Re: dmesg and sensors for ODROID H3
I don't have any other 2.5G capable hardware so I tested by connecting the interfaces to eachother and placed them in different routing domains. With pf disabled I reach about 925 Mbit/sec sustained average with iperf3 in either direction, and a bit more with OpenBSD's own tcpbench(1) which averages at 940-ish Mbit/sec: the maximum of plain gigabit Ethernet. It's a bit puzzling that it lands exactly at the limit of 1 gigabit, since ifconfig confirms that the link has negotiated 2500T full duplex. During the test the machine is running at boost frequency of 2900 MHz (aka "2001 MHz" in Intel Speedstep lingo), and nothing from top(1) suggests that it's even close to being stressed out. Though I notice that all 30-35% of "intr" load happens on a single core. No signs of rge(4) timing out or dropping link or similar. I don't have the 4-port expansion, only the two on-board RTL8125B NICs. On Tue, Apr 18, 2023 at 11:51 PM Nick Owens wrote: > On Tue, Apr 18, 2023 at 7:28 AM stolen data > wrote: > > > > Everything seems to work. Only caveat noticed is that the firmware is > > UEFI-only with no CSM/legacy mode, and it will only boot an OpenBSD > > installation from GPT which must contain an EFI system partition holding > > the bootloader. > > great choice. my ODROID H2+ is still holding strong with the add-in > card for 4 extra NICs. it is a fine home firewall. > > my only complaint is sometimes having > > rge5: watchdog timeout > rge2: watchdog timeout > > in dmesg and occasional link state issues, but i didn't dig into > whether its from the rge driver or stuff i attached. > > if you can, provide an iperf3 result in both forward and reverse mode. > here, i only have about 1.60 Gbit/s in both directions, but that's > fine for my wan link. > > > > > dmesg: > > > > ppb0 at pci0 dev 28 function 0 "Intel Jasper Lake PCIE" rev 0x01: msi > > pci1 at ppb0 bus 1 > > rge0 at pci1 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address > > 00:xx:xx:xx:xx:x1 > > ppb1 at pci0 dev 28 function 1 "Intel Jasper Lake PCIE" rev 0x01: msi > > pci2 at ppb1 bus 2 > > rge1 at pci2 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address > > 00:xx:xx:xx:xx:x2 > > >
Re: dmesg and sensors for ODROID H3
On Tue, Apr 18, 2023 at 7:28 AM stolen data wrote: > > Everything seems to work. Only caveat noticed is that the firmware is > UEFI-only with no CSM/legacy mode, and it will only boot an OpenBSD > installation from GPT which must contain an EFI system partition holding > the bootloader. great choice. my ODROID H2+ is still holding strong with the add-in card for 4 extra NICs. it is a fine home firewall. my only complaint is sometimes having rge5: watchdog timeout rge2: watchdog timeout in dmesg and occasional link state issues, but i didn't dig into whether its from the rge driver or stuff i attached. if you can, provide an iperf3 result in both forward and reverse mode. here, i only have about 1.60 Gbit/s in both directions, but that's fine for my wan link. > > > sensors and timers: > > masheen# sysctl hw.sensors kern.timecounter.choice > hw.sensors.cpu0.temp0=25.00 degC > hw.sensors.cpu0.frequency0=8.00 Hz > hw.sensors.cpu1.frequency0=8.00 Hz > hw.sensors.cpu2.frequency0=8.00 Hz > hw.sensors.cpu3.frequency0=8.00 Hz > hw.sensors.acpitz0.temp0=27.80 degC (zone temperature) > hw.sensors.softraid0.drive0=online (sd1), OK > kern.timecounter.choice=i8254(0) tsc(2000) acpihpet0(1000) acpitimer0(1000) > > > dmesg: > > OpenBSD 7.3 (GENERIC.MP) #1125: Sat Mar 25 10:36:29 MDT 2023 > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP > real mem = 4115353600 (3924MB) > avail mem = 3971211264 (3787MB) > random: good seed from bootblocks > mpath0 at root > scsibus0 at mpath0: 256 targets > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 3.2 @ 0x78d74000 (138 entries) > bios0: vendor American Megatrends Inc. version "5.19" date 02/27/2023 > bios0: HARDKERNEL ODROID-H3 > efi0 at bios0: UEFI 2.7 > efi0: American Megatrends rev 0x50013 > acpi0 at bios0: ACPI 6.2 > acpi0: sleep states S0 S5 > acpi0: tables DSDT FACP MCFG FIDT SSDT SSDT SSDT HPET APIC PRAM SSDT SSDT > NHLT LPIT SSDT SSDT DBGP DBG2 SSDT DMAR SSDT TPM2 WSMT FPDT > acpi0: wakeup devices PEGP(S0) PEGP(S0) PEGP(S0) PEGP(S0) SIO1(S0) RP01(S0) > PXSX(S0) RP02(S0) PXSX(S0) RP03(S0) PXSX(S0) RP04(S0) PXSX(S0) RP05(S0) > PXSX(S0) RP06(S0) [...] > acpitimer0 at acpi0: 3579545 Hz, 24 bits > acpimcfg0 at acpi0 > acpimcfg0: addr 0xc000, bus 0-255 > acpihpet0 at acpi0: 1920 Hz > acpimadt0 at acpi0 addr 0xfee0: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES > cpu0: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB > 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache > cpu0: smt 0, core 0, package 0 > mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges > cpu0: apic clock running at 38MHz > cpu0: mwait min=64, max=64, C-substates=0.2.0.2.2.1.1.1, IBE > cpu1 at mainbus0: apid 2 (application processor) > cpu1: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 > cpu1: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES > cpu1: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB > 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache > cpu1: smt 0, core 1, package 0 > cpu2 at mainbus0: apid 4 (application processor) > cpu2: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.27 MHz, 06-9c-00 > cpu2: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES > cpu2: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB > 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache > cpu2: smt 0, core 2, package 0 > cpu3 at mainbus0: apid 6 (application processor) > cpu3: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 > cpu3: >
dmesg and sensors for ODROID H3
Everything seems to work. Only caveat noticed is that the firmware is UEFI-only with no CSM/legacy mode, and it will only boot an OpenBSD installation from GPT which must contain an EFI system partition holding the bootloader. sensors and timers: masheen# sysctl hw.sensors kern.timecounter.choice hw.sensors.cpu0.temp0=25.00 degC hw.sensors.cpu0.frequency0=8.00 Hz hw.sensors.cpu1.frequency0=8.00 Hz hw.sensors.cpu2.frequency0=8.00 Hz hw.sensors.cpu3.frequency0=8.00 Hz hw.sensors.acpitz0.temp0=27.80 degC (zone temperature) hw.sensors.softraid0.drive0=online (sd1), OK kern.timecounter.choice=i8254(0) tsc(2000) acpihpet0(1000) acpitimer0(1000) dmesg: OpenBSD 7.3 (GENERIC.MP) #1125: Sat Mar 25 10:36:29 MDT 2023 dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP real mem = 4115353600 (3924MB) avail mem = 3971211264 (3787MB) random: good seed from bootblocks mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root bios0 at mainbus0: SMBIOS rev. 3.2 @ 0x78d74000 (138 entries) bios0: vendor American Megatrends Inc. version "5.19" date 02/27/2023 bios0: HARDKERNEL ODROID-H3 efi0 at bios0: UEFI 2.7 efi0: American Megatrends rev 0x50013 acpi0 at bios0: ACPI 6.2 acpi0: sleep states S0 S5 acpi0: tables DSDT FACP MCFG FIDT SSDT SSDT SSDT HPET APIC PRAM SSDT SSDT NHLT LPIT SSDT SSDT DBGP DBG2 SSDT DMAR SSDT TPM2 WSMT FPDT acpi0: wakeup devices PEGP(S0) PEGP(S0) PEGP(S0) PEGP(S0) SIO1(S0) RP01(S0) PXSX(S0) RP02(S0) PXSX(S0) RP03(S0) PXSX(S0) RP04(S0) PXSX(S0) RP05(S0) PXSX(S0) RP06(S0) [...] acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimcfg0 at acpi0 acpimcfg0: addr 0xc000, bus 0-255 acpihpet0 at acpi0: 1920 Hz acpimadt0 at acpi0 addr 0xfee0: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES cpu0: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache cpu0: smt 0, core 0, package 0 mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges cpu0: apic clock running at 38MHz cpu0: mwait min=64, max=64, C-substates=0.2.0.2.2.1.1.1, IBE cpu1 at mainbus0: apid 2 (application processor) cpu1: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES cpu1: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache cpu1: smt 0, core 1, package 0 cpu2 at mainbus0: apid 4 (application processor) cpu2: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.27 MHz, 06-9c-00 cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES cpu2: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache cpu2: smt 0, core 2, package 0 cpu3 at mainbus0: apid 6 (application processor) cpu3: Intel(R) Celeron(R) N5105 @ 2.00GHz, 798.28 MHz, 06-9c-00 cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES cpu3: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line 12-way L2 cache, 4MB 64b/line 16-way L3 cache cpu3: smt 0, core 3, package 0 ioapic0 at mainbus0: apid 2 pa 0xfec0, version 20, 120 pins acpiprt0 at acpi0: bus 0 (PC00) acpiprt1 at acpi0: bus 1 (RP01) acpiprt2 at acpi0: bus 2 (RP02) acpiprt3 at acpi0: bus -1 (RP03) acpiprt4 at acpi0: bus -1 (RP04) acpiprt5 at acpi0: bus -1 (RP06) acpiprt6 at
