Re: [gentoo-user] Routing: how to enable..
On Sat, 17 Feb 2007 21:22:16 +0100 Roman Naumann <[EMAIL PROTECTED]> wrote: > Hi, please forgive this most probably very simple question, but I > cannot find the correct configuration file to enable routing... > > I have two PCs, one HAS a internet connection to the internet-proxy, > the other one hasn't. > The internet-pc (and I do not mean the proxy-pc) has two ethernet > devices, ra0 and eth0. > > eth0 connects it with the non-internet pc. > > I set up a route to the internet-proxy-px on the internet-pc and it > works fine on it, but the the non-internet pc can't use it! > > Even though the non-internet pc has it's default gw set to the eth0 > ip of the internet pc. > > Thanks for your help. "Michal 'vorner' Vaner" was basically correct. PC2 is now a router, and in its tasks are included not only forwarding packets from PC3 to the outside world, but also forwarding them back to PC3. In the routing table PC2 will need routes to PC3 through eth0, and the same default it has now. Without the right routes, PC2 will try to respond to PC3 through ra0, the default route (I assume). Here is an annotated routing table from a router of mine. >zeus ~ # route >Kernel IP routing table >Destination GatewayGenmask Flags Metric RefUse >Iface >192.168.1.0 * 255.255.255.0 U 0 00 eth1 you can see there the route to the subnet it's plugged into, doesn't need to go through the default rout below. >192.168.10.0* 255.255.255.0 U 0 00 eth0 there's the subnet it forwards for, you'll notice it's different. In my case. There must of course be some way to distinguish between them for routing purposes, but you could also route to a host specifically. >loopback* 255.0.0.0 U 0 00 lo >default davey.spore.ath 0.0.0.0UG0 00 eth1 theres where all other traffic goes, through my internet firewall. However the same is true of the default router davey from the lastline above. >davey ~ # route >Kernel IP routing table >DestinationGateway Genmask Flags Metric Ref Use Iface >192.168.2.0* 255.255.255.0 U 0 0 0 ath0 it routes to a wireless network just like PC1/PC2 in your configuration. >192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 and same as before, for route to the subnet it's plugged into. >c-24-245-14-0.h * 255.255.255.0 U 0 0 0 eth1 for comcast, my cable company's subnet im plugged into >192.168.10.0zeus.spore.ath. 255.255.255.0 UG 0 0 0 eth0 for the subnet above, this is what im talking about. >loopback* 255.0.0.0 U 0 0 0 lo yep >default c-3-0-ubr02.eag 0.0.0.0UG 0 0 0 eth1 and by default, out the cable modem on eth1. this last part is probably the problem Roman Naumann has or had. Don't forget you must enable ip forwarding if you desire to use it: >zeus ~ # cat /proc/sys/net/ipv4/ip_forward >1 here you can see that ip_forward is set to 1 to indicate that i wish to enable forwarding for other computers. To set it as such, command the computer thusly. >zeus ~ # echo 1 > /proc/sys/net/ipv4/ip_forward -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Routing: how to enable..
Michal 'vorner' Vaner wrote: > Hello, > > On Sat, Feb 17, 2007 at 11:07:34PM +0100, Roman Naumann wrote: >> Here the whole configuration: (imagine it as a complicated line of different >> connections through the entire house...) >> [SNIP] > > Hm, I think in theory you should have the PC in the middle with 2 IP > addresses, on each interface different. On each segment (each side of > the middle one) should be IPs from different range and there should be > allowed routing (that I do not know how). It would look like this: > > -->( PC1 ) -- ( PC2 ) -- ( > PC3 ) > > PC2 can comm with all (since it is on both nets). PC3 shloud use IP-C as > its gateway, which will allow it to access PC1. PC1 should have static > route for whole Range2 to IP-B, so it can send to PC3. Now, how is that > set in Windows, who knows.. > > After this all is set, PC1 and PC3 should be able to talk to each other. > However, you will not see the pings unless both directions work. > ...snip... Yeah, this sounds pretty good to me. The subnet assignments are key, as is confirming connectivity at each point. Bridging on PC2 is a good choice too. Not sure if your WiFi router is really in bridge mode or not. Be sure its 'WAN' side is in Range1 and its 'LAN' side is in Range2. JT -- Web:http://www.signless.com E-Mail: [EMAIL PROTECTED] Voice: (503) 616-4816 Cell: (503) 419-8806 Skype: jt.justman -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Routing: how to enable..
Hello, On Sat, Feb 17, 2007 at 11:07:34PM +0100, Roman Naumann wrote: > Here the whole configuration: (imagine it as a complicated line of different > connections through the entire house...) > [SNIP] Hm, I think in theory you should have the PC in the middle with 2 IP addresses, on each interface different. On each segment (each side of the middle one) should be IPs from different range and there should be allowed routing (that I do not know how). It would look like this: -->( PC1 ) -- ( PC2 ) -- ( PC3 ) PC2 can comm with all (since it is on both nets). PC3 shloud use IP-C as its gateway, which will allow it to access PC1. PC1 should have static route for whole Range2 to IP-B, so it can send to PC3. Now, how is that set in Windows, who knows.. After this all is set, PC1 and PC3 should be able to talk to each other. However, you will not see the pings unless both directions work. So, you need to: • PC3: /etc/conf.d/net:routes_eth0 = { default via IP-C } • PC2: enable routing (I guess /etc/conf.d/net too) • PC1: add a static route Range2 -> IP-B. I just hope I did not mess that up. Or you can set up a bridge on PC2 to make both segments one net only: http://gentoo-wiki.com/HOWTO_setup_a_gentoo_bridge Have a nice day -- BOFH Excuse #452: Somebody ran the operating system through a spelling checker. Michal 'vorner' Vaner pgpsG8TMWnIAY.pgp Description: PGP signature
Re: [gentoo-user] Routing: how to enable..
> Roman, > > I'm not quite clear on your configuration. What sort of device is the > internet-proxy? Is it a NAT router, or something else? Are all three > devices in the same subnet? It sounds like you're either trying to work > around not having a hub, or not having a NAT device. Thanks for your answer. Here the whole configuration: (imagine it as a complicated line of different connections through the entire house...) PC1 (the proxy-running-pc) is running windows and a proxy software for the internals of my skydsl connection. [PC1 and Router1 are connected via wired-lan] Router1 is acting as a wlan-lan bridge (but without any direct internet functions..). [Router1 and PC2 are connected via wireless-lan] PC2 (the internet-pc) is running gentoo and has a wireless and a wired-lan connection. [PC2 and PC3 are connected via wired-lan] PC3 (the non-internet-pc) is running genoo and only has a wired-lan connection. All I need is (ping like) access to PC1 to use the internet connection. (Usually adding the http_proxy environment variable or something to PC1's IP-address.) PC2 has Router1 set as the default gateway and can ping PC1 hence. PC3 has set PC2 as the default gateway, but cannot ping anything else than PC2. (...which is directly connected anyway...) I think NAT isn't what I'm looking for, I just need ping access to _one_ specific ip, so, some static routes should do the job. I hope that clarifies my situation. Thanks for your help so far. pgpsHaSFKYUCS.pgp Description: PGP signature
Re: [gentoo-user] Routing: how to enable..
You need something like NAT to be configured on your internet-pc. This maybe help(especially the NAT part): http://www.gentoo.org/doc/en/home-router-howto.xml Best wishes, ;-) On 21:22 Sat 17 Feb , Roman Naumann wrote: > Hi, please forgive this most probably very simple question, but I cannot find > the correct configuration file to enable routing... > > I have two PCs, one HAS a internet connection to the internet-proxy, the > other one hasn't. > The internet-pc (and I do not mean the proxy-pc) has two ethernet devices, > ra0 and eth0. > > eth0 connects it with the non-internet pc. > > I set up a route to the internet-proxy-px on the internet-pc and it works > fine on it, but the the non-internet pc can't use it! > > Even though the non-internet pc has it's default gw set to the eth0 ip of the > internet pc. > > Thanks for your help. pgpurr3L2cPld.pgp Description: PGP signature
Re: [gentoo-user] Routing: how to enable..
Roman Naumann wrote: > Hi, please forgive this most probably very simple question, but I cannot find > the correct configuration file to enable routing... > > I have two PCs, one HAS a internet connection to the internet-proxy, the > other one hasn't. > The internet-pc (and I do not mean the proxy-pc) has two ethernet devices, > ra0 and eth0. > > eth0 connects it with the non-internet pc. > > I set up a route to the internet-proxy-px on the internet-pc and it works > fine on it, but the the non-internet pc can't use it! > > Even though the non-internet pc has it's default gw set to the eth0 ip of the > internet pc. > > Thanks for your help. Roman, I'm not quite clear on your configuration. What sort of device is the internet-proxy? Is it a NAT router, or something else? Are all three devices in the same subnet? It sounds like you're either trying to work around not having a hub, or not having a NAT device. JT -- Web:http://www.signless.com E-Mail: [EMAIL PROTECTED] Voice: (503) 616-4816 Cell: (503) 419-8806 Skype: jt.justman -- gentoo-user@gentoo.org mailing list