AW: [mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
I have this problem too sometimes, but then also tuning with other programs (like kaffeine works not!!) -Ursprüngliche Nachricht- Von: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Im Auftrag von Uwe Schmidt Gesendet: Dienstag, 20. September 2005 14:49 An: mythtv-users@mythtv.org Betreff: [mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2 > Anyway I am glad to hear that the scanning was working with skystar > card (btw. do you have skystar2 or skystar1 cards?). I was afraid that > it is the driver issue (it looks like everybody in the mailing list is > using these PVR-XXX cards...). > I will probably try some older versions of mythtv, maybe the 18.1 and > the SVN snapshot has really broken DVB-S scan functionality. > > Thank you. > Bob Bob, I used .18 and .18.1 along with DVB-S on ASTRA, both did the job. Technotrend and Skystar cards. But, when I start mythbackend and mythfrontend on the same system, I sometimes get the same logentries, and the backend says something like "DVB0 no data from card...". Do you have the same ? Only a reboot fixed the problem then, restarting myth does not. Switched to .18, "seems" to be more resistant against this, but perhaps is not. Do not know. Some Entries in the mailing list cover the same problem, but no solution. Not using mythfrontend on the backend machine and no problem anymore. If you need a db-dump, write an email. I will provide you a complete db of my production box. hth, uwe -- GMX DSL = Maximale Leistung zum minimalen Preis! 2000 MB nur 2,99, Flatrate ab 4,99 Euro/Monat: http://www.gmx.net/de/go/dsl ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
[mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2 - SOLVED
Hi John,On 9/20/05, John Pullan <[EMAIL PROTECTED]> wrote: Daft question, but do you have your initial channel to tune to set tosomething appropriate e.g 28106 for "Das Erste" ? Bingo! This is a goog question! Stupid me... Actualy I tried to set the initial channel before, but the mythbackend was running, i.e. the new value was not set/applied after this "change" (and I didn't notice it). Now I did it again - stopped the mythbackend, changed the initial channel, started mythbackend, started mythfrontend - and it works! Finally I will sleep well tonight :o) Now I can see that it is not so difficult to set the whole system, but there is a lot of confusing things like empty unused tables (dvb_channel, dvb_pids), useless debug messages (DVB#0 ERROR - No PIDS set, please correct your channel setup.) etc., which misguided me to the wrong way. But on the other hand, it's for free :) Thanks everybody helping me in this thread!!! Cheers Bob ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
Re: [mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
Hi Uwe, On 9/20/05, Uwe Schmidt <[EMAIL PROTECTED]> wrote: I used .18 and .18.1 along with DVB-S on ASTRA, both did the job.Technotrend and Skystar cards.But, when I start mythbackend and mythfrontend on the same system, Isometimes get the same logentries, and the backend says something like "DVB0 no data from card...". Do you have the same ? Only a reboot fixed theproblem then, restarting myth does not. On my system there is a message like 2005-09-19 23:51:28.962 taking too long to be allowed to read.. 2005-09-19 23:51:28.962 Took more than 10 seconds to be allowed to read, aborting. Couldn't read file: rbuf://127.0.0.1:6543/tmp//ringbuf1.nuv2005-09-19 23:51:28.997 Changing from None to WatchingLiveTV 2005-09-19 23:51:28.998 Decoder not alive, and trying to play.. 2005-09-19 23:51:29.973 RemoteFile::Read() failed in RingBuffer::safe_read(). but this could probably be a problem with some rights, as Jochen pointed out. I will try to increase the backend verbosity level. In your case I would also try to unload the DVB related modules and load them again with rmmod and modprobe (if they are not compiled in the kernel), before the reboot. I will see how it will work for me... If you need a db-dump, write an email. I will provide you a complete db ofmy production box. Could you please send me your complete mythconverg db dump on my email? I just want to be sure that my problems are not caused by wrong database data. Btw., is your dvb_pids table empty as well? The channel table contains only service IDs. Don't you know where are the video, audio and videotext PIDs saved? But I will see it from your db dump... Thank you! Bob ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
Re: [mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
On 20/09/05, Bob Honzik <[EMAIL PROTECTED]> wrote: > Hi Jochen, > > On 9/20/05, Jochen Kühner <[EMAIL PROTECTED]> wrote: > > I hope i can help you... > > > > The DVB data in your Tables in correct. > > > > The dvb_pids table is also no longer used! > > > > The pid is in the channel table and it is correct (I have only checked for > > "Das Erste") > > Well, I can see the service ID there in the channel table - e.g. 28106 for > Das Erste. But there should also be video, audio and videotext PIDs > somewhere, I think. I wonder where are they, then. Maybe they are negotiated > somehow "on the fly"? Btw. how do you select the desired audio channel on > Arte, if it is sending in German and french? If you are recording in TS mode then use + and - to change the audio channel. Also there's some database config you can set which will auto select the correct stream. (sorry can't remember the setting) > My dvb_pids table is empty and therefore I assumed THIS is the reason why I > am not able to receive anything. Well, maybe the problem is somewhere > else... Bad assumption, at least if you're running later than 0.16. dvb_pids is no longer used (along with dvb_channel but that's been pointed out before). Daft question, but do you have your initial channel to tune to set to something appropriate e.g 28106 for "Das Erste" ? Regards. -- John ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
[mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
Hi Jochen,On 9/20/05, Jochen Kühner <[EMAIL PROTECTED]> wrote: I hope i can help you...The DVB data in your Tables in correct.The dvb_pids table is also no longer used!The pid is in the channel table and it is correct (I have only checked for"Das Erste") Well, I can see the service ID there in the channel table - e.g. 28106 for Das Erste. But there should also be video, audio and videotext PIDs somewhere, I think. I wonder where are they, then. Maybe they are negotiated somehow "on the fly"? Btw. how do you select the desired audio channel on Arte, if it is sending in German and french? My dvb_pids table is empty and therefore I assumed THIS is the reason why I am not able to receive anything. Well, maybe the problem is somewhere else... Also the data in the mplex table is correct for "Das erste"I have 3 skystar 2 cards, one in rev 3 and two in rev 6. Have you checkt the dvb functionality in an other program like Kaffeine??? Sure. Not in Kaffeine, but I have mplayer installed which shows all FTA channels without problems, I am using channels.conf file gathered by dvbscan. So all the drivers are up and running properly. What kernel are you using?? I use 2.6.11, the skystar module was rewrittenin 2.6.13 I've heard (don't know exactly, but it has a new name in thatkernel!) I am using 2.6.12 but as I said I think this is not the reason. I think this is not a dvb problem, maybe a rights problem?? Yes, that's the question. I will further investigate it. Start thebackend with a higher verbose level I will. Thanks a lot for hints. Bob ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
[mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
> Anyway I am glad to hear that the scanning was working with skystar > card (btw. do you have skystar2 or skystar1 cards?). I was afraid that > it is the driver issue (it looks like everybody in the mailing list is > using these PVR-XXX cards...). > I will probably try some older versions of mythtv, maybe the 18.1 and > the SVN snapshot has really broken DVB-S scan functionality. > > Thank you. > Bob Bob, I used .18 and .18.1 along with DVB-S on ASTRA, both did the job. Technotrend and Skystar cards. But, when I start mythbackend and mythfrontend on the same system, I sometimes get the same logentries, and the backend says something like "DVB0 no data from card...". Do you have the same ? Only a reboot fixed the problem then, restarting myth does not. Switched to .18, "seems" to be more resistant against this, but perhaps is not. Do not know. Some Entries in the mailing list cover the same problem, but no solution. Not using mythfrontend on the backend machine and no problem anymore. If you need a db-dump, write an email. I will provide you a complete db of my production box. hth, uwe -- GMX DSL = Maximale Leistung zum minimalen Preis! 2000 MB nur 2,99, Flatrate ab 4,99 Euro/Monat: http://www.gmx.net/de/go/dsl ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
[mythtv-users] Re: DVB-S channel scan problem with 18.1, Astra 19.2, skystar2
Hi Jochen, thank you very much for your response. On 9/19/05, Jochen Kühner <[EMAIL PROTECTED]> wrote: > Hello, i've 3 skystar cards in my pc and the scan worked, but i don't know > wich version i used because it's 3 or 4 month away. > > When you search for the channels, you have to give a starting frequency and > and symbol rate: > > Example: ARD 27500 28106, but you have to enter in myth: 2750 28106000) > I know how to start the scan process, but the problem is that it doesn't work rigt, I guess. Transponders and particular channels are found, but (probably) not inserted into the database correctly. Here is an example of my mythconverg data: channel table: INSERT INTO channel (chanid, channum, freqid, sourceid, callsign, name, icon, finetune, videofilters, xmltvid, recpriority, contrast, brightness, colour, hue, tvformat, commfree, visible, outputfilters, useonairguide, mplexid, serviceid, atscsrcid) VALUES (1110,'28106',NULL,1,'Das Erste','Das Erste','none',NULL,'','',0,32768,32768,32768,32768,'Default',0,1,'',1,50,28106,0); INSERT INTO channel (chanid, channum, freqid, sourceid, callsign, name, icon, finetune, videofilters, xmltvid, recpriority, contrast, brightness, colour, hue, tvformat, commfree, visible, outputfilters, useonairguide, mplexid, serviceid, atscsrcid) VALUES (,'28107',NULL,1,'Bayerisches FS','Bayerisches FS','none',NULL,'','',0,32768,32768,32768,32768,'Default',0,1,'',1,50,28107,0); INSERT INTO channel (chanid, channum, freqid, sourceid, callsign, name, icon, finetune, videofilters, xmltvid, recpriority, contrast, brightness, colour, hue, tvformat, commfree, visible, outputfilters, useonairguide, mplexid, serviceid, atscsrcid) VALUES (1112,'28108',NULL,1,'hr-fernsehen','hr-fernsehen','none',NULL,'','',0,32768,32768,32768,32768,'Default',0,1,'',1,50,28108,0); INSERT INTO channel (chanid, channum, freqid, sourceid, callsign, name, icon, finetune, videofilters, xmltvid, recpriority, contrast, brightness, colour, hue, tvformat, commfree, visible, outputfilters, useonairguide, mplexid, serviceid, atscsrcid) VALUES (1113,'28109',NULL,1,'arte','arte','none',NULL,'','',0,32768,32768,32768,32768,'Default',0,1,'',1,50,28109,0); dtv_multiplex table (this multiplex corresponds to the channels listed above): INSERT INTO dtv_multiplex (mplexid, sourceid, transportid, networkid, frequency, inversion, symbolrate, fec, polarity, modulation, bandwidth, lp_code_rate, transmission_mode, guard_interval, visible, constellation, hierarchy, hp_code_rate, sistandard, serviceversion, updatetimestamp) VALUES (50,1,1101,1,11836500,'a',2750,'3/4','h','qpsk','a','auto','a','auto',0,'auto','a','auto','dvb',17,20050917221523); So far it looks OK. But, the dvb_pids table is empty! And this is a problem, I think. Could you please send me some sample of your tables? I mean channel, dtv_multiplex and dvb_pids (and any other relevant table, if there is any). > The Dvb_channels table is no longer used!! The channels are in the normal > channels table!!! Well, this is a new information to me. It looks like the database table formats are changing quite often... I found an mythconverg dump in this mailing list, which used the dvb_channel. I was quite confused by that. When I run mythtv, I see only black screen and this on the command line: [EMAIL PROTECTED] ~ $ mythtv 2005-09-19 23:51:11.618 New DB connection, total: 1 Total desktop width=1024, height=768, numscreens=1 2005-09-19 23:51:11.632 Using screen 0, 1024x768 at 0,0 2005-09-19 23:51:11.730 Switching to square mode (G.A.N.T.) 2005-09-19 23:51:13.336 New DB connection, total: 2 2005-09-19 23:51:13.429 Connecting to backend server: 127.0.0.1:6543 (try 1 of 5) 2005-09-19 23:51:13.470 Using protocol version 15 2005-09-19 23:51:13.588 Using protocol version 15 2005-09-19 23:51:18.959 taking too long to be allowed to read.. 2005-09-19 23:51:23.961 taking too long to be allowed to read.. 2005-09-19 23:51:28.962 taking too long to be allowed to read.. 2005-09-19 23:51:28.962 Took more than 10 seconds to be allowed to read, aborting. Couldn't read file: rbuf://127.0.0.1:6543/tmp//ringbuf1.nuv 2005-09-19 23:51:28.997 Changing from None to WatchingLiveTV 2005-09-19 23:51:28.998 Decoder not alive, and trying to play.. 2005-09-19 23:51:29.973 RemoteFile::Read() failed in RingBuffer::safe_read(). 2005-09-19 23:51:30.182 RemoteFile::Read() failed in RingBuffer::safe_read(). 2005-09-19 23:51:30.391 RemoteFile::Read() failed in RingBuffer::safe_read(). 2005-09-19 23:51:30.600 RemoteFile::Read() failed in RingBuffer::safe_read(). 2005-09-19 23:51:30.809 RemoteFile::Read() failed in RingBuffer::safe_read(). 2005-09-19 23:51:30.834 Changing from None to None 2005-09-19 23:51:31.018 RemoteFile::Read() failed in RingBuffer::safe_read(). Anyway I am glad to hear that the scanning was working with skystar card (btw. do you have skystar2 or skystar1 cards?). I was afraid that it is the driver issue (it looks like everybody in the mailing list is using these PVR-XXX