, gcc-3.2.3, glibc-2.3.2-r1, 2.4.22_pre2-gss) kernel-2.4.22_pre2-gss i686 AMD Athlon(tm) XP 3200+ == -- [EMAIL PROTECTED] mailing list
[gentoo-user] Kernel panic while booting a new Gentoo installation
I received the following message while booting with a kernel that I compiled during the installation of Gentoo 2: hub.c: USB hub found hub.c: 3 ports detected Detected usb-ohci hardware Scanning for hid... usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik ([EMAIL PROTECTED]) hid-core.c: USB HID support drivers Detected hid hardware Kernel panic: Attempted to kill init! I compiled the 2.4.20 kernel that is retreived from gentoo-sources. I used the genkernel command without the --config option. I emerged the following: nvidia-kernel, nforce-net, nforce-audio because I have the following hardware: Athlon XP 2200+, Gigabyte GA-7NNXP (nforce2), 256 MB RAM, 40 GB IDE Harddrive (i think it is 7200rpm), NVidia GeForce 4400, Logitech USB Mouse, cdrom, two additional IDE hard drives. I've looked around the web for some answers and most seem to focus on ACPI / APIC and disabling it. I don't mind disabling it as long as I don't see any performance degredation (which is kind of difficult to judge since my machine is not performing at all). There seems to be three places to disable it: the BIOS, the kernel and the boot command (pci=noacpi noapic) (could i place this in lilo.conf?). What would be the best way to determine if this is the problem? Which would be the best place to disable it at? Would this solve my problems? Here is one of the sources of information that I found on the net: http://www.burocrata.org/newwiki/NvidiaNforce Thank you in advance for any and all assistance. Andrew _ Get MSN 8 Dial-up Internet Service FREE for one month. Limited time offer-- sign up now! http://join.msn.com/?page=dept/dialup -- [EMAIL PROTECTED] mailing list